I have also made the CMD_CHECK_CRC_BIT unused for now since we do not check any response crc values yet.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25343 a1c6a512-1295-4272-9138-f99709370657
The internal card does not appear to be HS capable, at least not in 2GB clip+
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25316 a1c6a512-1295-4272-9138-f99709370657
The controller only needs to be reset if we had an error to clean up any leftover trash...
Move comment pertaining to retry variable so it's actually nearby.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25315 a1c6a512-1295-4272-9138-f99709370657
Adjust the initial MCI_MASK value to also mask the MCI_INT_RXDR and MCI_INT_TXDR bits as it seems we don't use them for dma transfers.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25314 a1c6a512-1295-4272-9138-f99709370657
Move CLKDIV macros into clock-target.h.
Only enable the necessary interfaces for the 3 clock registers used for SD.
Add MEMSTICK and SDSLOT registers to bottom of register display in View HW info debug page.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25309 a1c6a512-1295-4272-9138-f99709370657
The registers value does not change so we don't need to read them
This avoids dividing by 0
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25303 a1c6a512-1295-4272-9138-f99709370657
We don't need the post transfer call this way. We check on TRAN state before each partial transfer.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25282 a1c6a512-1295-4272-9138-f99709370657
as3525 comes with a as3517, as3525v2 with a as3543, rename specific
registers accordingly
Existing problems: FM (line out) doesn't work, volume can't go below a
certain point
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25260 a1c6a512-1295-4272-9138-f99709370657
We do not need a stack pointer at this step, and we are sure to not use
memory not initialized yet (like bss)
Fixes FS#11114 (tested on Fuze)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25229 a1c6a512-1295-4272-9138-f99709370657
- buttonlight works
- backlight turns on (quite weak though and no brightness adjustment/backlight off functional)
- don't share drivers with e200v2/fuzev1 for now as it's not entirely clear how dbop plays into this
- deactivte scrollwheel as it's messing up the timer setup in kernel-as3525.c indicating the dbop input reading doesn't work well
- still no working bootloader/no lcd or buttons
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25225 a1c6a512-1295-4272-9138-f99709370657
Fixes some buttons not being read (hold is still buggy)
FlySpray: FS#11111
Author: Pascal Below
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25209 a1c6a512-1295-4272-9138-f99709370657
Especially when using caches we might read the response too fast and get
the response for the previous command instead.
Now Clip+ boots fine with both instruction & data caches enabled, the
delay might need to be lowered though: boot time is a bit longer.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25183 a1c6a512-1295-4272-9138-f99709370657
calc_freq(CLK_PLLA) for as3525v2 simply returns 240MHz instead of calculating until we understand how it is calculated.
Now displays 922T or 926ejs depending on version.
Remove SD and uSD info from as3525v2 as it is not useful due to different SD controller.
Increased the lines used for each page of display on clip screen size.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25120 a1c6a512-1295-4272-9138-f99709370657
Introduce a new .init section for initialisation code, so that it can be copied to an area which is later overwritten before calling. The stack/bss can then overwrite that code, effectively freeing the code size that the initialisation routines need. Gives a few kB ram usage back.
Only implemented for PP and as3525 so far. More targets could be added, as well as more functions.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25013 a1c6a512-1295-4272-9138-f99709370657
SD_ALL_SEND_CID was using cardinfo.cid to store the response instead of the temp array used for long responses.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24944 a1c6a512-1295-4272-9138-f99709370657
Compilation shows a warning for the first argument of the lcd_bitmap() call in show_logo().
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24911 a1c6a512-1295-4272-9138-f99709370657
Remove MCI_HCON read from init_controller() as it now appears unneccesary.
Make sd-init_card() use similar init sequence to the one in sd-as3525.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24903 a1c6a512-1295-4272-9138-f99709370657
I've left in some commented out code for now as this is still a bit experimental.....
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24891 a1c6a512-1295-4272-9138-f99709370657
Differences remaining:
- list of peripherals reset
- CGU_PROC isn't modified on as3525v2
- CGU_PLLA bits aren't known, but we use a known setting for 240MHz
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24868 a1c6a512-1295-4272-9138-f99709370657
Do not use a static variable for buttons, else they're never reset
Remove unneeded code
Move GPIO_DIR setting to init function
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24855 a1c6a512-1295-4272-9138-f99709370657
check all error bits
only signal wakeup on data transfers, not on commands
trim down send_cmd
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24851 a1c6a512-1295-4272-9138-f99709370657
not touching MCI_CTYPE (leaving bus width to 1) gives data transfers
ignore the hardware locked up while error bit for now
remove printf() helper & debug code
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24838 a1c6a512-1295-4272-9138-f99709370657
Disable errors on response timeout since it can happen on SD_SEND_IF_COND
Disable errors on start bit error : it's ignored by the linux driver
No panic on my side with those 2 bits unchecked, but no transfer
completion either.
Note: the Linux driver doesn't implement DMA
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24837 a1c6a512-1295-4272-9138-f99709370657
Reset DMA before transfers and check data transfer over bit in isr
Still no error or data transfer over conditions
Read the correct status register in isr : there is a masked interrupt
status register and a general status register
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24836 a1c6a512-1295-4272-9138-f99709370657
Initial button driver for clip+. I've followed the steps the OF uses to read the buttons.
There is no hold button on the clip+ so for now calling button_hold() siply returns false.
The OF actually sets an additional flag for the 2nd read from D6 and not BUTTON_POWER as I have done here.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24669 a1c6a512-1295-4272-9138-f99709370657
The code assumed LCD pixels were packed on 16 bits values but for the
Clip we use 8 bits values.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24563 a1c6a512-1295-4272-9138-f99709370657
