| .. |
|
sansa-c200v2
|
Sansa c200v2: enable battery charging
|
2010-01-17 14:19:31 +00:00 |
|
sansa-clip
|
Clip+: LCD display (with FlynDice help)
|
2010-02-17 18:43:13 +00:00 |
|
sansa-clipplus
|
Clip+: greylib
|
2010-02-22 10:35:51 +00:00 |
|
sansa-clipv2
|
Sansa as3525v2: move SD embryo code to a common dir
|
2010-01-13 06:44:45 +00:00 |
|
sansa-e200v2
|
Update on even pixel boundaries on the e200v2 for best performance (was forgotten in r24198).
|
2010-01-26 21:31:53 +00:00 |
|
sansa-fuze
|
Sansa AMS: Time has shown that switching between 16 and 32bit mode costs much time (due to the micro delay needed), so do 32bit transfers unconditionally for lcd updates at the cost of updating slightly larger rectangles (gives upto 15% speed up, nearly at maximum now).
|
2010-01-07 22:21:41 +00:00 |
|
sansa-m200v4
|
|
|
|
adc-target.h
|
|
|
|
app.lds
|
|
|
|
ascodec-as3525.c
|
|
|
|
ascodec-target.h
|
|
|
|
audio-as3525.c
|
as3525v2: build normal firmware properly (Clipv2/+)
|
2010-02-22 02:42:58 +00:00 |
|
backlight-e200v2-fuze.c
|
|
|
|
boot.lds
|
Clip+ boots with iram mapped at 0x0, only the clipv2 is different
|
2010-02-22 05:41:05 +00:00 |
|
button-e200v2-fuze.c
|
Sansa AMS: refactor DBOP button reading (e200v2/Fuze/c200v2)
|
2010-01-06 23:41:36 +00:00 |
|
clock-target.h
|
as3525v2: share more of system_init() between the 2 SoCs
|
2010-02-23 06:59:58 +00:00 |
|
dbop-as3525.c
|
Sansa AMS: Time has shown that switching between 16 and 32bit mode costs much time (due to the micro delay needed), so do 32bit transfers unconditionally for lcd updates at the cost of updating slightly larger rectangles (gives upto 15% speed up, nearly at maximum now).
|
2010-01-07 22:21:41 +00:00 |
|
dbop-as3525.h
|
Sansa AMS: Time has shown that switching between 16 and 32bit mode costs much time (due to the micro delay needed), so do 32bit transfers unconditionally for lcd updates at the cost of updating slightly larger rectangles (gives upto 15% speed up, nearly at maximum now).
|
2010-01-07 22:21:41 +00:00 |
|
debug-as3525.c
|
Sansa AMS: refactor DBOP button reading (e200v2/Fuze/c200v2)
|
2010-01-06 23:41:36 +00:00 |
|
debug-target.h
|
|
|
|
dma-pl081.c
|
Sansa AMS: VIC_INT_ENABLE register is not a mask
|
2009-11-24 12:05:53 +00:00 |
|
dma-target.h
|
Add DMA line for SSP as used in Clip+
|
2010-02-08 08:13:52 +00:00 |
|
fmradio-i2c-as3525.c
|
FS#10047 : Clipv2
|
2009-12-31 19:15:20 +00:00 |
|
i2s-as3525.c
|
|
|
|
kernel-as3525.c
|
Sansa AMS: VIC_INT_ENABLE register is not a mask
|
2009-11-24 12:05:53 +00:00 |
|
lcd-as-e200v2-fuze.S
|
Sansa e200v2/Fuze: Optimize YUV blitting by writing 2 pixel at once to the DBOP and removing a few unneeded busy polling status register for fifo empty. Speed up between 50% and 80%.
|
2010-01-08 16:41:36 +00:00 |
|
pcm-as3525.c
|
Sansa AMS: allow use of PLL B for more accurate audio sample rate (0.04% instead 0.15% error)
|
2010-01-10 14:24:45 +00:00 |
|
power-as3525.c
|
Make si4700 tuner driver more sane with bit and field defines and entirely hide strange i2c interface from code with write/set/clear/masked functionality. On Gigabeat S use by-the-book busmode selection and GPIO lines. Implement some primitive station detection, debug registers in screen, and misc. changes to tie things together.
|
2008-12-27 19:18:50 +00:00 |
|
powermgmt-as3525.c
|
|
|
|
powermgmt-target.h
|
Make Clip+ bootloader build
|
2010-02-05 12:40:25 +00:00 |
|
sd-as3525.c
|
Sansa AMS: remove "ata" from SD drivers filenames
|
2010-01-15 14:03:41 +00:00 |
|
sd-as3525v2.c
|
Comment out unused variable (fix yellow)
|
2010-02-24 23:22:19 +00:00 |
|
system-as3525.c
|
as3525v2: share more of system_init() between the 2 SoCs
|
2010-02-23 06:59:58 +00:00 |
|
system-target.h
|
|
|
|
timer-as3525.c
|
Sansa AMS: VIC_INT_ENABLE register is not a mask
|
2009-11-24 12:05:53 +00:00 |
|
usb-as3525.c
|
|
|
|
usb-drv-as3525.c
|
Sansa AMS: VIC_INT_ENABLE register is not a mask
|
2009-11-24 12:05:53 +00:00 |
abacbbda6c