Add define in config file to enable RTC support in rockbox,
Fix time_menu.c to include radio.h only when tuner is present
Implement time setting function on linux (was empty stub)
Not tested.
Change-Id: I40e6c4a6c1b66ada9cf4e698e502e221d0fc44df
Actual / of underlying linux OS should not be available to user.
I am still not sure if implementation is correct. It doesn't
perform any relative path sandboxing for example.
Change-Id: Ic577a10f3947f6e950e2c4d03173f9f207395eb7
Does away the statically-allocated track list which frees quite
a fair amount of in-RAM size.
There's no compile-time hard track limit.
Recommended TODO (but not right away): Have data small enough use
the handle structure as its buffer data area. Almost the entire
handle structure is unused for simple allocations without any
associated filesystem path.
Change-Id: I74a4561e5a837e049811ac421722ec00dadc0d50
Instead of checking ticks, set a sticky dirty flag that indicates
that the RTC needs to be read. This gives a timely update and more
accurate readout without actually reading the RTC until it changes.
The implementation should atomically read the flag and clear it.
Setting the flag would typically happen in an RTC tick ISR.
Change-Id: I6fd325f22845029a485c502c884812d3676026ea
None of the Sony up to A15 seem to support RDS (they use either Si4702 or Si4708),
thus I did not add any code to support RDS.
Change-Id: I64838993b9705b36b94665f8470c7a89c772c961
Adds the ability to load firmware from other drives on MULTIVOLUME targets
Mihail Zenkov <mihail.zenkov@gmail.com> had posted a hard coded patch
to allow this on several Sansa players, I made it more universal
Redirect file rockbox_main.<name> should placed in root of
drive you would like to be main, if this file empty or there a single
slash '/' firmware will be loaded from /.rockbox in root of this drive
If instead a /<*DIRECTORY*> is supplied in rockbox_main.<name> then
firmware will be loaded from /<dir>/.rockbox/
NOTES*
The directory can have multiple levels however..
leading slash MUST be included
trailing slash can be omitted
(eg. /test/.rockbox would be simply '/test' in the redirect file)
Redirect file will not work on internal drive (whatever is default boot drive)
Volume with the highest index containing redirect file will be loaded
first.
Firmware file is checked for boot data region, if missing, firmware
image will not be loaded.
On failure or if no redirect file is found load will fallback to
internal drive
Currently only Sansa Fuze+, Sansa Clip+,
Sansa Clip Zip, Sansa Fuzev2, and Sansa Fuzev1 are implemented.
Players (with HAVE_MULTIVOLUME)
will need #define HAVE_BOOTDATA and #define BOOT_REDIR "rockbox_main.<name>"
added to their config file
boot_data is implemented in crt0.s file (See g#1552)
ARM and IMX233 have aleady been implemented
Once these conditions are met <HAVE_MULTIBOOT> will be defined by config.h
Partitions on the drives are able to have a redirect as
well.
Change-Id: Iada3263919f6bcad7d0d7d8279b4239aafa07ee9
Adds boot data to as3525 devices Sansa C200v2 E200v2 Clip Clipv2 Clip+ ClipZip
fuze, fuzev2 m200v4
Adds boot_data to features.txt
default arm crt0.s now had boot data if HAVE_BOOTDATA is defined
Change-Id: I614a556696540511a69fc12a4520b01c268bf8a9
Bootdata is a special location in the Firmware marked by a magic header
The bootloader is able to copy information to the firmware by locating
this struct and passing data to the firmware when it is loaded but
before it is actually executed
Data is verified by a crc of the bootdata
Change-Id: Ib3d78cc0c3a9d47d6fe73be4747a11b7ad6f0a9e
* Editing a bunch of drivers' thread routines in order to
implement a new feature is tedious.
* No matter the number of storage drivers, they share one thread.
No extra threads needed for CONFIG_STORAGE_MULTI.
* Each has an event callback called by the storage thread.
* A default callback is provided to fake sleeping in order to
trigger idle callbacks. It could also do other default processing.
Changes to it will be part of driver code without editing each
one.
* Drivers may sleep and wake as they please as long as they give
a low pulse on their storage bit to ask to go into sleep mode.
Idle callback is called on its behalf and driver immediately put
into sleep mode.
* Drivers may indicate they are to continue receiving events in
USB mode, otherwise they receve nothing until disconnect (they
do receive SYS_USB_DISCONNECTED no matter what).
* Rework a few things to keep the callback implementation sane
and maintainable. ata.c was dreadful with all those bools; make
it a state machine and easier to follow. Remove last_user_activity;
it has no purpose that isn't served by keeping the disk active
through last_disk_activity instead.
* Even-out stack sizes partly because of a lack of a decent place
to define them by driver or SoC or whatever; it doesn't seem too
critical to do that anyway. Many are simply too large while at
least one isn't really adequate. They may be individually
overridden if necessary (figure out where). The thread uses the
greatest size demanded. Newer file code is much more frugal with
stack space. I barely see use crack 50% after idle callbacks
(usually mid-40s). Card insert/eject doesn't demand much.
* No forcing of idle callbacks. If it isn't necessary for one or
more non-disk storage types, it really isn't any more necessary for
disk storage. Besides, it makes the whole thing easier to implement.
Change-Id: Id30c284d82a8af66e47f2cfe104c52cbd8aa7215
We don't really know what those are supposed to do. They seem to change the
volume curve but it is not very clear what is the intended purpose.
Change-Id: I65f5d18aba139844c23df092277ba17ee8518f96
Strangely it has the SAME encryption key as the E450. Either they didn't bother
changing it or more likely they have exactly the same internals and a slightly
different case.
Change-Id: I39ab88845b3e40db34160c2e61dde421f391df44
This requires a few changes unrelated to the A860 because configure unsets
APPLICATION but the NWZ is an application!
Change-Id: Id91aa23193383ac95886b281653da5286edd9caf
SUPPORTED SERIES:
- NWZ-E450
- NWZ-E460
- NWZ-E470
- NWZ-E580
- NWZ-A10
NOTES:
- bootloader makefile convert an extra font to be installed alongside the bootloader
since sysfont is way too small
- the toolsicon bitmap comes from the Oxygen iconset
- touchscreen driver is untested
TODO:
- implement audio routing driver (pcm is handled by pcm-alsa)
- fix playback: it crashes on illegal instruction in DEBUG builds
- find out why the browser starts at / instead of /contents
- implement radio support
- implement return to OF for usb handling
- calibrate battery curve (NB: of can report a battery level on a 0-5 scale but
probabl don't want to use that ?)
- implement simulator build (we need a nice image of the player)
- figure out if we can detect jack removal
POTENTIAL TODOS:
- try to build a usb serial gadget and gdbserver
Change-Id: Ic77d71e0651355d47cc4e423a40fb64a60c69a80
I'm not sure all the situations it affects, to be honest. The fix
aimed to address the strange symptom here:
http://forums.rockbox.org/index.php/topic,50793.0.html
It turns out that ringbuf_add_cross was used when handles were
butted up against one another with the first parameter equal to
the last, which it interprets as being an empty case when it should
be interpreted as full in the context it was used. To fix this,
introduce full/empty variants of ringbuf_add_cross and ringbuf_sub
and use them at the appropriate time.
The other way to address the problem is ensure there's always at
least a space byte between the end of one handle and the start of
another but this make the code a bit trickier to reason about than
using additional function variants.
bufopen() may yield after creating a handle and so do some more
locking so that the buffering thread doesn't mess things up by
moving anything or not seeing the yet-to-be linked-in allocation.
Add alignof() macro to use proper method to get alignment of
struct memory_handle. That should be useful in general anyway.
It's merely defined as __alignof__ but looks nicer.
Change-Id: If21739eaa33a4f6c084a28ee5b3c8fceecfd87ce
Many includes of fat.h are pointless. Some includes are just for
SECTOR_SIZE. Add a file 'firmware/include/fs_defines.h' for that
and to define tuneable values that were scattered amongst various
headers.
Remove some local definitions of SECTOR_SIZE since they have to be
in agreement with the rest of the fs code anyway.
(We'll see what's in fact pointless in a moment ;)
Change-Id: I9ba183bf58bd87f5c45eba7bd675c7e2c1c18ed5
* Remove unused bits like the radio event and simplify basic
radio interface. It can be more self-contained with rds.h only
required by radio and tuner code.
* Add post-processing to text a-la Silicon Labs AN243. The chip's
error correction can only do so much; additional checks are highly
recommended. Simply testing for two identical messages in a row
is extremely effective and I've never seen corrupted text since
doing that, even with mediocre reception.
Groups segments must arrive in order, not randomly; logic change
only accepts them in order, starting at 0.
Time readout was made a bit better but really we'd need to use
verbose mode and ensure that no errors were seen during receiving
of time and more checks would be need to have a stable PI. The
text is the important bit anyway.
* Time out of stale text.
* Text is no longer updated until a complete group has been
received, as is specified in the standard. Perhaps go back to
scrolling text lines in the radio screen?
* Add proper character conversion to UTF-8. Only the default G0
table for the moment. The other two could be added in.
* Add variants "RDS_CFG_PROCESS" and "RDS_CFG_PUSH" to allow
the option for processed RDS data to be pushed to the driver and
still do proper post-processing (only text conversion for now for
the latter).
Change-Id: I4d83f8b2e89a209a5096d15ec266477318c66925
The implementation is not very complicated but there are a few things worth
noting. There was a previous "speaker enable" setting but it was a boolean.
I decided to replace it with a choice setting that has 2 options (on, off)
if headphones cannot be detect on this target, or 3 options (on, off, auto)
if we can detect headphones. This will break the old setting on target that
cannot detect jack but it makes the code more uniform and avoid maintaining
two settings with more #ifdef. The third option (auto) uses the LANG_AUTO
text, which I think is clear enough (disable speaker on jack plug).
In order to avoid code duplication (both in apps and firmware), I decided to
keep the audiohw_enable_speaker function as-is: it takes a boolean and doesn't
care about the speaker policy. I introduced a new audio_enable_speaker that
takes directly the mode (which follows the setting encoding): 0=off, 1=on
and 2=auto. This way one calls audio_enable_speaker and it changes the speaker
once to reflect the request mode. The apps code then uses this function in the
places where it makes sense: on setting load, setting change and jack (un)plug
event.
Change-Id: I027873f698eb4bc365d7c02b515297806355d9e2
Fix stuff that was bugging me about the way I did it at first.
While messing around I found RDS code wasn't masking its GPIO
ISR as it should, which might lead to two different interrupts
messing with the static data.
Change-Id: I54626809ea3039a842af0cc9e3e42853326c4193
1. Slightly revised and regularized internal interface. Callback is used
for read and write to provide completion signal instead of having two
mechanisms.
2. Lower overhead for asynchronous or alterate completion callbacks. We
now only init what is required by the transfer. A couple unneeded
structure members were also nixed.
3. Fixes a bug that would neglect a semaphore wait if pumping the I2C
interrupts in a loop when not in thread state or interrupts are masked.
4. Corrects broken initialization order by defining KDEV_INIT, which
makes kernel_init() call kernel_device_init() to initialize additional
devices _after_ the kernel, threading and synchronization objects are
safe to use.
5. Locking set_cpu_frequency has to be done at the highest level in
system.c to ensure the boost counter and the frequency are both set in
agreement. Reconcile the locking inteface between PP and AMS (the only
two currently using locking there) to keep it clean.
Now works fine with voltages in GIT HEAD on my Fuze v2, type 0.
Previously, everything crashed and died instantly. action.c calling
set_cpu_frequency from a tick was part of it. The rest may have been
related to 3. and 4. Honestly, I'm not certain!
Testing by Mihail Zenkov indicates it solves our problems. This will
get the developer builds running again after the kernel assert code
push.
Change-Id: Ie245994fb3e318dd5ef48e383ce61fdd977224d4
The function is neither reentrant nor ISR callable. Instead of
using a ticked-based timeout, have the button driver provide the
unboost after a delay when waiting for a button.
HAVE_GUI_BOOST gets immediate boost after dequeuing any message,
otherwise the queue has to have at least three messages waiting
for it to trigger a boost-- essentially the behavior that existed
but now combined in one place.
Change-Id: I1d924702840f56a1a65abe41fa92b4e753c4e75a
Selective backlight allows the user to choose actions that will not
enable the backlight when pressed.
Advanced softlock allows user to choose actions that will not be
blocked by screenlock on devices without a hold button.
Both only occur in FM and WPS Contexts.
Update:
Back from the dead
-Cleaned up code, removed unnecessary calls, re-arranged last filter action
timeout conditional to work in case last_filtered_action_tick was never set
-Added entries to the manual
-Fixed back button on some menus not activating backlight
-Made menus more intuitive, no actions selected now changes menu item to off.
-Added talk fuctionality.
-Added option to disable selective backlight while on external power.
-Rewrote backlight and softlock handling code to fix issue with scrollwheels
-Menu changed to have toggle(yes/no) and settings
-Optimized selective actions lookup
-Added option to disable notification of 'buttons locked' while softlocked
-Removed uneeded code, consolidated action lookup to single function
-Fixed incorrect name on selective softlock menu
-Added option to disable touch on touchscreen devices
-Fixed backlight on original screenlock without selective screenlock active
-Added text selection in mask_select for when show_icons is off
-Fixed voice in mask_select to speak if voice is defined instead of spelling
-Added more lang defines (play skip seek)
-Added option to disable unknown keys turning on backlight
-Fixed Conditional argument In wrong place causing players without
backlight to fail to build
-Fixed Disable Unknown blocking detection of context change
-Fixed canceling menu didn't update new settings
-Added Autolock on backlight off
-Removed backlight_on_force from backlight.c, Now sets ignore next to false
and uses backlight_on
-Cleaned up autolock code added strings to lang file
-Fixed issue where rapid presses would bypass softlock
-Removed old softlock code, Cleaned selective actions code
-Changed menu to match existing RB menus
-Fixed Backlight_on_Hold blocked by backlight_ignore_next
-Fixed ignore_next for ipod
-Fixed bug allowing context with softlock to bypass selective backlight
-Changed mask_select to no longer prompt for changes to be saved
-Changed menu names
-Added ignore timeout to allow ipod scroll wheel to work properly and other
players to still work properly, removed some previous code including
ignore_event
-Increased ignore timeout to prevent sd card accesses from interrupting action
code and turning on backlight
-Changed Unknown action to unmapped action in menu, changed handling code
-Removed unneeded logic and variables for handling unfiltered actions
-Reverted unmapped action code to previous functionality
-Added manual entries (thanks JohnB)
-Removed elusive unhandled unicode character from manual, changed formatting slightly
Actions:
Volume,Play,Seek,Skip
Extras:
Disable unmapped actions
Disable selective backlight on external power
Disable touch during softlock on touchscreen devices
Disable softlock notifications (power button still notifies)
Autolock on backlight off
Method:
Adds a function to ignore backlight on next call
If selected action occurs backlight is forced on,
Filter_first_keypress stays intact.
Selective softlock allows selected actions through, bypasses the normal
softlock routine.
ToDo:
DONE
previous commit (#1) has attribution for folder_select.c which mask_select
is based from.
Change-Id: I08132ddcfd64c81751ef23b720f3ec6d68695fe4
Playlist dircache references should be back in working order.
Reenabling dircache references in the database ramcache is not
yet done as it requires quite a bit of rework. Otherwise, the
database in RAM is functional again.
Some buffer compatibility changes have been made for database
commit because the dircache buffer can no longer be stolen, only
freed by an API call.
Change-Id: Ib57c3e98cb23e798d4439e9da7ebd73826e733a4
The file system rework introduced incompatibility between dircache
and the tagcache ramcache and playlist dircache path caching. This
update makes changes to filesystem code to reintegrate all that.
It also fixes a couple bugs that were found when vetting all the
code. The filestream cache was being reset without regard to
the stream even if it was shared in write mode (made work of
.playlist_control). Better handling of unmounting gives files a
better go at force-closing them without risk to disk integrity.
Did some miscellaneous pedantic changes. Improved efficiency of
testing a file's existence (a little) since the path parser will
be shared between file code and parsing for the sake of finding
dircache references, not duplicated as before.
This commit doesn't reenable said items just for the sake of
keeping changes separate and related.
Plan for the next is to enable dircache again for the playlists
(easy peasy) and reenable tagcache ramcache but *without* the
dircache path caching because it's rather substantial to change
in itself. The ramcache will still function without dircache.
Change-Id: I7e2a9910b866251fa8333e1275f72fcfc8425d2d
Some changes in behavior were made with filesystem code commit
for the sake of compatibility that changed expected behavior.
* Restore substitution of drive spec in fully-qualified DOS paths
with the playlists's volume spec (or root on univolume targets).
Drive-relative paths of the form "c:foo" (no separator after
':') will be treated as purely relative.
* Restore old behavior of preserving leading whitespace in the
source path and trimming only trailing tabs and spaces.
* Multivolume: Volume substition on fully-qualified UNIX/RB paths
has NOT been reintroduced (and perhaps wasn't intended in the
first place). They will not be modified because there is no
ambiguity to resolve. Doing so would prevent a playlist on
external storage from referencing a file on main storage without
qualifying it with "/<0>...".
* Plain relative paths are and always have been interpreted as
relative to the location of the playlist.
Change-Id: Ic0800cea79c59563b7bac20f8b08abb5051906c7
The ZEN X-Fi Style doesn't have an updater like the other stmp targets but at
least the stub enables rebooting to the OF.
Change-Id: I630653a37b94b77210ffdd0d30e1748b13eca96a
Document 3D depth range. Fix mismatch in recording volume: the displayed volume
is completely off the chart
Change-Id: I4c363f369e5d72f332391a6f96457b4e450404f9
The old code made the setting appear as 0dB, 1.5dB, 3dB and 4.5dB when
in fact it is 0dB, 3dB, 4.5dB and 6dB. This commit clarifies the code and
also fix this at the same time. This imx233 3D enhancement is complete crap anyway
but now you can satisfy yourself with 6 dB of pure crap, clearly an enhancement.
Change-Id: Ia3e088987c1ff0cdde228905ff70f46476a499a2
Everytime I use it, I get highly confused because it's complicated and
undocumented. The code is spread all over the place and some targets clearly
use incorrect values. This is the first step of a series to cleanup audio settings
and document it properly.
Change-Id: I20cb7af2bfa33986cb8b0bf8573f17a92227f893
This commit adds the necessary code in the dualboot stub (bootloader) to
let rockbox control the boot process. In particular, rockbox can now choose
if the next boot will be normal (boot rockbox or OF on magic key), to OF
or to updater.
The intents (to be added in follow-up commits) are:
1) Let the user more easily reboot to the OF. On some targets it is not trivial,
especially in USB mode.
2) Automatically reboot to updater when the user drop firmware.sb at the root
of the drive (currently, the user needs to do that in OF USB mode)
3) Document this OF magic
Change-Id: I86df651dec048c318c6a22de74abb8c6b41aa9ad
- Some rewrite with the intent to get ride of these random errors
appearing on some builds/devices (not much noticeable on RB but
can ruin bootloader builds).
- Error handling (ACK).
- IIC clock increased to be the same as in OF.
Change-Id: Idf8cfa3c230a0a61ec9c879bf6f0ea8b061a4607
Add code to read USB D+/D- and accessory ADCs, it is shown in HW
debug menu, might be useful in future for RB and/or the bootloader
to identify external USB chargers.
Change-Id: Ia48ca5e06bb7ddc52bb55abedde6734653ce8dba
Based on g#844 and g#949, it is intended as a replacement for the
current s3c6400x USB driver.
The DesignWare USB OTG core is integrated into many SoC's, however
HW core version and capabilities (mainly DMA mode, Tx FIFO mode,
FIFO size and number of available IN/OUT endpoins) may differ:
CPU targets HW ver DMA NPTX FIFO FIFO sz #IN/OUT
-------- ------------- ------ --- --------- ------- -------
as3525v2 sansaclipplus 2.60a Yes Dedicated 0x535 4/4
sansaclipv2
sansaclipzip
sansafuzev2
s5l8701 ipodnano2g 2.20a Yes Shared 0x500 4/5
s5l8702 ipod6g 2.60a Yes Dedicated 0x820 7/7
ipodnano3g
s5l8720 ipodnano4g ? ? ? ? ?
Functionality supported by this driver:
- Device mode, compatible with USB 1.1/2.0 hosts.
- Shared FIFO (USB_DW_SHARED_FIFO) or dedicated FIFOs.
- No DMA (USB_DW_ARCH_SLAVE) or internal DMA mode.
- Concurrent transfers: control, bulk (usb_storage, usb_serial) and
interrupt (usb_hid).
Actually this driver is not used by any CPU, it will be enabled for
each individual CPU/target in next patches.
Change-Id: I74a1e836d18927a31f6977d71115fb442477dd5f
The old driver was bad in many respect, it had some race conditions, it was
using a thread to serialize transfers because of the legacy i2c interface.
It also had huge latency (typically 50ms but delays up to 300ms can happen),
thus some presses were missed.
The new driver takes advantage of the new i2c driver to do everything
asynchronously. It also does not need a thread anymore because queueing
ensures proper serialization. It provides much better and reliable latency
(typically ~2ms).
Also fix the debug screen which was horribly broken. The new screen also
displays the deadzones.
Change-Id: I69b7f99b75053e6b1d3d56beb4453c004fd2076e
PMU interrupts are used to detect USB Vbus, wall adaptor, accessories
and holdswitch. A thread is needed to poll the PMU throught I2C, ATM
it does nothing but showing the state of the inputs on the HW debug
menu, funcionallity for each individual input will be added in next
patches.
Change-Id: If93bf2044d1052729237a7fd1431c8493e09f1c7
Do not rely on a bootloader initializing the HW, RB initializes
and configures GPIO, I2C, and PMU at startup.
Change-Id: If7f856b1f345f63de584aa4e4fc22d130cd66c80
When the bootloader starts, most of HW never has been initialized.
This patch includes all code needed to perform the preliminary
initialization on SYSCON, GPIO, i2c, and MIU.
The code is based on emCORE and OF reverse engineering, ported to
C for readability.
Change-Id: I9ecf2c3e8b1b636241a211dbba8735137accd05c
The write buffer size is undefined to use the default 24Kb. size
defined (and recomended) in usb_storage.c, the read buffer size is
also decremented to 24 Kb. USB sequential read and write benchmarks
using diskdump are now 8-9% faster.
Change-Id: Ia7c9f77b57c8ca5b566b508efffbd713d1587acf
When the bootloader starts only IRAM is available, the first task is to
ask the PMU to verify if the iPod has previously been hibernated by OF.
Due to memory limitations, the kernel cannot be used on this stage.
This patch modifies I2C and PMU low level functions to not to depend
on kernel (removes mutexes, and uses HW timer instead of current_tick),
actual kernel functions are modified to be 'mutexed' wrappers of the new
functions.
Change-Id: I7cef9e95dedaf176dc0659315f3dc33166d5b116
Add UART support for s5l8700/1 using the UC870X UART controller,
actually the functionallity is disabled and must be enabled for
each individual target. Tested on iPod Nano 2G (s5l8701), not
tested on s5l8700.
Change-Id: Ic0f216bb871502d355a70e4b658e536a2c0976a9
- Small rework on the UC8702 UART controller to make it compatible with
other s5l870x SOCs. Files moved and renamed, many conditional code
added to deal with capabilities and 'features' of the different CPUs.
- A couple of optimizacions that should not affect the functionality.
Change-Id: I705169f7e8b18d5d1da642f81ffc31c4089780a6
With this changes rockbox can be loaded from SD card when internal storage
can't be mount (due to hardware or software problem).
Change-Id: I32b20d3f341566364def747a708a54ba6b4a7f8b
Interrupts version is cause of freeze on USB extraction.
Also non-interrupts version much simpler and faster.
Change-Id: I30a2993cdcaa85abfba77ca06bfacd5b6b4353e2
Fix log file corruption if we have new messages at dumping log to file. Comment
removed as it incorrect. We store all messages in direct order (last message at
end of file).
Change-Id: I4acfa8a0935cc41a889e08f6bc42974fefd1ade2
Voltage is reduced when the CPU is unboosted, resulting in a large
reduction in power consumption. In analogy with the AMSv1 voltage
scaling code (currently disabled due to problems with SD cards),
I have defined a config file option to enable/disable it.
Change-Id: Ia89c31ec06dd012354b4d53435e7b5b36243b206
- Add description for attributes supported by Samsung HS081HA (80Gb)
and HS161JQ (CEATA 160Gb).
- Show error code when ata_read_smart() fails.
Change-Id: I618cc4f37d139fc90f596e2cf3a751346b27deb6
After previous commit 0b6647f2e9
this alignment should not be needed, but not sure at all, so it
is aligned to cache line length for safety.
Change-Id: I5b2b9a30c913d2a609acc1bdf30bdec6811a2551
Some old code made the assumption that CONFIG_CPU == AS3525v2 if and only if
HAVE_AS3543, which is not true on targets like the Samsung YP-R0. This fixes
several issues on such targets like a huge volume gap between -39dB and -40dB
and a volume artificially capped at -72dB instead of -82dB.
Change-Id: Ib1c883ac593c0c3ce5e2bf4eb408924ce5f5ad93
seems more logical to me, and is more consistent, since
"SAMSUNG_YH92X_PAD" is already used in the tex files.
Change-Id: Ie9a9d850ea86155a7dcf86c88a22a420a10a3837
Voltage scaling is not yet enabled, but will follow once we are sure
these changes are stable. Preliminary testing suggests a large
increase in battery life, which will be further improved by voltage
scaling. Patch by Mihail Zenkov with help from myself and others on
the forums.
Change-Id: I171d20bbee19a48c13cd14efb0d023883cc8c687
Configures uncached memory region and adds some defines for misc HW,
for compability with the bootloader and other future use, current
functionality should not be affected.
Change-Id: I390e79bea1aef5b10dfbc72ad327d7fe438ec6f5
This is a rewrite of the clocking section, the resulting system
frequencies are the same as the current git version.
This pàtch uses fixed FClk and just one register is written to switch
all system frequencies, it needs less steps than the current git
version to reach the desired frequency, so it is faster and safer.
Includes functions to step-up/down over a table of predefined set of
frequencies.
The major difference is that Vcore is decreased from 1050 to 1000 mV.
See clocking-s5l8702.h for more information.
Change-Id: I58ac6634e1996adbe1c0c0918a7ce94ad1917d8e
Adds ata_read_smart() function to storage ATA driver, current
SMART data can be displayed and optionally written to hard
disk using System->Debug menu.
Change-Id: Ie8817bb311d5d956df2f0fbfaf554e2d53e89a93
This patch has been tested on iPod 80 and 160slim, actually
it works but some updates must be done to the final version:
- unlimitted input buffer
- decrease CHUNK_SIZE
- use non-cached addresses instead of discard d-cache ???
Capture hardware versions:
Ver iPod models capture support
--- ----------- ---------------
0 80/160fat dock line-in
1 120/160slim dock line-in + jack mic
HW version 1 includes an amplifier for the jack plug mic.
Capture HW detection only tested on iPod 80 and 160slim.
CODEC power:
AFAIK, OF powers CS42L55 at VA=2.4V for capture (1.8V for
playback) and turns on the ADC charge pump. CODEC datasheet
recommmends to disable the charge pump for VA>2.1V.
CS42L55 DS, s4.13 (Required Initialization Settings): for
VA>2.1V, some adjustments "must" be done using undocummented
"control port compensation" registers. OF does not modifies
these registers when VA=2.4V.
This patch configures capture HW in the same way as OF does.
TODO:
- ADC full scale voltage depends on VA, perform tests to find
clipping levels for VA=1.8V and VA=2.4V
Change-Id: I7e20fd3ecaa83b1c58d5c746f5153fe5c3891d75
There are a couple of power saving options that can be selected using
defines, they configure the CODEC in a different way than OF does:
MONO_MIC: jack microphone is connected to left channel, disabling
right channel saves ~1 mW, there is no reason to not to do it.
BYPASS_PGA: this option only applies to the line-in, OF does not
bypass the PGA and configures it to 0 dB gain. At the beginning,
this patch was written based on CODEC datasheet, bypassing PGA
because it saves power and incrementes dinamic range ~1dB, i have
used this setup for a while without problems. Finally this option
was disabled at the last minute, i decided to do it after reviewing
the OF and realizing that CS42L55 datasheet recommends to bypass the
PGA only if the HW includes a couple of capacitors (see Typical
Connection Diagram, Note 4), at this moment i don't know if Classic
includes these capacitors (probably not). Anyway, i am not able to
tell the difference listening to voice recodings.
TODO:
- Use variable PGA gain for jack microphone (it is fixed to +12 dB.
as OF does).
- I am not a fan of having lots of unused #define options, these could
be useful for a generic driver but actually this driver is Classic
oriented, i am not sure if it could be considered disirable to
eliminate them in the final version.
Change-Id: I3dadf2341f44d5e13f3847e6c9de4a76cd6f0918
This patch uses the new pl080 DMA driver for I2S playback and LCD
update. I have tried to be as fiel as possible to the current
behaviour, algorithms and configurations are the same, but using
the new driver. Other modifications:
Playback:
- CHUNK_SIZE is decreased from 42988 to 8188 bytes, it does not
affect normal playback (block size 1024), was tested using
metronome (block size 46080). This change is needed because the
new code commits d-cache range instead of commiting the whole
d-cache, maximum time spent commiting the range should be
limited, CHUNK_SIZE can be decreased even more if necessary.
- pcm_play_dma_start() calls pcm_play_dma_stop() to stop the
channel when it is running (metronome replays the tick sound
without stopping the channel).
- pcm_play_dma_get_peak_buffer(): same as actual SVN function but
returns samples count instead of bytes count.
TODO: AFAIK, actually this function is not used in RB. Not tested,
but probably this function will fail because it returns pointers
to the internal double buffer.
LCD update:
- suppresses lcd_wakeup semaphore and uses yield()
Change-Id: I79b8aa47a941e0dd91847150618f3f7f676c26ef
Motivation:
This driver began as a set of functions to help to test and
experiment with different DMA configurations. It is cumbersome,
time consuming, and leads to mistakes to handle LLIs and DMA
registers dispersed along the code.
Later, i decided to adapt an old DMA queue driver written in the
past for a similar (scatter-gather) controller, all task/queue
code is based on the old driver.
Finally, some cleaning and dmac_ch_get_info() function was added
to complete RB needs.
Description:
- Generic, can be used by other targets including the same
controller. Not difficult to adapt for other similar
controllers if necesary.
- Easy to experiment and compare results using different
setups and/or queue algorithms:
Multi-controller and fully configurable from an unique place.
All task and LLI management is done by the driver, user only
has to (statically) allocate them.
- Two queue modes:
QUEUE_NORMAL: each task in the queue is launched using a new
DMA transfer once previous task is finished.
QUEUE_LINK: when a task is queued, it is linked with the last
queued task, creating a single continuous DMA transfer. New
tasks must be queued while the channel is running, otherwise
the continuous DMA transfer will be broken.
On Classic, QUEUE_LINK mode is needed for I2S continuous
transfers, QUEUE_NORMAL is used for LCD and could be useful
in the future for I2C or UART (non-blocking serial debug) if
necessary.
- Robust DMA transfer progress info (peak meter), needs final
testing, see below.
Technical details about DMA progress:
There are comments in the code related to the method actually
used (sequence method), it reads progress without halting the
DMA transfer. Althought the datasheet does not recommend to do
that, the sequence method seems to be robust, I ran tests calling
dmac_ch_get_info() millions of times and the results were always
as expected (tests done at 2:1 CPU/AHB clock ratio, no other
ratios were tried but probably sequence method will work for any
typical ratio).
This controller allows to halt the transfer and drain the DMAC
FIFO, DMA requests are ignored when the DMA channel is halted.
This method is not suitable for playback because FIFO is never
drained to I2S peripheral (who raises the DMA requests). This
method probably works for capture, the FIFO is drained to memory
before halting.
Another way is to disable (stop) the playback channel. When the
channel is disabled, all FIFO data is lost. It is unknown how much
the FIFO was filled when it was cleared, SRCADDR counter includes
the lost data, therefore the only useful information is LINK and
COUNT, that is the same information disponible when using the
sequence method. At this point we must procced in the same way as
in sequence method, in addition the playback channel should be
relaunched (configure + start) after calculating real SRCADDR.
The stop+relaunch method should work, it is a bit complicated,
and not valid for all peripheral FIFO configurations (depending
on stream rate). Moreover, due to the way the COUNT register is
implemented in HW, I suspect that this method will fail when
source and destination bus widths doesn't match. And more
important, it is not easy to garantize that no sample is lost
here or there, using the sequence method we can always be sure
that playback is ok.
Change-Id: Ib12a1e2992e2b6da4fc68431128c793a21b4b540
This patch implements a simple API to use the external interrupt
hardware present on s5l8702 (GPIO interrupt controller). This
GPIOIC has been fully tested using emcore apps.
Code is based on openiBoot project, there are a few modifications
to optimize space considering we will only use two or three external
interrupts. The API compiles and works, but has been never used,
therefore probably will need some changes to the final version.
External interrupts are necessary for jack remote+mic controller
(see iAP Interface Specifiction: Headphone Remote and Mic System),
this controller is located at I2C bus address 0x72, there is a IRQ
line for remote button press/release events routed to GPIO E6. At
this moment, the functionallity of this controller has been
extensively tested using emcore, getting a lot of information about
how it works. Microphone is already working on RB, jack accessory
detection and button events are work in progress.
PMU IRQ line is also routed to GPIO F3, it signals many events:
holdswitch, usb plug, wall adapter, low battery... The use of PMU
interrupts is the orthodox way of doing things, at this moment
there is no work done in this direction, there are a lot of PMU
events and i think it is a matter of discursion what to do and how.
Change-Id: Icc2e48965e664ca56c9518d84a81c9d9fdd31736
Reorganization
- Separated iBasso devices from PLATFORM_ANDROID. These are now standlone
hosted targets. Most device specific code is in the
firmware/target/hosted/ibasso directory.
- No dependency on Android SDK, only the Android NDK is needed.
32 bit Android NDK and Android API Level 16.
- Separate implementation for each device where feasible.
Code cleanup
- Rewrite of existing code, from simple reformat to complete reimplementation.
- New backlight interface, seperating backlight from touchscreen.
- Rewrite of device button handler, removing unneeded code and fixing memory
leaks.
- New Debug messages interface logging to Android adb logcat (DEBUGF, panicf,
logf).
- Rewrite of lcd device handler, removing unneeded code and fixing memory leaks.
- Rewrite of audiohw device handler/pcm interface, removing unneeded code and
fixing memory leaks, enabling 44.1/48kHz pthreaded playback.
- Rewrite of power and powermng, proper shutdown, using batterylog results
(see http://gerrit.rockbox.org/r/#/c/1047/).
- Rewrite of configure (Android NDK) and device specific config.
- Rewrite of the Android NDK specific Makefile.
Misc
- All plugins/games/demos activated.
- Update tinyalsa to latest from https://github.com/tinyalsa/tinyalsa.
Includes
- http://gerrit.rockbox.org/r/#/c/993/
- http://gerrit.rockbox.org/r/#/c/1010/
- http://gerrit.rockbox.org/r/#/c/1035/
Does not include http://gerrit.rockbox.org/r/#/c/1007/ due to new backlight
interface and new option for hold switch, touchscreen, physical button
interaction.
Rockbox needs the iBasso DX50/DX90 loader for startup, see
http://gerrit.rockbox.org/r/#/c/1099/
The loader expects Rockbox to be installed in /mnt/sdcard/.rockbox/. If
/mnt/sdcard/ is accessed as USB mass storage device, Rockbox will exit
gracefully and the loader will restart Rockbox on USB disconnect.
Tested on iBasso DX50.
Compiled (not tested) for iBasso DX90.
Compiled (not tested) for PLATFORM_ANDROID.
Change-Id: I5f5e22e68f5b4cf29c28e2b40b2c265f2beb7ab7
Some people reported strange charging times and
strange battery life.
Charging by OF: 25 hours; RB: 18 hours
It has been found that there are at least two issues here:
1) the way of getting battery charging status wasn't
really accurate. This attempts to fix that issue.
This patch also simplifies some code (opening a
device is no more needed, for example).
To technically explain, battery charging implies first a constant
current mode (where the voltage increases) and then a constant
voltage mode (where, obviously, the voltage reads more or less
the same). The old way the End Of Charge was detected was based solely
on the voltage, while now it is based on chip's EOC interrupt,
which should be more accurate.
2) OF explicitly sets a constant current 350 mA, while we usually had
55 mA (by as3543 default).
This wasn't discovered before since there is a caching problem
("an accurate guess") in the Samsung power mgmt Linux module,
thus its debugging dumper wasn't really working, reporting a 55 mA current.
Strangely this option should have been set by the bootloader
but apparently it does not.
Some testing is still needed, but I confirm that with this patch
I could run a benchmark for 25 hours (vs. 18 hours), by charging
within Rockbox of course.
Change-Id: I3bd921e86b9018d1cc3c720d15cc46896e8490b3
For some reason, the bootloader and config files didn't define
HAVE_BOOTLOADER_USB_MODE, also remove the special cases in usb.c which they
implied.
Change-Id: I68c29be7d03627e64cac4ff7678e0c211e087a8c
Either by mistake or because its meaning changed, usb_powered() doesn't mean
what the name suggest, so clarify its meaning by renaming it to usb_powered_only.
So use of usb_powered() are replaced by usb_inserted() when it makes more sense.
Change-Id: I112887e2d8560e84587bee5f55c826dde8c806d8
Reviewed-on: http://gerrit.rockbox.org/1097
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Except for unfinished or experimental ports, it isthe case that
USE_ROCKBOX_USB and HAVE_USBSTACK are both defined or both undefined.
Furthermore, it is a leftover of some early developments on the USB stack and
doesn't make sense anymore.
Change-Id: Ic87a865b6bb4c7c9a8d45d1f0bb0f2fb536b8cad
Reviewed-on: http://gerrit.rockbox.org/1091
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Use 32 bytes for cache line length (arm926ej-s), this prevents
misalignments of ATA storage buffer which in some builds could
cause weird faults.
Change-Id: I88dc595d251315620ec49b0251ddc039ff47181e
Reviewed-on: http://gerrit.rockbox.org/1031
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
This changes iBasso DX50/DX90 config from CHARGING_SIMPLE (Simple, hardware
controlled charging (CPU cannot read charger state but may read when power is
plugged-in) to CHARGING_MONITOR (Hardware controlled charging with monitoring
(CPU is able to read HW charging state and when power is plugged-in)).
Not really usefull at the moment, since USB connection (charging) is not (yet)
gracefully handled for iBasso devices.
Change-Id: I55da81b10637d4de88d713ea5eba08eb59bc629f
Reviewed-on: http://gerrit.rockbox.org/1010
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
The port to for this two targets has been entirely developped by Ilia Sergachev (alias Il or xzcc). His source
can be found at https://bitbucket.org/isergachev/rockbox . The few necesary modifications for the DX90 port
was done by headwhacker form head-fi.org. Unfortunately i could not try out the final state of the DX90 port.
The port is hosted on android (without java) as standalone app. The official Firmware is required to run this port.
Ilia did modify the source files for the "android" target in the rockbox source to make the DX port work. The work I did
was to separate the code for DX50 (&DX90) from the android target.
On this Target Ilia used source from tinyalsa from AOSP. I did not touch that part of the code because I do not understand it.
What else I changed from Ilias sources besides the separation from the target "android":
* removed a dirty hack to keep backlight off
* changed value battery meter to voltage battery meter
* made all plugins compile (named target as "standalone") and added keymaps
* i added the graphics for the manual but did not do anything else for the manual yet
* minor optimizations
known bugs:
* timers are slowed donw when playback is active (tinyalsa related?)
* some minor bugs
Things to do:
* The main prolem will be how to install the app correctly. A guy called DOC2008 added a CWM (by androtab.info) to the
official firmware and Ilia made a CWM installation script and a dualboot selector (rbutils/ibassoboot, build with
ndk-build). We will have to find a way to install rockbox in a proper way without breaking any copyrights.
Maybe ADB is an option but it is not enable with OF by default. Patching the OF is probably the way to go.
* All the wiki and manual
to build:
needed: android ndk installed, android sdk installed with additional build-tools 19.1.0 installed
./tools/configure
select iBasso DX50 or iBasso DX90
make -j apk
the content of rockbox.zip/.rockbox needs to be copied to /system/rockbox/app_rockbox/rockbox/ (rockbox app not needed)
the content of libs/armeabi to /system/rockbox/lib/ (rockbox app needed)
The boot selector is needed as /system/bin/MangoPlayer and the iBasso app as /system/bin/MangoPlayer_original. There
is also the "vold" file. The one from OF does not work with DX50 rockbox (DX90 works!?), the one from Ilia is necessary.
Until we have found a proper way to install it, it can only be installed following the instructions of Ilia on his
bitbucket page, using the CWM-OF and his installation script package.
Change-Id: Ic4faaf84824c162aabcc08e492cee6e0068719d0
Reviewed-on: http://gerrit.rockbox.org/941
Tested: Chiwen Chang <rock1104.tw@yahoo.com.tw>
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
To stop erroneous button presses, allow users to add a deadzone between
the button via the Settings > General > System menu > Touch Dead Zone.
The configuration was chosen this way: the touchpad has the same DPI
in both direction so the setting applies the same on both the X and Y
axis. The setting ranges from 0 to 100 and is internally multiplied by 2
giving a maximum deadzone of 2*100 = 200 around each button, which
account for 400 total (once around each button), effectively reducing
each virtual button from 1000x600 to 600x200 when using the maximum value.
Change-Id: I8683c63d2950200eb32d1dda0a00bbd92d83d5be
Reviewed-on: http://gerrit.rockbox.org/677
Reviewed-by: Benjamin Brown <foolshperson@gmail.com>
Tested: Benjamin Brown <foolshperson@gmail.com>
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
HAVE_IO_PRIORITY was defined for native targets with dircache.
It is already effectively disabled for the most part since dircache no
longer lowers its thread's I/O priority. It existed primarily for the
aforementioned configuration.
Change-Id: Ia04935305397ba14df34647c8ea29c2acaea92aa
This patch redoes the filesystem code from the FAT driver up to the
clipboard code in onplay.c.
Not every aspect of this is finished therefore it is still "WIP". I
don't wish to do too much at once (haha!). What is left to do is get
dircache back in the sim and find an implementation for the dircache
indicies in the tagcache and playlist code or do something else that
has the same benefit. Leaving these out for now does not make anything
unusable. All the basics are done.
Phone app code should probably get vetted (and app path handling
just plain rewritten as environment expansions); the SDL app and
Android run well.
Main things addressed:
1) Thread safety: There is none right now in the trunk code. Most of
what currently works is luck when multiple threads are involved or
multiple descriptors to the same file are open.
2) POSIX compliance: Many of the functions behave nothing like their
counterparts on a host system. This leads to inconsistent code or very
different behavior from native to hosted. One huge offender was
rename(). Going point by point would fill a book.
3) Actual running RAM usage: Many targets will use less RAM and less
stack space (some more RAM because I upped the number of cache buffers
for large memory). There's very little memory lying fallow in rarely-used
areas (see 'Key core changes' below). Also, all targets may open the same
number of directory streams whereas before those with less than 8MB RAM
were limited to 8, not 12 implying those targets will save slightly
less.
4) Performance: The test_disk plugin shows markedly improved performance,
particularly in the area of (uncached) directory scanning, due partly to
more optimal directory reading and to a better sector cache algorithm.
Uncached times tend to be better while there is a bit of a slowdown in
dircache due to it being a bit heavier of an implementation. It's not
noticeable by a human as far as I can say.
Key core changes:
1) Files and directories share core code and data structures.
2) The filesystem code knows which descriptors refer to same file.
This ensures that changes from one stream are appropriately reflected
in every open descriptor for that file (fileobj_mgr.c).
3) File and directory cache buffers are borrowed from the main sector
cache. This means that when they are not in use by a file, they are not
wasted, but used for the cache. Most of the time, only a few of them
are needed. It also means that adding more file and directory handles
is less expensive. All one must do in ensure a large enough cache to
borrow from.
4) Relative path components are supported and the namespace is unified.
It does not support full relative paths to an implied current directory;
what is does support is use of "." and "..". Adding the former would
not be very difficult. The namespace is unified in the sense that
volumes may be specified several times along with relative parts, e.g.:
"/<0>/foo/../../<1>/bar" :<=> "/<1>/bar".
5) Stack usage is down due to sharing of data, static allocation and
less duplication of strings on the stack. This requires more
serialization than I would like but since the number of threads is
limited to a low number, the tradoff in favor of the stack seems
reasonable.
6) Separates and heirarchicalizes (sic) the SIM and APP filesystem
code. SIM path and volume handling is just like the target. Some
aspects of the APP file code get more straightforward (e.g. no path
hashing is needed).
Dircache:
Deserves its own section. Dircache is new but pays homage to the old.
The old one was not compatible and so it, since it got redone, does
all the stuff it always should have done such as:
1) It may be update and used at any time during the build process.
No longer has one to wait for it to finish building to do basic file
management (create, remove, rename, etc.).
2) It does not need to be either fully scanned or completely disabled;
it can be incomplete (i.e. overfilled, missing paths), still be
of benefit and be correct.
3) Handles mounting and dismounting of individual volumes which means
a full rebuild is not needed just because you pop a new SD card in the
slot. Now, because it reuses its freed entry data, may rebuild only
that volume.
4) Much more fundamental to the file code. When it is built, it is
the keeper of the master file list whether enabled or not ("disabled"
is just a state of the cache). Its must always to ready to be started
and bind all streams opened prior to being enabled.
5) Maintains any short filenames in OEM format which means that it does
not need to be rebuilt when changing the default codepage.
Miscellaneous Compatibility:
1) Update any other code that would otherwise not work such as the
hotswap mounting code in various card drivers.
2) File management: Clipboard needed updating because of the behavioral
changes. Still needs a little more work on some finer points.
3) Remove now-obsolete functionality such as the mutex's "no preempt"
flag (which was only for the prior FAT driver).
4) struct dirinfo uses time_t rather than raw FAT directory entry
time fields. I plan to follow up on genericizing everything there
(i.e. no FAT attributes).
5) unicode.c needed some redoing so that the file code does not try
try to load codepages during a scan, which is actually a problem with
the current code. The default codepage, if any is required, is now
kept in RAM separarately (bufalloced) from codepages specified to
iso_decode() (which must not be bufalloced because the conversion
may be done by playback threads).
Brings with it some additional reusable core code:
1) Revised file functions: Reusable code that does things such as
safe path concatenation and parsing without buffer limitations or
data duplication. Variants that copy or alter the input path may be
based off these.
To do:
1) Put dircache functionality back in the sim. Treating it internally
as a different kind of file system seems the best approach at this
time.
2) Restore use of dircache indexes in the playlist and database or
something effectively the same. Since the cache doesn't have to be
complete in order to be used, not getting a hit on the cache doesn't
unambiguously say if the path exists or not.
Change-Id: Ia30f3082a136253e3a0eae0784e3091d138915c8
Reviewed-on: http://gerrit.rockbox.org/566
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
We redefine the top-level macros to our own in order to maintain
compatibility with compound initializers by wrapping the mid or low
level definitions from the OS header.
This allows, hopefully optimized, macros from the host OS's headers to
be used when building any hosted target obviating the need for
NEED_GENERIC_BYTESWAPS unless the target simply doesn't define its
own optimized versions (MIPS!).
Throw in some 64-bit swaps for completeness' sake; they generate no code
if not yet used anyway.
Change-Id: I21b384b55fea46833d01ea3cad1ad8952ea01a11
Abstracts threading from itself a bit, changes the way its queues are
handled and does type hiding for that as well.
Do alot here due to already required major brain surgery.
Threads may now be on a run queue and a wait queue simultaneously so
that the expired timer only has to wake the thread but not remove it
from the wait queue which simplifies the implicit wake handling.
List formats change for wait queues-- doubly-linked, not circular.
Timeout queue is now singly-linked. The run queue is still circular
as before.
Adds a better thread slot allocator that may keep the slot marked as
used regardless of the thread state. Assists in dumping special tasks
that switch_thread was tasked to perform (blocking tasks).
Deletes alot of code yet surprisingly, gets larger than expected.
Well, I'm not not minding that for the time being-- omlettes and break
a few eggs and all that.
Change-Id: I0834d7bb16b2aecb2f63b58886eeda6ae4f29d59
find_first_set_bit() becomes a small inline on ARMv5+ and checkwps now gets
made with -std=gnu99 (it eats all the GCCOPTS) like the rest of things.
Change-Id: Ie6039b17fec057a3dcb0f453d8fd5efac984df89
The "percent_to_volt_charge" values are quite arbitrary
and may need some more tweaking.
Change-Id: I9f177d46681030d615fe2c2e78cf9bd2dde026af
Reviewed-on: http://gerrit.rockbox.org/824
Reviewed-by: Szymon Dziok <b0hoon@o2.pl>
Tested: Szymon Dziok <b0hoon@o2.pl>
* e200v2 shouldn't use 24bit (was just for testing)
* samsung ypr0/ypr1 should enable it but the correct number must be passed to bmp2rb
Change-Id: Ia91b0ff80a54265d4c3111d9dcb8e7b9dd12b5d4
With LCD driver all calculation will be performed on RGB888 and the hardware/OS
can display from our 24bit framebuffer.
It is not yet as performance optimized as the existing drivers but should be
good enough.The vast number of small changes is due to the fact that
fb_data can be a struct type now, while most of the code expected a scalar type.
lcd-as-memframe ASM code does not work with 24bit currently so the with 24bit
it enforces the generic C code.
All plugins are ported over. Except for rockpaint. It uses so much memory that
it wouldnt fit into the 512k plugin buffer anymore (patches welcome).
Change-Id: Ibb1964545028ce0d8ff9833ccc3ab66be3ee0754
There is no simple method to detect radio through the 3-wire interface, so it's
not implemented for the YH-925 for now. YH-920 always has a radio.
Change-Id: Iea484d752915fcd40dbbbd7dbbf13e81aaf548db
