NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
Interrupts version is cause of freeze on USB extraction.
Also non-interrupts version much simpler and faster.
Change-Id: I30a2993cdcaa85abfba77ca06bfacd5b6b4353e2
Some old code made the assumption that CONFIG_CPU == AS3525v2 if and only if
HAVE_AS3543, which is not true on targets like the Samsung YP-R0. This fixes
several issues on such targets like a huge volume gap between -39dB and -40dB
and a volume artificially capped at -72dB instead of -82dB.
Change-Id: Ib1c883ac593c0c3ce5e2bf4eb408924ce5f5ad93
There are a couple of power saving options that can be selected using
defines, they configure the CODEC in a different way than OF does:
MONO_MIC: jack microphone is connected to left channel, disabling
right channel saves ~1 mW, there is no reason to not to do it.
BYPASS_PGA: this option only applies to the line-in, OF does not
bypass the PGA and configures it to 0 dB gain. At the beginning,
this patch was written based on CODEC datasheet, bypassing PGA
because it saves power and incrementes dinamic range ~1dB, i have
used this setup for a while without problems. Finally this option
was disabled at the last minute, i decided to do it after reviewing
the OF and realizing that CS42L55 datasheet recommends to bypass the
PGA only if the HW includes a couple of capacitors (see Typical
Connection Diagram, Note 4), at this moment i don't know if Classic
includes these capacitors (probably not). Anyway, i am not able to
tell the difference listening to voice recodings.
TODO:
- Use variable PGA gain for jack microphone (it is fixed to +12 dB.
as OF does).
- I am not a fan of having lots of unused #define options, these could
be useful for a generic driver but actually this driver is Classic
oriented, i am not sure if it could be considered disirable to
eliminate them in the final version.
Change-Id: I3dadf2341f44d5e13f3847e6c9de4a76cd6f0918
Reorganization
- Separated iBasso devices from PLATFORM_ANDROID. These are now standlone
hosted targets. Most device specific code is in the
firmware/target/hosted/ibasso directory.
- No dependency on Android SDK, only the Android NDK is needed.
32 bit Android NDK and Android API Level 16.
- Separate implementation for each device where feasible.
Code cleanup
- Rewrite of existing code, from simple reformat to complete reimplementation.
- New backlight interface, seperating backlight from touchscreen.
- Rewrite of device button handler, removing unneeded code and fixing memory
leaks.
- New Debug messages interface logging to Android adb logcat (DEBUGF, panicf,
logf).
- Rewrite of lcd device handler, removing unneeded code and fixing memory leaks.
- Rewrite of audiohw device handler/pcm interface, removing unneeded code and
fixing memory leaks, enabling 44.1/48kHz pthreaded playback.
- Rewrite of power and powermng, proper shutdown, using batterylog results
(see http://gerrit.rockbox.org/r/#/c/1047/).
- Rewrite of configure (Android NDK) and device specific config.
- Rewrite of the Android NDK specific Makefile.
Misc
- All plugins/games/demos activated.
- Update tinyalsa to latest from https://github.com/tinyalsa/tinyalsa.
Includes
- http://gerrit.rockbox.org/r/#/c/993/
- http://gerrit.rockbox.org/r/#/c/1010/
- http://gerrit.rockbox.org/r/#/c/1035/
Does not include http://gerrit.rockbox.org/r/#/c/1007/ due to new backlight
interface and new option for hold switch, touchscreen, physical button
interaction.
Rockbox needs the iBasso DX50/DX90 loader for startup, see
http://gerrit.rockbox.org/r/#/c/1099/
The loader expects Rockbox to be installed in /mnt/sdcard/.rockbox/. If
/mnt/sdcard/ is accessed as USB mass storage device, Rockbox will exit
gracefully and the loader will restart Rockbox on USB disconnect.
Tested on iBasso DX50.
Compiled (not tested) for iBasso DX90.
Compiled (not tested) for PLATFORM_ANDROID.
Change-Id: I5f5e22e68f5b4cf29c28e2b40b2c265f2beb7ab7
It will be out of scope once the function is left.
cppcheck reported:
[firmware/drivers/rtc/rtc_zenvisionm.c:31]: (error) Pointer to local array variable returned.
[firmware/drivers/rtc/rtc_zenvisionm.c:38]: (error) Pointer to local array variable returned.
Change-Id: Ibf28ba9b3d20cadcaff22398e143488c86746660
Except for unfinished or experimental ports, it isthe case that
USE_ROCKBOX_USB and HAVE_USBSTACK are both defined or both undefined.
Furthermore, it is a leftover of some early developments on the USB stack and
doesn't make sense anymore.
Change-Id: Ic87a865b6bb4c7c9a8d45d1f0bb0f2fb536b8cad
Reviewed-on: http://gerrit.rockbox.org/1091
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
If any of those functions should be (unused) API functions,
they can easily be turned back once really needed.
Detected using a new cppcheck check that
uses the internal symbol database to catch
functions that are only used in the current file.
Change-Id: Ic2b1e5b8020b76397f11cefc4e205f3b7ac1f184
The last big filesystem code refactoring
broke a lot of debug statements.
firmware/test/fat/ doesn't build anymore,
but that's more or less unrelated.
Change-Id: I4c9e1289eeabe1b59d436b176f1d35a02176614f
The port to for this two targets has been entirely developped by Ilia Sergachev (alias Il or xzcc). His source
can be found at https://bitbucket.org/isergachev/rockbox . The few necesary modifications for the DX90 port
was done by headwhacker form head-fi.org. Unfortunately i could not try out the final state of the DX90 port.
The port is hosted on android (without java) as standalone app. The official Firmware is required to run this port.
Ilia did modify the source files for the "android" target in the rockbox source to make the DX port work. The work I did
was to separate the code for DX50 (&DX90) from the android target.
On this Target Ilia used source from tinyalsa from AOSP. I did not touch that part of the code because I do not understand it.
What else I changed from Ilias sources besides the separation from the target "android":
* removed a dirty hack to keep backlight off
* changed value battery meter to voltage battery meter
* made all plugins compile (named target as "standalone") and added keymaps
* i added the graphics for the manual but did not do anything else for the manual yet
* minor optimizations
known bugs:
* timers are slowed donw when playback is active (tinyalsa related?)
* some minor bugs
Things to do:
* The main prolem will be how to install the app correctly. A guy called DOC2008 added a CWM (by androtab.info) to the
official firmware and Ilia made a CWM installation script and a dualboot selector (rbutils/ibassoboot, build with
ndk-build). We will have to find a way to install rockbox in a proper way without breaking any copyrights.
Maybe ADB is an option but it is not enable with OF by default. Patching the OF is probably the way to go.
* All the wiki and manual
to build:
needed: android ndk installed, android sdk installed with additional build-tools 19.1.0 installed
./tools/configure
select iBasso DX50 or iBasso DX90
make -j apk
the content of rockbox.zip/.rockbox needs to be copied to /system/rockbox/app_rockbox/rockbox/ (rockbox app not needed)
the content of libs/armeabi to /system/rockbox/lib/ (rockbox app needed)
The boot selector is needed as /system/bin/MangoPlayer and the iBasso app as /system/bin/MangoPlayer_original. There
is also the "vold" file. The one from OF does not work with DX50 rockbox (DX90 works!?), the one from Ilia is necessary.
Until we have found a proper way to install it, it can only be installed following the instructions of Ilia on his
bitbucket page, using the CWM-OF and his installation script package.
Change-Id: Ic4faaf84824c162aabcc08e492cee6e0068719d0
Reviewed-on: http://gerrit.rockbox.org/941
Tested: Chiwen Chang <rock1104.tw@yahoo.com.tw>
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
For Iriver h100 & h300 series we don't need always use WSPLL,
because in most cases WSPLL clock and SYSCLK has the same value,
and we have additional WSPLL errors to the output clock. Now that is fixed.
Change-Id: I04aebee659c57c45dc8603e409b9db42bdde534a
Reviewed-on: http://gerrit.rockbox.org/434
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
This patch redoes the filesystem code from the FAT driver up to the
clipboard code in onplay.c.
Not every aspect of this is finished therefore it is still "WIP". I
don't wish to do too much at once (haha!). What is left to do is get
dircache back in the sim and find an implementation for the dircache
indicies in the tagcache and playlist code or do something else that
has the same benefit. Leaving these out for now does not make anything
unusable. All the basics are done.
Phone app code should probably get vetted (and app path handling
just plain rewritten as environment expansions); the SDL app and
Android run well.
Main things addressed:
1) Thread safety: There is none right now in the trunk code. Most of
what currently works is luck when multiple threads are involved or
multiple descriptors to the same file are open.
2) POSIX compliance: Many of the functions behave nothing like their
counterparts on a host system. This leads to inconsistent code or very
different behavior from native to hosted. One huge offender was
rename(). Going point by point would fill a book.
3) Actual running RAM usage: Many targets will use less RAM and less
stack space (some more RAM because I upped the number of cache buffers
for large memory). There's very little memory lying fallow in rarely-used
areas (see 'Key core changes' below). Also, all targets may open the same
number of directory streams whereas before those with less than 8MB RAM
were limited to 8, not 12 implying those targets will save slightly
less.
4) Performance: The test_disk plugin shows markedly improved performance,
particularly in the area of (uncached) directory scanning, due partly to
more optimal directory reading and to a better sector cache algorithm.
Uncached times tend to be better while there is a bit of a slowdown in
dircache due to it being a bit heavier of an implementation. It's not
noticeable by a human as far as I can say.
Key core changes:
1) Files and directories share core code and data structures.
2) The filesystem code knows which descriptors refer to same file.
This ensures that changes from one stream are appropriately reflected
in every open descriptor for that file (fileobj_mgr.c).
3) File and directory cache buffers are borrowed from the main sector
cache. This means that when they are not in use by a file, they are not
wasted, but used for the cache. Most of the time, only a few of them
are needed. It also means that adding more file and directory handles
is less expensive. All one must do in ensure a large enough cache to
borrow from.
4) Relative path components are supported and the namespace is unified.
It does not support full relative paths to an implied current directory;
what is does support is use of "." and "..". Adding the former would
not be very difficult. The namespace is unified in the sense that
volumes may be specified several times along with relative parts, e.g.:
"/<0>/foo/../../<1>/bar" :<=> "/<1>/bar".
5) Stack usage is down due to sharing of data, static allocation and
less duplication of strings on the stack. This requires more
serialization than I would like but since the number of threads is
limited to a low number, the tradoff in favor of the stack seems
reasonable.
6) Separates and heirarchicalizes (sic) the SIM and APP filesystem
code. SIM path and volume handling is just like the target. Some
aspects of the APP file code get more straightforward (e.g. no path
hashing is needed).
Dircache:
Deserves its own section. Dircache is new but pays homage to the old.
The old one was not compatible and so it, since it got redone, does
all the stuff it always should have done such as:
1) It may be update and used at any time during the build process.
No longer has one to wait for it to finish building to do basic file
management (create, remove, rename, etc.).
2) It does not need to be either fully scanned or completely disabled;
it can be incomplete (i.e. overfilled, missing paths), still be
of benefit and be correct.
3) Handles mounting and dismounting of individual volumes which means
a full rebuild is not needed just because you pop a new SD card in the
slot. Now, because it reuses its freed entry data, may rebuild only
that volume.
4) Much more fundamental to the file code. When it is built, it is
the keeper of the master file list whether enabled or not ("disabled"
is just a state of the cache). Its must always to ready to be started
and bind all streams opened prior to being enabled.
5) Maintains any short filenames in OEM format which means that it does
not need to be rebuilt when changing the default codepage.
Miscellaneous Compatibility:
1) Update any other code that would otherwise not work such as the
hotswap mounting code in various card drivers.
2) File management: Clipboard needed updating because of the behavioral
changes. Still needs a little more work on some finer points.
3) Remove now-obsolete functionality such as the mutex's "no preempt"
flag (which was only for the prior FAT driver).
4) struct dirinfo uses time_t rather than raw FAT directory entry
time fields. I plan to follow up on genericizing everything there
(i.e. no FAT attributes).
5) unicode.c needed some redoing so that the file code does not try
try to load codepages during a scan, which is actually a problem with
the current code. The default codepage, if any is required, is now
kept in RAM separarately (bufalloced) from codepages specified to
iso_decode() (which must not be bufalloced because the conversion
may be done by playback threads).
Brings with it some additional reusable core code:
1) Revised file functions: Reusable code that does things such as
safe path concatenation and parsing without buffer limitations or
data duplication. Variants that copy or alter the input path may be
based off these.
To do:
1) Put dircache functionality back in the sim. Treating it internally
as a different kind of file system seems the best approach at this
time.
2) Restore use of dircache indexes in the playlist and database or
something effectively the same. Since the cache doesn't have to be
complete in order to be used, not getting a hit on the cache doesn't
unambiguously say if the path exists or not.
Change-Id: Ia30f3082a136253e3a0eae0784e3091d138915c8
Reviewed-on: http://gerrit.rockbox.org/566
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
* HWCODEC bootloaders
* Remove references to thread structures outside the kernel. They are
private and should not be used elsewhere. The mrobe-100 is an offender
that gets squashed.
* The ata.c hack stuff for large sector disks on iPod Video gets squashed
for the same reason. I will no longer maintain it, period; please find
the real reason for its difficulties.
Change-Id: Iae1a675beac887754eb3cc59b560c941077523f5
With LCD driver all calculation will be performed on RGB888 and the hardware/OS
can display from our 24bit framebuffer.
It is not yet as performance optimized as the existing drivers but should be
good enough.The vast number of small changes is due to the fact that
fb_data can be a struct type now, while most of the code expected a scalar type.
lcd-as-memframe ASM code does not work with 24bit currently so the with 24bit
it enforces the generic C code.
All plugins are ported over. Except for rockpaint. It uses so much memory that
it wouldnt fit into the 512k plugin buffer anymore (patches welcome).
Change-Id: Ibb1964545028ce0d8ff9833ccc3ab66be3ee0754
An upcoming lcd-24bit.c driver will re-use a lot of code from the 16bit
drivers, so prepare for that.
Change-Id: I7bc7f6b992e5e3f4e0a0aa54dc08103ebb05315f
There is no simple method to detect radio through the 3-wire interface, so it's
not implemented for the YH-925 for now. YH-920 always has a radio.
Change-Id: Iea484d752915fcd40dbbbd7dbbf13e81aaf548db
Because of architecture of the codec it's always necessary to route the input
signal from ADC to DAC, in order to have a control over the monitoring volume
and in order to hear anything while recording.
Change-Id: I1089894c949ab7371857d74aedb6bdf5a7d39c41
Turn on 4x oversampling inside UDA1380 codec.
This allow will move the quantization noise to the higher frequencies,
that slightly improve the final sound quality.
Change-Id: Idf79cd877c526d8937a47c34e9c180d837a15db1
Reviewed-on: http://gerrit.rockbox.org/435
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
Reviewed-by: Björn Stenberg <bjorn@haxx.se>
Defining HAVE_BUTTON_DATA without simultaneously defining HAVE_TOUCHSCREEN
caused compile errors. (I need them separated for a scrollstrip driver.)
Change-Id: I945d3437d840035ccc0c147f8155029b403c6ec2
Reviewed-on: http://gerrit.rockbox.org/771
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
No code changed, just shuffling stuff around. This should make it easier to
build only select parts kernel and use different implementations.
Change-Id: Ie1f00f93008833ce38419d760afd70062c5e22b5
This is the basic port to the new target Samsung
YP-R1, which runs on a similar platform as YP-R0.
Port is usable, although there are still
some optimizations that have to be done.
Change-Id: If83a8e386369e413581753780c159026d9e41f04
With the new lcd_putsxy_scroll_func() code can register custom scroll functions
(put_line() makes use of that). In order for the custom scroller to be able
to properly manage its userdata pointer (set via struct scrollinfo::userdata)
the scroll engine must inform the scroller about start and stop of scrolling.
To inform about start the lcd_scroll_* functions now return true when
the line will scroll. To inform about stop the scroll engine calls into the
scroller one last time, with the text set to NULL.
put_line() can use this to release the userdata registered per scrolling line
so that it can be recycled.
This fixes that some scrolling lines became glitchy after some time because
the userdata was recycled too early.
Change-Id: Iff0a6ce2a4f9ae2bada1b8e62f4f5950224942a9
This is used by lcd_puts_scroll_worker() to render the line immediately
instead of waiting for the next scroll tick when only the text was updated.
Previously lcd_puts_scroll_worker() did not render anything in this case
which could lead to visible blinking.
This fixes blinking scrolling lines with dynamic text in the skin engine.
Change-Id: I475bde8c8eb7c92f505e3c5ecf4d32bb90690536
1) The 9-segment images need not be multiple of 3 pixels anymore. If it
isn't the inner segments will be smaller than the corners.
2) If the desired actual images is not a multiple of the segment sizes the
function drawed more than the desired rectangle. This is fixed by
drawing the last segment only partially.
Change-Id: Ic918facd8734fa4a4aa72536f0b67de82d81651e
These where used for line styling during scrolling, which is now done in apps/,
The viewport struct doesn't need to record these anymore.
Change-Id: I810d9dcb2644b00a798c6e75acab69c74a78e77f
This logic is moved into apps (put_line()) which can better handle line
decorations with respect to scrolling, mulitline and other complications.
Firmware doesn't need this. The remaining drawing function know only one style,
that is foreground on background/backdrop (changing drawmode is still supported).
Change-Id: I707060edc388a7d723a7d09b0cf5cbda6ec56708
This main (and only) purpose for it was to adjust the pixel position of the text
in otherwise linebased (scrolling) functions. With pixel-based scrolling
this isnt necessary anymore.
Change-Id: I2a45b8ca6a3f8f50aa2f6630201b30ce9ddfe043
Since scrolling is now pixel-based this is not necessary anymore. custom line
height is handled by put_line() but can also possible to implement with
lcd_puts_scroll_func().
Change-Id: Iee9b12bf99afac93d95d2a1a6f5d5b4db237b21c
With this functions removed there is no exported function in firmware left
that draws line decorations. Also no function supports specifying an y-offset
anymore (was used for pixel accurate positioning of otherwise strictly line-based
API calls).
Both should be handled in apps/ now.
Change-Id: Iba4b28ccc6e686c7db63e34b51ad4badae983fce
It is similar to lcd_gradient_fillrect(), except that it only draws a part
of the complete gradient. This can be used to draw only the bottom half
of a full gradient.
Change-Id: Ib47cc5237f6966e35ba07988bddbb00fd97adf96
This function supports installing a custom scroll callback. This will be
called when the scrollengine redraws the line. It allows to draw extended
styles (or anything your can possible imagine) along with the text.
It is also strictly pixel-based, the first pixel-based function that supports
scrolling.
Change-Id: I57f81ac7b3d08b877aea4cb8afa882f175ebcdfc
Some seldomly used drawmode combinations did not work in conjunction with
alpha bitmaps and backdrops. Now all should work (see comment added) by using
more bits.
Change-Id: I2bc96ecf471fa8c1a608a321a235b9c8527b3dc5
bpb_is_sane() used to effectively multiplying the sector size (relative
to 512 bytes) twice, which meant that filesystems with e.g. 2K sectors and
32 sectors per cluster were rejected because while this adds up to 64K
clusters (i.e. the upper limit), the calculation wrongly came to 256K.
This bug tends to affect 5.5G ipods when formatted using dosfstools.
Change-Id: Ia3f1e1303b2af953f497ccdbf23cd49c3d72e46a
Much of the scrolling work is moved from lcd-bitmap-common to lcd-scroll.c,
a small scroll callback routine remains. This callback can potentially be
overridden by more extensive scrollers.
The callback also gets fed with pixel-based scrolling information, which
finally removes the strict line-based nature of the scroll engine. Along with
this is the change from scroll_stop_viewport_line() to scroll_stop_viewport_rect()
which works on a pixel-based rectangle instead of lines.
The ultimate goal is to move most of the scroll work to apps, which can
much better decide which line decorations to apply etc. This work is laying
the ground work.
Change-Id: I3b2885cf7d8696ddd9253d5a9a73318d3d42831a
This allows to draw lines without destroying styles that were drawn manually
(e.g. from apps/) beforehand.
Change-Id: I0de290c9343061efb115e1b76da5b76395c2b2af
Uses a similar technique as lcd_*.c files of #including a common .c file, so
that a unified implementation can be reused for both displays.
Change-Id: I21f6de76df757b093e1a1dff0a4caf96a44fe77e
HiFi E.T. MA8 is almost the same as MA9 except
another DAC(pcm1792 in ma8, df1704 in ma9).
MA8 has ILI9342 lcd, MA8C has ILI9342C lcd.
Change-Id: If2ac04f5a3382590b2a392c46286559f54b2ed6a
Actually 0x20 is the right address, the 0x22 applies to the meizu which
probably use a Chinese clone with a non-spec compliant address.
Change-Id: I65b9ab6477c07a2293226536db3e696d34d3bc2c
The old was doing register read/writes without calling tuner_power(), this
is broken for target with real tuner power management.
Change-Id: I5e60234697a8b91de6189daf6a10e871d5119b65
They share most of registers (except test and some extra bits), since our
driver is very basic, it is safe to relax the manufacurer & chip id check.
Change-Id: If54e8b9e0d852cd9128d5e28ff59bd2c7a55d98d
Target that have a touchpad/touchscreen should disable it while
being locked (In order to avoid LCD to drain battery power due to
"key locked" constant reporting messages. If they a have a keylock
button this was already handled at driver level. If not (e.g. fuze+),
they will have to implement a switch at driver level that action.c
can operate on softlock.
This patch does the following for any target having a touchpad
or a touchscreen and no HAS_BUTTON_HOLD (ie any softlock target)
1) it implements the code to call button_enable_touch(bool en) in
action.c.
2) button_enable_touch is implemented in button.c and call
either touchpad_enable or touchscreen_enable
3) those two function are implemented respectively in touchscreen.c
and a new touchpad.c file. They provide a generic way to silents touch's
device and call a function at driver level where target specific code
can be implemented if possible/needed (for power saving for instance).
Those function name are touchpad_enable_device and touchscreen_enable_device
4) we implement an empty function at driver level of targets that need it
to have them still being able to compiled.
Change-Id: I9ead78a25bd33466a8533f5b9f259b395cb5ce49
Reviewed-on: http://gerrit.rockbox.org/569
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
When using variadic macros there's no need for IF_MD2/IF_MV2 to deal
with function parameters. IF_MD/IF_MV are enough.
Throw in IF_MD_DRV/ID_MV_VOL that return the parameter if MD/MV, or 0
if not.
Change-Id: I7605e6039f3be19cb47110c84dcb3c5516f2c3eb
Implement standard values and functions to operate on power control
register. This allow to modify both reporting rate and sleep mode
in order to save power.
Change-Id: I2bdffd4160e10eec488eb5e19de8a2a258ddbb04
Reviewed-on: http://gerrit.rockbox.org/529
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Using a better resolution causes havoc in the user interface
because it doesn't properly handle steps and people start to
believe I am responsible for all this mess.
Change-Id: I02b68dce5802692efde3da226eeeb49e4995f97a
This adds the application part of alarm wake up. On some targets
like the Fuze+, it will also require a bootloader change to make
sure that the device doesn't power down on alarm wake up (for
example on the Fuze+ the bootloader requires the power button to
be hold sufficiently long, thus preventing alarm wake up to work)
Change-Id: I5d01957852355fddbd48110d3d75a5533f07879e
If target has HW tone controls but no HW prescaler (non-implemented or
non-existent), audiohw_set_prescaler() should, for now, do nothing.
Change-Id: If1b1a36970dca82fda1c350fbaa4d6ce068a6d32
Conversion from centibels to register values was left out of
audiohw_set_lineout_volume().
Credit goes to Dave Marsh for providing the fix.
Just another little oversight from sound/audiohw rework.
Change-Id: I7f8b1c5fb575ac95b5d595c2f4824fbb5ebbd3c8
Just one more SNAFU after redoing sound.c. Software bass/treble controls
in the DSP expect .1 dB gain increments but the gains were being set as
1 dB increments because that's what the AUDIOHW_SETTING specifies. Just
x10 the gains given to audiohw_set_bass/treble.
Change-Id: Id5296f93908ec0036a5605d3a60a2cb5eec91bb5
HAVE_SW_VOLUME_CONTROL is required and at this time only affects the
SDL targets using pcm-sdl.c.
Enables balance control in SDL targets, unless mono volume is in use.
Compiles software volume control as unbuffered when
PCM_SW_VOLUME_UNBUFFERED is defined. This avoids the overhead and
extra latency introduced by the double buffer when it is not needed.
Use this config when the target's PCM driver is buffered and sufficient
latency exists to perform safely the volume scaling.
Simulated targets that are double-buffered when made as native targets
remain so in the sim in order to run the same code.
Change-Id: Ifa77d2d3ae7376c65afecdfc785a084478cb5ffb
Reviewed-on: http://gerrit.rockbox.org/457
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
Based on FS#9920 by Ryan Press with changes to selection logic so
that it works on my iPod Photo. Should also work on iPod Color/4G
and Mini2G. Moved all target specific code from
firmware/drivers/serial.c into new file
firmware/target/arm/pp/uart-pp.c in the same manner as other
target specific uart code.
Update to fix build error on ipodmini2g by adding defines in config file.
Removed unwanted whitespace
Tested on iPod Photo.
Change-Id: Ia5539563966198e06372d70b5adf2ef78882f863
Reviewed-on: http://gerrit.rockbox.org/455
Reviewed-by: andypotter <liveboxandy@gmail.com>
Tested-by: andypotter <liveboxandy@gmail.com>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
* SOUND_x enum can be generated by audiohw_settings.h along with settings
entries and sound_val2phys.
* VOLUME_MIN and VOLUME_MAX are no longer necessary within sound.c. If
you need them, they are for target-defined purposes.
* Fix up SDL volume implementation in sdl.c. Move sim volume calculation
code to pcm-sdl.c.
* Min trigger tresholds were based upon VOLUME_MIN for some reason.
These setting have nothing to do with playback volume. Since it is no
longer present, set these at -89dB which is the minimum peak meter
sensitivity setting.
* Fix an oversight in wm8758.c. I forgot to add the dB->register
conversion to audiohw_set_volume.
Change-Id: Ie1df33f1793eee75e6793f16bc7bddd16edb7f75
This is going right in since it's long overdue. If anything is goofed,
drop me a line or just tweak it yourself if you know what's wrong. :-)
Make HW/SW codec interface more uniform when emulating HW functionality
on SWCODEC for functions such as "audiohw_set_pitch". The firmware-to-
DSP plumbing is in firmware/drivers/audiohw-swcodec.c. "sound_XXX"
APIs are all in sound.c with none in DSP code any longer.
Reduce number of settings definitions needed by each codec by providing
defaults for common ones like balance, channels and SW tone controls.
Remove need for separate SIM code and tables and add virtual codec header
for hosted targets.
Change-Id: I3f23702bca054fc9bda40f49824ce681bb7f777b
Onda VX747 sim was missing a limits #define; #include limits.h in
pcm_sw_volume.h.
Simply use the software volume control for the SIM volume control
rather than the SDL volume control when the target would have it
natively.
Change-Id: I8e924a2ff1b410f602452d2ea9b691efb82c931e
If DRMODE_FG now the alpha channel in bitmaps can be used to draw the bitmap
over the framebuffer, so that e.g. a line selector isn't cleared for
for transparent bitmap pixels.
Change-Id: I09d59a09d2f3c90450a0fe2b83c6c59d757b686b
By saving current_vp fields into temp vars just before the loop gcc can
put them into registers. This yields ~15% speedup for drawing anti-aliased fonts.
Change-Id: I4c0c9f5ff7a7f084e2eb08c4ed874176b1f9832c
The comment about the format was actually incorrect. The alpha information
is now negated during conversion to native format, according to the
corrected comment.
Change-Id: Ifdb9ffdf9b55e39e64983eec2d9d60339e570bd9
Use %x9(id) to draw an image in the whole current viewport using the
9 segment drawer (which draws the corners as normal and *tiles*
the middle segments to the needed width/height).
Future work is to make it scale instead of tile
Change-Id: Ic3ed1cad93f96091694801eb442e0da5a2401203
Our current PS and RT parser is very strict: it requires
all segments to be received in order. This is too strong
of an assumption even when the reception in good, particularly
for long RT messages. This parser handles segments in any order
and completes a message only when all segments are present. To
avoid keeping obsolete segments, each segment has an associated
timeout and is trashed if not updated for a certain period.
Change-Id: I79841bb5ab1f838c7702d8281044e226f6510199
Reviewed-on: http://gerrit.rockbox.org/237
Tested-by: Bertrik Sikken <bertrik@sikken.nl>
Reviewed-by: Bertrik Sikken <bertrik@sikken.nl>
Basically it uses the default SI4700 radio chip driver, the only thing that's different is the I2C access,
written specifically to interact with my kernel module.
Next things to add are:
- RDS support!
Change-Id: I0ed125641e00f93124d7a34f90dd508e7f1db5a4
Signed-off-by: Lorenzo Miori <memorys60@gmail.com>
This change is motivated by the ATA specs, section 9.2 Software reset protocol
(quote):
A host should issue an IDENTIFY DEVICE and/or IDENTIFY PACKET DEVICE
command after the software reset protocol has completed to determine the
current status of features implemented by the device(s).
This indeed fixes a local issue with an SSD in an iriver h320. No other tests
were carried out.
Change-Id: I191444aec3e55f6890020f601c715d0022d09fb6
Reviewed-on: http://gerrit.rockbox.org/218
Reviewed-by: Bertrik Sikken <bertrik@sikken.nl>
Reviewed-by: Linus Nielsen Feltzing <linus@haxx.se>
Reviewed-by: Peter D'Hoye <peter.dhoye@gmail.com>
Tested-by: Peter D'Hoye <peter.dhoye@gmail.com>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
As far as I can say only one file is affected. The loops needs to
go one more time since the end pointer is on the last pixel, not
beyond it.
Change-Id: Ie629138f8399b927bef7bad3847ef42db37e2fed
It was only needed by the old arm toolchain that we no longer use or support.
Change-Id: Id0e6c67477f8834a637079b03cde5fbf9da68b1c
Reviewed-on: http://gerrit.rockbox.org/233
Reviewed-by: Nils Wallménius <nils@rockbox.org>
We use unsigned long/long in number of places in fat.c. When this
is used to cast 32bit fat field it fails on 64bit systems.
This patch introduces explicit types (uint16_t, uint32_t) only
in places which influence how fat structures are interpreted.
Change-Id: I0be44d0b355f9de20b4deb221698d095f55d4bde
Reviewed-on: http://gerrit.rockbox.org/232
Reviewed-by: Frank Gevaerts <frank@gevaerts.be>
Reviewed-by: Torne Wuff <torne@wolfpuppy.org.uk>
%dr(x, y, width, height, [colour1[, colour2]]):
x,y - viewport relative pixel coordinates to start the rectangle.
width, height - obvious. can be '-' to fill the viewport
if both colours are left out the viewports foreground colour will be used
if one colour is specified it will fill the rectangle that colour.
if both colours are specified it will gradient fill the rectangle.
Change-Id: Iad451e99ded663bc7c5d182443659db7d909b388
lcd_gradient_rect() was only usable to draw list lines, so split
it up and make a generic gradient draw function available to apps/
Change-Id: I665911a90fef239b5e06592ea2763cbeeb74c83f
The framebuffer the lcd driver uses can now be changed on the fly
which means that regular lcd_* drawing functions can draw onto the
"backdrop" buffer. The skin engine can use this to create layered
effects.
Add the tag %VB to a viewport to draw that viewport onto the
backdrop layer. If you want to draw an image onto the backdrop
framebuffer use %x(backdrop filename) instead of %X() inside
a viewport with %VB.
Change-Id: I741498e2af6d4f2d78932cabe8942317893e7cfc
Change all lcd drivers to using a pointer to the static framebuffer
instead of directly accessing the static array. This will let us
later do fun things like dynamic framebuffer sizes (RaaA) or
ability to use different buffers for different layers (dynamic
skin backdrops!)
Change-Id: I0a4d58a9d7b55e6c932131b929e5d4c9f9414b06
Remove direct calls to tuner_power(...) in apps/ and let
the driver manage tuner power with the RADIO_SLEEP setting.
Change-Id: I37cd0472e60db5d666dae1b9fe4755dd65c03edd
Reviewed-on: http://gerrit.rockbox.org/84
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
The headphone volume register value reads differently in Line1 and DAC mode.
Since the volume is not set again when switching between playback and radio,
we need to remember the hp volume and reapply setting when changing the mode.
Change-Id: I8fbd344f78653c19d81a39dd3f680ec6885cb1ec
Use two stage amplification (PGA gain and digital stage gain)
combined to extend recgain range to -17.25 +60.0dB.
Change-Id: I4df8af801730b7efb2d35096de077ba31d331222
move prototypes to ascodec.h
move code to ascodec*.c
YPR0: use adc-as3514.c instead of duplicating it
TODO: merge as3514.h and ascodec.h ?
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31626 a1c6a512-1295-4272-9138-f99709370657
It failed to restore macsr to the expected default (FRAC/SAT) which caused DSP
functions like tone control filter calculation to fail (resulting in noise).
The FFT plugin was also affected.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31589 a1c6a512-1295-4272-9138-f99709370657
* Introduce CONFIG_BATTERY_MEASURE define, to allow targets (application)
to break powermgmt.c's assumption about the ability to read battery voltage.
There's now additionally percentage (android) and remaining time measure
(maemo). No measure at all also works (sdl app). If voltage can't be measured,
then battery_level() is king and it'll be used for power_history and runtime
estimation.
* Implement target's API in the simulator, i.e. _battery_voltage(), so it
doesn't need to implement it's own powermgmt.c and other stubs. Now
the sim behaves much more like a native target, although it still
changes the simulated battery voltage quickly,
* Other changes include include renaming battery_adc_voltage() to
_battery_voltage(), for consistency with the new target functions and
making some of the apps code aware that voltage and runtime estimation
is not always available.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31548 a1c6a512-1295-4272-9138-f99709370657
Theoretically, anything with the capability could implement the decoding
action in an ISR on any radio chip supporting RDS.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31464 a1c6a512-1295-4272-9138-f99709370657
It's now using completely the same driver as Sansa daps.
This also increases the volume range.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31428 a1c6a512-1295-4272-9138-f99709370657
This port is a hybrid native/RaaA port. It runs on a embedded linux system,
but is the only application. It therefore can implement lots of stuff that
native targets also implement, while leveraging the underlying linux kernel.
The port is quite advanced. User interface, audio playback, plugins work
mostly fine. Missing is e.g. power mangement and USB (see SamsungYPR0 wiki page).
Included in utils/ypr0tools are scripts and programs required to generate
a patched firmware. The patched firmware has the rootfs modified to load
Rockbox. It includes a early/safe USB mode.
This port needs a new toolchain, one that includes glibc headers and libraries.
rockboxdev.sh can generate it, but e.g. codesourcey and distro packages may
also work.
Most of the initial effort is done by Lorenzo Miori and others (on ABI),
including reverse engineering and patching of the original firmware,
initial drivers, and more. Big thanks to you.
Flyspray: FS#12348
Author: Lorenzo Miori, myself
Merry christmas to ypr0 owners! :)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31415 a1c6a512-1295-4272-9138-f99709370657
Massage the way it interfaces a bit to make things more flexible.
The chroma_buf scheme on Sansa Connect and Creative ZVx calling the
lcd_write_yuv420_lines implementation in lcd-as-memframe.S with five params
with a chroma buffer that the function can't use wouldn't work anyway so just
have them use the stock implementation (really, how was that working?).
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31335 a1c6a512-1295-4272-9138-f99709370657
For this commit: Sansa e200v1, Gigabeat F, Gigabeat S and Mini2440 are
changed over. Quite a number of other targets probably can be as well.
General LCD code is moved out of the target drivers into
drivers/lcd-memframe.c.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31311 a1c6a512-1295-4272-9138-f99709370657
current gcc/binutils don't support weak attribute correctly
see http://sourceware.org/bugzilla/show_bug.cgi?id=9687
fix FS#12427
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31193 a1c6a512-1295-4272-9138-f99709370657
- ata.h is for users of ata.c
- ata-driver.h is for functions implemented by target-specific code and used by ata.c
- ata-target.h is for target-specific defines
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31182 a1c6a512-1295-4272-9138-f99709370657
Included are drivers for buttons, backlight, lcd, audio and storage.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31000 a1c6a512-1295-4272-9138-f99709370657
For images, rows need to be even (this is not true for anti-aliased font files).
Fix stride and size calculation. This makes images that have odd pixel rows display properly and fixes buffer overflows.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30966 a1c6a512-1295-4272-9138-f99709370657
This uses the alpha blending capabilities introduced with anti-aliased fonts
to draw bitmaps with transparency information. The bmp loader is extended to read
this information (pass FORMAT_TRANSPARENT in format). The alpha information will
be used when drawing the bitmap.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30937 a1c6a512-1295-4272-9138-f99709370657
This new APIs wrap around lcd_[mono|transparent]_bitmap/_part calls and
handle all kinds bitmaps. The intended use is to draw bitmaps that
come from read_bmp_fd/_file.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30936 a1c6a512-1295-4272-9138-f99709370657
For the git migration we want a nice clean repository with UNIX line
endings. git does not use svn:eol-style, we just need the file contents to be
sane.
Sorry everybody. I know this messes up blame.
Scumbag *NIX developer says migrating to git will make line ending issues go
away; commits giant change to svn which changes line endings anyway. :)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30924 a1c6a512-1295-4272-9138-f99709370657
This adds line padding to lists on touchscreens,
in order to make lists reasonably useful without huge fonts.
It's configurable:
* Automatic (default, line height calculated using a lcd dpi aware function)
* Off (status quo, line height = font height)
* X pixels (from 2 to 50 in even steps)
The automatic setting should/aims to Just Work Out Of The Box on all targets
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30773 a1c6a512-1295-4272-9138-f99709370657
This event is sent before the audio is routed back to the speaker so we
get the information about the unplugged headphone notably earlier.
Decrease the debouncing of the headphone status from 1s to 0.5s to work
around audio still getting played back via the speaker due to the pause
delay by debouncing. On Android we shouldn't need the debouncing at all.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@29957 a1c6a512-1295-4272-9138-f99709370657
Since the bootloader currently always fails at storage point (unimplemented), always enter touchpad debug screen and power off which pressing power button.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@29859 a1c6a512-1295-4272-9138-f99709370657
1) Set prescaler correctly when 3d enhancement in use.
2) Implement sound_val2phys so gains in recording screen are correct.
3) Minor cleanups.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@29588 a1c6a512-1295-4272-9138-f99709370657
This enables Rockbox to render anti-aliased fonts using an alpha blending method.
The input font bitmaps are 4bit, i.e. 4x larger, but the metadata size stays the same.
A tool, convttf, for converting ttf fonts directly to the Rockbox fnt format is provided.
It has a useful help output, but the parameter that works best is -c1 or -c2 (2 for larger font sizes).
Flyspray: FS#8961
Author: Initial work by Jonas Hurrelmann, further work by Fred Bauer, Andrew Mahone, Teruaki Kawashima and myself.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@29523 a1c6a512-1295-4272-9138-f99709370657
* Remove THREAD_ID_CURRENT macro in favor of a thread_self() function, this allows thread functions to be simpler.
* thread_self_entry() shortcut for kernel.c.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@29521 a1c6a512-1295-4272-9138-f99709370657
Adds Nokia N900, N810 and N800 support.
Features:
- Introduce maemo specific platform defines
- Play audio in silent mode
- Stop playback on incoming calls
- Battery level readout
- Bluetooth headset support
- Save CPU by disabling screen updates if the display
is off or the app doesn't have input focus
- N900: GStreamer audio backend
Kudos to kugel for the code review.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@29248 a1c6a512-1295-4272-9138-f99709370657
