NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
These functions are mostly used by the radio drivers and any blocking
call could potentially block the entire UI, which is pretty bad.
Since any request is expected to finish within a few us, having a 10ms
timeout doesn't seem unreasonable.
Change-Id: I03b19729511547e5bbdeb3476d020e5d87d0d7e1
On targets like stmp3700, resetting the dma channel on "soft" timeout
drives the whole block crazy unless it goes through complete reset.
Change-Id: I830b252279989bf9f9cd9c138240a6ea9b003527
The i2c core has some bugs: it locks up when the slave doesn't NAK and
prevent the dma channel from being resetted. Specifically handle this
situation by setting CLR_GOT_A_NAK (workaround) and then reset dma and i2c
block.
Change-Id: I0e09d38d4301a0ad42dfad785cc934b43f2c4485
A number of pins on the imx233 are standard and manually calling
functions to acquire, set function/drive/output is painful. This
will become unmanageable when we will add support for the other
stmp chips.
Introduce the concept of virtual pin which is a way to completely
describe a virtual pin (virtual because pins are muxed).
Change-Id: I01b6e040945648e58e1d1abab06529c9571c5f10
The current pinctrl functions were a mess. Normalise the functions
names to make them shorter and clearer.
Change-Id: Iac6ff84625ef2b7610268e3a5802dc0088de3167
There are tricky DMA/cache related issue on the imx233 which could
pop up with the old driver. The new one ensures that all dma
tranfers are cache safe by using an intermediate buffer.
Change-Id: I72060682d1c285c83ae16455cfdb62f372b5d687
Because DMA descriptors needs to be committed and discarded from
the cache, if they are not cache aligned and/or if their size
is not a multiple of cache ligne, nasty side effects could occur
with adjacents data. The same applies to DMA buffers which are
still potentially broken. Add a macro to ensure that these
constraints will not break by error in the future.
Change-Id: I1dd69a5a9c29796c156d953eaa57c0d281e79846
The icoll code now has an IRQ storm detection mechanism which
will prevent the device from hard freezing in case it happen.
Change-Id: I9861238dce61d29af1e48f9c534ec63a7f23465c
Past development has proved that one can mistakely use
the same pin for two uses without noticing. Since this
causes extremely hard to find bugs, the infrastructure
will allow to register pin uses and panic when a conflict
is detected. The pinctrl debug now shows the pin uses
when its support is compiled in.
Change-Id: Idb2d5235ce09207d77aa474d6f158e72b933761a
Only enable fmradio_i2c once with _init() called from system.
Move actual i2c init to system for consistency.
Move tuner power pin setup to power instead of fmradio.
Change-Id: Idb56bfba5803f71b5d049f174c48d2afb969a6ea
