Enable simulator for the target ypr0 to
be built and used.
Change-Id: I1b080f07ab90f5c4856881d08ad70e1053bbb0c0
Reviewed-on: http://gerrit.rockbox.org/618
Reviewed-by: Frank Gevaerts <frank@gevaerts.be>
The driver can now handle HOLD in several ways, including using a GPIO.
Also add a debug routine to read the raw value of the adc.
Change-Id: Ide2cb1ac58e759b4bc464e606b432f2c150ee36f
Many imx233 targets boot in a very low performance mode, typically cpu and
dram at 24MHz. This results in very slow boots and very unstable USB
bootloader mode. Since cpu frequency scaling is disabled in bootloader in
rockbox, always make the frequency scaling code available and boost at boot
time.
Change-Id: Ie96623c00f7c4cd9a377b84dcb14b772558cfa4d
This one is a bit strange: our codebase just don't use it if there is both
SD and MMC, so this missing function got unnoticed so far.
Change-Id: Ifea4bb5140477b7637d033737594259cc44fb10e
The i2c core has some bugs: it locks up when the slave doesn't NAK and
prevent the dma channel from being resetted. Specifically handle this
situation by setting CLR_GOT_A_NAK (workaround) and then reset dma and i2c
block.
Change-Id: I0e09d38d4301a0ad42dfad785cc934b43f2c4485
Target that have a touchpad/touchscreen should disable it while
being locked (In order to avoid LCD to drain battery power due to
"key locked" constant reporting messages. If they a have a keylock
button this was already handled at driver level. If not (e.g. fuze+),
they will have to implement a switch at driver level that action.c
can operate on softlock.
This patch does the following for any target having a touchpad
or a touchscreen and no HAS_BUTTON_HOLD (ie any softlock target)
1) it implements the code to call button_enable_touch(bool en) in
action.c.
2) button_enable_touch is implemented in button.c and call
either touchpad_enable or touchscreen_enable
3) those two function are implemented respectively in touchscreen.c
and a new touchpad.c file. They provide a generic way to silents touch's
device and call a function at driver level where target specific code
can be implemented if possible/needed (for power saving for instance).
Those function name are touchpad_enable_device and touchscreen_enable_device
4) we implement an empty function at driver level of targets that need it
to have them still being able to compiled.
Change-Id: I9ead78a25bd33466a8533f5b9f259b395cb5ce49
Reviewed-on: http://gerrit.rockbox.org/569
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Drop most of the cases: only keep 64 MHz and 133 MHz. Pick values
from the manual which seem to match real life values.
Change-Id: I912752fbe372f9f44207db6853d0ff92fd619bed
Now that the drive strength problem has been fixed, we can safely
drive sd cards at 48MHz in HS mode to get the best possible
transfer speed at 3.3V.
Change-Id: I0291589c399fb4880deba97895ff578451a32f99
Instead of going back and forth between TRAN and STBY modes,
stay in TRAN mode all the time, this avoid two commands on each
read/write and a potential delay to wait for the card.
Change-Id: Iafd456ab9a581d870331b622eeb48dcc254eda7f
This allows tells the card the number of blocks that will be
transfered. This is usually faster than continuous read/write.
It is mandatory for MMC and on SD cards, support is probed.
Change-Id: Ide3f97c26c2b714390884c69e05b00c2caa552f8
The old max dma transfer size was set to 2^15 because allowing
values up to 2^16 would result in overflow of the transfer count
in many places. This was a problem with the old register headers
because the macros didn't make sure the result is contained in
the bitmask of the field. The new macro do so 2^16 will actually
end up being 0 which means 2^16 for the hardware. This is kind of
hacky but it works and I prefer that this stays a power of two
because setting it to 2^16-1 would be extremely weird.
Change-Id: I9ce5661c477a79ab52efd5c573948e2353117804
- take advantage of the new rmi power function implemented to:
1) lower usual power_mode to low_power as it seems to be enough and might save
some battery
2) implement a system that lower that state to very_low_power
after 1 minute of inactivity.
3) implement touchdev_enable(bool) that can be use later to disable the
touchpad when needed
4) improve the debug screen report of the current power state and
changing the power state using volume keys
Change-Id: I0b372696d4b2bef5360c778d0500870fd9badee1
Reviewed-on: http://gerrit.rockbox.org/525
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
When using variadic macros there's no need for IF_MD2/IF_MV2 to deal
with function parameters. IF_MD/IF_MV are enough.
Throw in IF_MD_DRV/ID_MV_VOL that return the parameter if MD/MV, or 0
if not.
Change-Id: I7605e6039f3be19cb47110c84dcb3c5516f2c3eb
These nearly identical files are multiplying like rabbits as PP targets
are added and make SoC-related changes a PITA. Just include the master
.lds file from the target one as was done for bootloader USB.
Change-Id: I65e9e653030f0688b1728e32ada16abf2932e029
The old code used get_action which is bad because it belongs to
apps/. Instead rewrite a simple version of get_action, also
rewrite the top level handler. Since the number of screens is
becoming quite high, it now shows a list and the user can start
from any screen. Once in a screen and as long as the user presses
select, it will advance to next screen until it finally returns
to the list on cancellation.
Change-Id: Icbc7676a17e4a6e859b7781a4a471d8303910591
The current code was spreaded over power and powermgmt which made
it behave strangely, especially since there are relationships
between power management and frequency scaling. The new code makes
sure power management is initialised before frequency scaling
starts. It also makes sure to start from a known state, thus
fixing potential issue when the bootloader stops in a trickle
state where DCDC is improperly configured.
Change-Id: Ibded2e590e108f6c98daa52d2cf1bd28763c8923
Implement the switch function as specified by the specification,
that is wait for the response AND transfer 64 bytes of data. This
fixes some issue when the SD card take a long time to switch. In
particular waiting 100ms (max per spec) will not work if no data
is transfered in some cases.
Change-Id: Ia22350468018b842e57ce6f6c1a8d676eba97fb8
