- Revert BUTTON_HOME
- Modifications to SD driver (µSD not working yet)
TODO: µSD and FM radio
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@27492 a1c6a512-1295-4272-9138-f99709370657
Show all the adc channels in the IO ports debug menu (not for as3525v2
since the channels are different)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26149 a1c6a512-1295-4272-9138-f99709370657
This is to a) to cleanup firmware/common and firmware/include a bit, but also b) for Rockbox as an application which should use the host system's c library and headers, separating makes it easy to exclude our files from the build.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25850 a1c6a512-1295-4272-9138-f99709370657
the arm926-ejs doesn't have synchronous/asynchronous/fastbus modes, so
just change CGU_PROC directly
Note: we could use a lower unboosted frequency now
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25417 a1c6a512-1295-4272-9138-f99709370657
Move CLKDIV macros into clock-target.h.
Only enable the necessary interfaces for the 3 clock registers used for SD.
Add MEMSTICK and SDSLOT registers to bottom of register display in View HW info debug page.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25309 a1c6a512-1295-4272-9138-f99709370657
The registers value does not change so we don't need to read them
This avoids dividing by 0
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25303 a1c6a512-1295-4272-9138-f99709370657
calc_freq(CLK_PLLA) for as3525v2 simply returns 240MHz instead of calculating until we understand how it is calculated.
Now displays 922T or 926ejs depending on version.
Remove SD and uSD info from as3525v2 as it is not useful due to different SD controller.
Increased the lines used for each page of display on clip screen size.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25120 a1c6a512-1295-4272-9138-f99709370657
This gets rid of LCD glitches on Sansa Fuze, and now LCD transfers can
get interrupted by button reading
Flyspray: FS #10603
Author: Bertrik Sikken
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24192 a1c6a512-1295-4272-9138-f99709370657
This patch changes all references/assumptions of PCLK to IDE_CLK for the internal pl180 controller.
Lower the AS3525_IDE_FREQ to 50 MHz in order to be able to divide by 2 for 25 MHz on the internal SD card.
Adjust the code in debug-as3525.c to account for the change and the frequencies reported should be correct.
Add some #if defined(HAVE_MULTIDRIVE) conditionals to cut out the code dealing with uSD for the clip.
Isolate the write delay needed for low frequency writes to only run for standard speed uSD cards. That is the only case for an MCICLK at 15.5 MHz.
Internal cards run at 25 MHz, HS uSD at 31 MHz, and standard speed uSD cards at 15.5 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23929 a1c6a512-1295-4272-9138-f99709370657
If the controllers were already enabled there was a chance we could try to read the MCI_CLOCK registers while the cards were buffering and then disable the controllers prematurely.
I guess funman knows and sees all!! Thanks funman.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23811 a1c6a512-1295-4272-9138-f99709370657
Because we turn off the clocks to the SD controllers between disk accesses we were unable to read the MCI_CLOCK registers until there was a disk access. Now we can read them immediately.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23810 a1c6a512-1295-4272-9138-f99709370657
Adjust SD timeouts accordingly.
Adjust code in debug-as3525.c to display correct frequencies on system/debug/View disk info page.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23350 a1c6a512-1295-4272-9138-f99709370657
of 400 khz Ident freq. Also misc formatting changes.
Displaying the 400 khz ident frequency for the SD and uSD cards was not really
useful information. This change displays the MCICLK frequency that we are
running the cards at. The page now displays 0MHz until a card access and then
will displays the set frequency and the actual frequency. The uSD display is
now only displayed for those players with a uSD
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@22684 a1c6a512-1295-4272-9138-f99709370657
Lower CVDD core voltage to 1.10 volts when the frequency is less than 200 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@21577 a1c6a512-1295-4272-9138-f99709370657
- Indentation fix
- Put braces around _DEBUG_PRINTF macro
- read_cp15() is only 1 instruction so inline it, and it doesn't access memory
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@21477 a1c6a512-1295-4272-9138-f99709370657
Don't read the buttons from GPIOC but from DBOP_DIN (all directional buttons + select)
Still missing hold, rec, volume up and volume down
Read microsd
Tuner is a si4700 but seems to suffer from the same problem than e200v2
Sound works
TODO: missing buttons, lcd yuv, test lcd performance (the c200v1 lcd performance has decreased since r21321 : needs to be investigated)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@21330 a1c6a512-1295-4272-9138-f99709370657
With a few modifications by me:
Return 0MHz for PLL disabled (PLLB)
Mention if i2si and i2so are on or off
Simplify scrolling (for small & large displays)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@20987 a1c6a512-1295-4272-9138-f99709370657
Implement some of the new functions
Use as3514 rtc
Add AS3525 case in rolo.c
Copy card_get_info_target() from ata-sd-pp.c , and use the correct 32bits words order
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@19064 a1c6a512-1295-4272-9138-f99709370657
