Power management is somewhat different on stmp3700 which doesn't
have the 4.2V rail and completely different on stmp3600 which has
several DCDC. Currently only handle imx233.
Change-Id: Ic7815141286117b74022ffc53cfa48664fd7faac
Using the ssp macros, we can easily handle the stmp3600 which
has a single ssp block. Take care of all the nasty differences
between targets like bus width
Change-Id: If98a091cc262e9e6834f6fb9826f7c5515bfe621
Currently don't do anything on stmp3600 because emi is completely
different. On stmp3700 it is unsure how the pll lock is handled
and this will need more testing.
Change-Id: I3d11282531f54f2ecc4187c0d913e2c61f4de14d
Add finer granularity to start command: now commands can be
prepared, schedule and semaphore increased independently.
Change-Id: Ib1ed1f20f4b46dc61b6dbab6ddec8b54e3d832b9
Factorise pin setup, rewrite PIO code, add support for lcdif irq,
handle all the various differences between the stmps, drop yuv
blitting code since it already exists in the common lcd drivers.
Change-Id: Ifc40aed9b3b12f16611ce960602e46a5bc87ae53
The lradc architecture of the stmp3600 is rather different:
only channels 6 and 7 have configurable source and we need to
take care when allocating channels so that we can actually
measure the right channel! Delegate die temperature sensing to
the power block on stmp3600.
Change-Id: I0860eb4ea98240facc3d4a19d61684eca5f630cc
There are many small differences between them. In particular
some regulators are not available on stmp3600. Also the vbusvalid
detect method is not available as an irq on stmp3600 and seems
broken on stmp3700. Finally die temperature is handled by the
power block on stmp3600.
Change-Id: I2c68b418738f15564e445d3a1496018cef97fff7
Under some circumstance (timeout), the dma interrupt is not fired
and only the error one is. This can happen with some picky SD
cards and with the current code it causes a 1 second timeout.
This code properly catches the error interrupt to stop as soon
as possible.
Change-Id: I9c53ea272d01793f0f229571502e99eb62f1b723
The current pwm interface is too low-level. Introduce a higher
level setup function which directly computes the parameters from
the required frequency.
Change-Id: Ie95c7522e9f42492fe872203f4cab46770a9649a
The clkctrl functions were becoming a mess. Normalise the names,
get rid of the xtal derived as special case and use the same
interface.
Change-Id: Ib954a8d30a6bd691914b5e0d97774ec9fc560c50
A number of pins on the imx233 are standard and manually calling
functions to acquire, set function/drive/output is painful. This
will become unmanageable when we will add support for the other
stmp chips.
Introduce the concept of virtual pin which is a way to completely
describe a virtual pin (virtual because pins are muxed).
Change-Id: I01b6e040945648e58e1d1abab06529c9571c5f10
The current pinctrl functions were a mess. Normalise the functions
names to make them shorter and clearer.
Change-Id: Iac6ff84625ef2b7610268e3a5802dc0088de3167
The code assumes that gustable[] has 128 entries, while it
only had 120. Since the entries follow a simple pattern (they
seem to be note frequencies, so each entry is the previous one
multiplied by the 2^(1/12)), expanding the table is the simple
fix.
Change-Id: If5b5a50378afd3206c9d550227dd9aac8e355c96
The SD SWITCH command has a result and can take a long time to
finish. Ignoring the answer and waiting an arbitrary time is
unreliable at best.
Change-Id: I1bfbb193952b96598f8bb056bac88220d4edf1fc
Refactor code.
This tool can now either load a scrambled rockbox
firmware (in which case the model is check against the
firmware), or any ELF file. This is useful for example
for hwstub which produces a ELF file and still needs
to be loaded by producing a SB file.
Change-Id: I7aa381b3f6587788d1950793e89ce5608c53cccc
The mkimxboot was becoming messy with juge functions and
redundant code. Factor reading/writing/loading code into smaller
functions. Introduce the concept of rockbox firmware to simplify
support of other formats than scramble.
Change-Id: I3a61295ca5abca1a0eee8c9e8709c6b8dfa256a6
