The FT6x06 driver used for the Shanling Q1's touchscreen
has been extended to report more than one touch point. It
can also return the gesture detected by the controller,
but this doesn't seem to report anything useful on the Q1.
Multi-touch is only useful in 3x3 grid mode since the Rockbox
button API cannot report more than one touch point.
The FiiO M3K uses the same driver so it's been updated to the
multi-touch API, but functionality is unchanged.
Change-Id: I4de42f44808d6eb902e3da212d8f936b7a5042c7
Based on a patch by Amaury Pouly which was based on a patch from Ryan
Hitchman.
I mainly moved the code for polling into the tuner driver so it can be
reused by other targets. I added the CONFIG parameter for the polling
frequency (in ticks) to save energy. Also, I did some minor cleanups.
Change-Id: I95a62e7e1e42c62dbf47ecb27a3b312a42be62aa
We have this nice event library laying around probably a few more places
we could use event callbacks
Change-Id: I9180fa9d78788d161f2587110644ca3e08df6f50
This boosts USB transfer performance a bit, ~10% for reads and
~25% for writes, for large-ish file transfers. Rockbox is still
around 33-50% slower than the OF.
Change-Id: I236a1e5c69a290c47ed27b70cb2631111fc157ed
All existing USB drivers now define USB_LEGACY_CONTROL_API to
enable the emulation layer.
Control request handlers will be ported in follow-up commits.
Change-Id: I4be1ce7c372f2f6fee5978a4858c841b72e77405
This makes it possible for macros of conditionally included string
descriptors to get a correct index no matter what other usb drivers
are enabled or disabled due to the nature behavior of enums.
Change-Id: I8ccebbd316605bed0f5d90b6b73fab4a333c02fa
Upon getting a USB reset, the USB core will update charging
current by calling usb_charging_maxcurrent_change(). On all
current X1000 targets this may cause a hang, since changing
the charge current involves a blocking I2C transaction.
Eg. if the host issues a reset when we're already configured
as part of error recovery, the change from 500 mA -> 100 mA
will cause a hang.
Change-Id: I5b45272c01fa16b179ae3d16bbc50c7fab9a416b
IMHO the current name is somewhat misleading:
- usb_drv_send() is blocking and we have usb_drv_send_nonblocking()
for the non-blocking case. This inconsistent naming can only
promote confusion. (And what would we call a blocking receive?)
- Other hardware abstraction APIs in Rockbox are usually blocking:
storage, LCD, backlight, audio... in other words, blocking is the
default expected behavior, with non-blocking calls being a rarity.
Change-Id: I05b41088d09eab582697674f4f06fdca0c8950af
A reasonable default assumption for a user
would be that they can plug their device into
a USB AC adapter and it will charge with as much
current as it reasonably can. With the previous
default, an AC adapter will only do 100mA, basically
a trickle charge.
Make this configurable default per-device, so as not
to break old devices without testing.
Define TARGET_USB_CHARGING_DEFAULT to USB_CHARGING_FORCE
to use the new default.
Tested on both erosQ Native and M3K.
Change-Id: I77265d356a41d67357ebc6e9f7e0c25a37b74931
Set the maximum volume on both hosted and native ports
to -2 dB.
Verified behavior here on native and by borkitall on irc
for hosted.
Change-Id: I3aebc2bb4b9294a4137a33694c83139c0d76099a
It's not yet working and because all storage is removable (and the OF
works fine) it's of limited utility aynway.
Change-Id: I8a6a59ac16503d0f4574c3934f473cac54e86858
It has only a couple GB of onboard flash storage with no storage
driver in Rockbox. It hasn't seen any meaningful development since
its initial commit, it's not on the build farm, and the bootloader
build is broken by other refactoring.
Change-Id: Idd9e3c46fac9b96f416ce444182f97a50770e747
Similar to the native port, the hosted port benefits from
adding a -1 dc bias to the PCM data. This prevents almost
all clicking artifacts.
Change-Id: Ic6378716774b6d88df23c476e2ef54d49f33dc72
A small negative offset seems to silence all
play/pause clicking on the PCM5102A.
Also adding PCM soft muting, and muting the headphone amp
when the headphones are detected as removed. This has been
tested to not cause any unintended side effects on the
line out.
Also confirmed the numerical dB values are (approx.) correct.
Change-Id: I689d68887c86add9cc5e0ccb0c7de01aaa69b4d9
* It had a (read) buffer overflow when dumping the stuff on the back half of the buffer
* a highly questionable code construct was nuked
Change-Id: I7f6f119524fc2095f788fc9b3d356459955d3ace
What works:
- LCD: 16-bit RGB565
- all buttons, including scrollwheel
- SD Card
- Battery level and charging/not charging status
- USB
- audio
- sample rate switching
- HP / LO detect, with "safe" fixed LO volume -
LO volume will only be put to user-defined max volume
if headphones are not present.
- rtc
- Plugins build, tried a couple and they seem OK
- Bootloader, installable to nand via usbboot
What doesn't work:
- Dual Boot
- power on/off has intermittent, low volume audio click
(sometimes it's completely silent, sometimes there's
a click)
- Audio uses 16-bit volume scaling, so clicking/popping
is pretty bad at lower volumes - need 32 bit volume
scaling, 24 bit I2S data
- USB HID keys not yet defined
- no jztool support
Unknowns:
- Stereo Switch pins: Direction select, AC_DC
(probably not even hooked up)
- What is the actual purpose of the Stereo Swtich?
- How does the bluetooth module connect?
"Someday" stuff:
- get LCD working at higher bit depth
- Bluetooth
Change-Id: I70dda8fc092c6e3f4352f2245e4164193f803c33
I'm not happy with the proliferation of filter-roll-off options
but I don't have a less ugly solution.
Change-Id: I740fca006fa0c3443a467acfea55b6574d48346b
- Audio playback works
- Touchscreen and buttons work
- Bootloader works and is capable of dual boot
- Plugins are working
- Cabbiev2 theme has been ported
- Stable for general usage
Thanks to Marc Aarts for porting Cabbiev2 and plugin bitmaps.
There's a few minor known issues:
- Bootloader must be installed manually using 'usbboot' as there is
no support in jztool yet.
- Keymaps may be lacking, need further testing and feedback.
- Some plugins may not be fully adapted to the screen size and could
benefit from further tweaking.
- LCD shows abnormal effects under some circumstances: for example,
after viewing a mostly black screen an afterimage appears briefly
when going back to a brightly-lit screen. Sudden power-off without
proper shutdown of the backlight causes a "dissolving" effect.
- CW2015 battery reporting driver is buggy, and disabled for now.
Battery reporting is currently voltage-based using the AXP192.
Change-Id: I635e83f02a880192c5a82cb0861ad3a61c137c3a
Atmel AT88SC6416C CryptoMemory is almost I2C compatible. The device
is connected to bitbanged I2C bus shared with compliant I2C devices.
Change-Id: Iec54702db1bdfb93c01291eef18ec60391c63b16
Do not introduce any change for M:Robe 500 as it uses the two LCD frames
in non-obvious way.
Sansa Connect and Creative ZVM use only single front framebuffer.
Place TTB at DRAM end to minimize memory loss due to alignment.
Reserve as little as possible memory for the LCD frames.
On Sansa Connect this change extends audio buffer by 858 KiB.
Change-Id: I21bdeec4cfba86d71803a39acd651a87e73767e6
This eliminates the dependence on a special struct since we were only
using the modtime anyway. But it no longer fits any known standard APIs
so I have converted it to our own extension instead. This can still be
adapted to existing hosted APIs if the need arises.
Change-Id: Ic8800698ddfd3a1a48b7cf921c0d0f865302d034
This emulates the traditional utime function from UNIX clones to allow
for manual updates of the modification timestamp on files and directories.
This should only prove useful for non-native targets as those usually
have a libc version of utime.
Change-Id: Iea8a1d328e78b92c400d3354ee80689c7cf53af8
Make it possible for target to provide voltage, percentage and time to
empty values. The voltage measurement is nice to have in debug menu even
if the actions are taken only based on percentage. Perform battery level
estimation based on voltage only if percentage is not available.
Use time to empty based on actual power consumption. This makes the
estimated runtime displayed in Rockbox Info to react to backlight
setting. The bq27000 updates time to empty estimate every 5.12 seconds
so it is possible to see the estimate with backlight off on the screen
if user enters Rockbox Info, activates hold switch, waits 11 seconds and
releases the hold switch.
Change-Id: Iafe3fa0fb334e3428e3a0ad05b2c020d208dc934
Prevent startup screen flash by properly using AVR LCM functions. Power
off LCD when not needed to improve battery runtime.
Change-Id: I76e3c5c0208774f189fbc6f7d7b3c9e22c062285
Import non-free firmware image from linux-firmware package.
Firmware loading works but is disabled at compile time because just
loading firmware without configuring device results in higher power
consumption without any benefit to end user.
Change-Id: I8fd252c49385ede1ea4e0f9b1e29adeb331ab8ae
This moves the time conversion function to timefuncs since it has
uses on ports that don't use the FAT driver. This function has no
dependency on the FAT driver as it is so this should not cause any
issues. To reflect this separation the function was renamed to
dostime_mktime since it is really for DOS timestamps. The places
where it was used have also been updated.
Change-Id: Id98b1448d5c6fcda286846e1d2c736db682bfb52
Use 32-bit monotime AVR counter for time tracking. Set the time by
adding fixed offset to the counter value. Store the offset in rockbox
directory to make it persistent between reboots.
Do not implement alarm functionality as wakeup is only possible from
sleep and not from complete power off.
Change-Id: I615c7eb4df8ab0619dcbfcff107bc7051a15aace
Consider battery level down to 0 as safe as OF continues to operate
normally even when at level 0.
Change-Id: Ie3889e5662b9fa6588e20ad02d8953f29e28800c
Wait on semaphore until DMA finishes instead of busy waiting. This
allows the CPU to be used by other tasks during transfers.
Increase peripheral clock frequency, divide AHB by 2 instead of 3.
Function clock frequency is AHB divided by MMC divider + 1.
Change-Id: Ic890634da7e3541962ea3501eae8fa2ca2db606a
On devices that can assign interrupt IN, bulk IN and bulk OUT endpoints
this change results in the serial interface working out of the box on
Linux and Windows. On Linux it is registered as ttyACM device and on
Windows it is assigned a COM port number.
On devices that cannot assign the interrupt IN this change won't have
any effect.
Implement minimum required interface control requests. Respond with
whatever line coding was set to make terminal programs happy.
Change-Id: Id7d3899d8546e45d7cb4ecc3fe464908cb59e810
Allows for the i2c boilerplate to be shared between the M3K and
Shanling Q1 ports. M3K-specific quirks remain in button-fiiom3k.
Change-Id: I8879b603cefc16416bb200f1c484ca916d935c6a
Acknowledge SYS_USB_CONNECTED in all queues so USB task can gain
exclusive access to the storage.
Reduce CPPI requeue timeout to speed up disk access.
Change-Id: I322aae4cac679696bb8186ccacf838a18f0715e9
Port USB driver from Sansa Connect Linux kernel sources. The device
successfully enumerates and responds to SCSI commands but actual disk
access does not work. The SCSI response sent to host mentions that both
internal storage and microsd card are not present.
Change-Id: Ic6c07da12382c15c0b069f23a75f7df9765b7525
The old name was a bit misleading. AXP173 is sort of the lowest common
denominator of a series of related chips. The M3K uses an AXP192 which
has a few extra features vs. the AXP173.
New voltage regulator stuff was added for the sake of the Shanling Q1
native port (that player also uses an AXP192).
Change-Id: Id0c162c23094bb03d13fae2d6c332e3047968d6e
Some audiohw API calls are shared between playback and recording,
eg. frequency settings. Implementing these in the DAC driver won't
work for the M3K, as it uses a separate codec for microphone input.
Change-Id: Ieb0a267f8a81b9e2bbf0bbca951c5778f8dcd203
- Add support for skip and seek while the player is locked.
(Thanks to @bahus for the suggestion)
- Fix touch zones because the down button zone ended up being
a lot smaller than expected due to the touchpad's wonkiness.
Also added a visual display of the touchpad to its debug menu.
- Fixes the pictureflow keymap because it was mostly unusable.
Change-Id: Ic0da4f8df3613ff7828ce1cb940ed9e77ada3281
Also bump max battery capacity to 7300mAh, to accomodate
oversized aftermarket units that require case mods.
Change-Id: I743e550b0c0843ab17529e70b5d592ea0e9a79d8
- Move WPS Stop to Power (Hold)
- Add WPS Hotkey to Wheel scroll Fwd/Back
- Add WPS Quickscreen to Play (Hold)
- Add Tree Hotkey to Play (Hold)
Change-Id: Id74622138353521f736c0de1009a354307b108eb
SPL and UCL-compressed bootloader are now packed into one output,
bootloader.m3k, eliminating the separate SPL build phase.
The Rockbox bootloader now has a recovery menu, accessible by
holding VOL+ when booting, that lets you back up, restore, and
update the bootloader from the device.
Change-Id: I642c6e5fb83587a013ab2fbfd1adab439561ced2
It never worked, and hasn't compiled in something like a decade, Given
the HW capabilities (limited onboard flash, no expandability) there's
really no point in trying to fix/complete it.
Change-Id: I7d175089840396f8891645bd10010d730dd5bfdc
They were never finished, never saw any release ever, and haven't
compiled for the better part of a decade. Given their HW capabilities [1],
they are not worth trying to fix.
[1] 1-2MB RAM, ~256MB onboard flash, no expandability
Change-Id: I7b2a5806d687114c22156bb0458d4a10a9734190
Although data transfer is reliable with DMA, it seems to cause hangs
and lockups during the early stages of connection and it's not clear
what the cause might be.
Change-Id: I9a83089c31d28309f0534dcdedf3c8c8348e6e3d
This only required a minor patch to the usb-designware driver due
to DMA requiring physical addresses -- on the X1000, these differ
from virtual addresses so we have to do the usual conversion.
Both the mass storage and HID drivers work, but there are a few
issues so this can't be considered 100% stable yet.
- Mass storage might not be detected properly on insertion,
and USB has to be replugged before it shows up
- HID driver may occasionally panic or hang the machine
Change-Id: Ia3ce7591d5928ec7cbca7953abfef01bdbd873ef
- Added register names to reduce usage of magic numbers
- Added function to control max charging current, needed for USB
- Corrected comment about axp173, since FiiO M3K has an axp192
Change-Id: I6604ce8d44e5a2ee84061cf042d17ccc4734ac57
After conducting some simplistic tests, I found that the power usage
did not appear to be affected by the CPU frequency.
I tested by playing back a 44.1 KHz FLAC file on single track repeat,
and measured current with the AXP173's battery discharge current ADC.
The button and LCD backlights were set to always on. Headphones were
unplugged and the volume was muted to eliminate any influence from
the headphone amp.
On average the current usage was between 78-81 mA at 1008 MHz, 252 MHz,
and 112 MHz. If anything, 1008 MHz drew _less_ current than the lower
frequencies, by about 1-3 mA.
A possible explanation for this, assuming it's not just a bias of the
test, is that the CPU idle state saves so much power that it's better
to maximize the real time that the CPU spends idling. More systematic
testing is needed to confirm this.
Change-Id: I527473e8c4c12bc1e94f8d4e849fecc108022abe
Tested on eros q, everything measured from line out,
open circuit.
- volume steps were approximately double the dB they
were labelled as, so "-2 dB" would result in a change
of about -4 dB from maximum (0, +6.2dBV)
- maximum volume defining the line out volume only
changed every 10 values, and then was not close
to correct- "-10 dB" resulted in -2.5 dB from maximum
This gets the volume dB approximately correct, and
maximum volume correctly sets the line out volume.
I was unable to get odd values in the max volume
to work, so set the step size to 2 instead of one.
For "consumer level" (-10dBV), set to -16.
For "Pro level" (+4dBu -> ~1.8dBV), set to -4.
Change-Id: I898b85d768153579a893b23551019af88f865d21
Including direct use of the external SD card mount
Known issue: If SD card is inserted at startup, it must be
ejected and reinserted to be registered.
Change-Id: I5f420160bda32135cbb088c1e8b04b6e3a73018e
(Don't include rbpaths.h in settings.h, or string-extra.h in rbpaths.h)
Build-tested on rocker, erosq, mini2g, nano2g,
xduoox3, clipzip, dx50, and uisim
Change-Id: If32e9c9910f5c8247a655cb64522b84d6d7ccbb5
There is already a sound_numdecimals() function, according to Git
it's been around since 2005. No need to add another one :).
This reverts commit 92a0ab8789.
Change-Id: I533ebf1763dd7a27346842982493d4550f05ad7c
Ensure the default setting reflects what the service manual says the
official battery capacity is. Change the ranges to reflect what
replacement batteries are actually available.
This range is actually much shorter in reality due to these units
requiring the rarer 3 pin battery type that uses a thermistor. As such
there's only one real replacement battery for each.
So the HDD1630 caps out around 700 mah while the HDD6330 caps out around
680 mah.
Change-Id: I2dbbba83ad2cd6e1d84e3481c4af84a06c45e16b
This appears to finally fix the issue
turns out the status register we were writing was only for the CPU
COP cache flush wiped out the CPU cache
--
Added some defines to cut down on the magic numbers
Added some comments explaining such
Set the address to full 20 bit address
0x1FFFFF which is then left shifted 11 internally -- somewhere around 4GB?
Link explains the cache status bits
https://daniel.haxx.se/sansa/memory_controller.txt
Change-Id: I57b7187c2f71a5b54ce145bf3a21ed492a8993cb
This uses the new unicode string literal feature that is available
now to greatly simplify the initialization of these special string
types. This makes them much more readable at a quick glance.
Change-Id: Iad8b49aa763486608e3bb7e83fb8abfb48ce0a7b
-- apparenty 0x4 aligned doesn't work properly
requires 0x8 alignment at least for the h10 20gb
but enabled for all processors that define MEM_ALIGN_ATTR
Change-Id: I11edaab183b91a6d158f1f439f173b9b699dc914
This allows the user to make use of the DAC's power-saving abilities.
The two modes are "high performance" and "battery saver". This feature
is supported by the AK4376 DAC in the upcoming FiiO M3K port.
The setting is only a manual toggle right now, but in the future it
could be hooked up to the battery level (via another setting) so it
can be toggled automatically when the battery gets too low.
Change-Id: I482af6e2f969fcbdeb3411bd3ff91f866b12d027
It's possible to get up to 3000mAh batteries for this device, although
it requires that you use an iFlash adapter to make enough space.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Change-Id: I0d0d02aa30caffcae4a7e8c805516a1266eef359
affects all hiby targets, fiiom3k, and ibasso dx50/dx90
As well as deduplicating a small pile of code, this also implements
hysteresis so we're not doing a sysfs read/lookup multiple times
back-to-back every time the power management tick fires.
Change-Id: I2f7672acbb36341becf67e07960c24c681270d09
This means we will no longer send them routinely and instead rely on
the HID driver to send them when the host requests it. This also
moves the reporting out of the power management code where it probably
did not belong in the first place.
Change-Id: I9c8420e81897f1f6caaa55ffacc7525589f1ef75
This allows rockbox to report its battery status through the
HID Battery Strength method that is available through the
Device Controls usage page.
Change-Id: Ia7a7dd9b9d476dd9df5a5f5becabc5ae823e9a89
- The range-based cache operations on MIPS were broken and only worked
properly when BOTH the address and size were multiples of the cache
line size. If this was not the case, the last cache line of the range
would not be touched!
Fix is to align start/end pointers to cache lines before iterating.
- To my knowledge all MIPS processors have a cache, so I enabled
HAVE_CPU_CACHE_ALIGN by default. This also allows mmu-mips.c to use
the CACHEALIGN_UP/DOWN macros.
- Make jz4760/system-target.h define its cache line size properly.
Change-Id: I1fcd04a59791daa233b9699f04d5ac1cc6bacee7
Basically no longer treat SCROLL_FWD/BACK as "button" events, instead
relying on the scrollwheel hooks to handle things properly.
Change-Id: I9bf18595ab3ca68e912f6dfb1f2eac2544578e73
* Bump internal mix buffer size by 4x, to 1K frames (matching ALSA period)
* Handle an underrun that occurs when filling the audio buffer
* Log underruns and make them available in the debug info
Change-Id: I28d56dd35d88851fa167ad92368a5882937a758f
This removes all the pre-release bootloader of version 7 and
replaces them with production releases of version 8. The
pre-releases have their own problems and should be left
behind as they were never officially released.
Change-Id: If96531ba63cf4401d04133bda94735fe94ae4de1
v3: Add in config option
v4: Bugfixes
v5: Force a redraw upon exiting
v6: keypress-in-chargeonly mode enables mass storage (and vice versa)
v7: Fix bootloader builds
v8: Update manual, and have bootloader respect keypresses
v9: Change default to mass storage (ie no change in behavior)
todo:
* test-build dx50/dx90
* Switch from yes/no to proper menu?
* prevent WPS progress bar from drawing over us
Change-Id: I82e0ccb08497b7a5aa756ce77f1332ee963703a7
...
Change-Id: I7946cf240b18a4fa8ace5e25e1eb6e97b8b12d7c
* pcm_get_bytes_remaining()
* pcm_calculate_peaks()
* pcm_get_peak_buffer()
Nothing in-tree uses these at all (except for the lua plugin wrapper)
Change-Id: I971b7beed6760250c8b1ce58f401a601e1e2d585
