Remove the battery power ADC since it's not used right now,
and seems to fluctuate too rapidly to be of much use.
Change-Id: If115e4e3ce14d4c18ce899f5a889f7f99ab66489
This caused LCD problems on the ErosQ, where the screen would
go white until being put through a sleep/wake cycle. The exact
reason for this isn't obvious, but the problem didn't exist
prior to the AXP driver rewrite.
The two dependent changes,
42999913ba - x1000: Increase USB current limit to 500 mA at all times
90dd2f84a9 - x1000: Correctly limit USB charging current
ended up bringing the USB charging situation back to where it
was prior to the rewrite, so the cleanest option is to revert
the whole lot.
This reverts commit 42999913ba.
This reverts commit 90dd2f84a9.
This reverts commit 2d89143962.
Change-Id: I1cff2bfdd1b189df14bcf8cce42db725caa470d7
The 100 mA USB current limit added in commit 90dd2f84a9
is a problem when booting with a completely dead battery.
Often 100 mA isn't enough to power the player, never mind
charge the battery, so revert to the old behavior of only
limiting charge current.
Given that the original firmware on these devices isn't
following the USB spec to the letter, it's probably not
worth trying to make Rockbox do so unless and until it
causes a real problem - which hasn't happened yet.
Change-Id: I179a08310c226fe01460680c62fd25fd69079256
The way this was done before was wrong - limiting the charge
current is not enough since the device will draw additional
power to run. Use the AXP192's vbus current limit control to
stay compliant with the USB specification.
Change-Id: I91b84e3480a432e49bec53cf2a17e4e3444404a4
I noticed a few mistakes in the old driver code and it was in
need of an overhaul anyway... I decided to scale things back,
simplify the code and remove most of the debug menus, netting
a nice code size savings.
One new feature is an advanced debug menu which is accessible
by recompiling the code with AXP_EXTRA_DEBUG. It adds quite a
bit of code size and isn't useful other than for development
so it must be manually enabled by editing the source.
Change-Id: I30e17c1194c14823decd726a574ed14451d4cb2d
This reverts commit 6ff1a935b9.
Reason: it created a mismatch between the displayed voltage
and percent since the voltage was unfiltered but percentage
was based off the filtered voltage.
Change-Id: I4cba099f2e1edf0ef7c4e17a32f566aa66f5b933
This allows battery run time to be calculated from the
actual battery usage on the FiiO M3K and Shanling Q1.
This isn't very good for the time being and the estimate
tends to go all over the place due to small variations
in current or voltage.
The Eros Q can support this feature as well, but since
it already has fixed estimates defined and the quality
of the "real time" estimate is low I am not enabling it
there.
Change-Id: Id34a93ee4b7d66f9f7e56ef0f5149f67e8e72039
Remove battery_read_info() which is a simple wrapper
function only used by debug screens. Use the polling
functions directly to save a bit of code size.
Change-Id: I2919f78105bab186f6933dc1823f9fa67fe74f3e
Give iBasso DX50/DX90 empty adc-target.h headers like all
the other hosted targets to avoid special cases.
Change-Id: Iaae15642fdec4ff18bc9ac01245753135128f676
Future-proofing against newer versions of GCC/binutils which
are stricter about the use of 'inline' functions in headers.
Change-Id: Id620812ed340f0d790ba6c5b8b5cb1d700acfbbf
The FT6x06 driver used for the Shanling Q1's touchscreen
has been extended to report more than one touch point. It
can also return the gesture detected by the controller,
but this doesn't seem to report anything useful on the Q1.
Multi-touch is only useful in 3x3 grid mode since the Rockbox
button API cannot report more than one touch point.
The FiiO M3K uses the same driver so it's been updated to the
multi-touch API, but functionality is unchanged.
Change-Id: I4de42f44808d6eb902e3da212d8f936b7a5042c7
Based on a patch by Amaury Pouly which was based on a patch from Ryan
Hitchman.
I mainly moved the code for polling into the tuner driver so it can be
reused by other targets. I added the CONFIG parameter for the polling
frequency (in ticks) to save energy. Also, I did some minor cleanups.
Change-Id: I95a62e7e1e42c62dbf47ecb27a3b312a42be62aa
All three X1000 native targets turned out to have a very
similar boot configuration and used a nearly identical
makefile. Eliminate this duplication by moving the logic
into the main makefile.
Change-Id: I13044b9675c0abd605b8accdb2fee4f54549b020
Appears to return 0 until the axp has (presumably) completed
its first real measurement.
Note about erosq: keep the power_inint() delay large to ensure
nothing breaks in the bootloader for the time being.
Change-Id: I444e858207cc401c42f1e6ceacf067ad543d4ff8
OST timer fix (7a5130a277) causes a boot failure on some units,
the battery voltage reading needs more time to stabilize.
Change-Id: Ic4a9ba90a16fab8ac6d27dbbe7af381f7c810f8f
The battery stabilization delay call seems to need to be
about 170 at minimum now, let's do 190 for safety (+20ms).
Change-Id: Ifd0248891abe827dfcc3e6baf48cc5bef0d0cc1c
It turns out the prescaler fields in OST_CTRL are 2 bits wide,
not 3. The programming manual (as usual) is ambiguous and its
diagram shows 2-bit wide fields, but the bit positions in the
text give a 3-bit wide field. Ingenic's Linux code and my own
testing shows that they are, in fact, 2 bits wide.
This caused the OST2 divisor to be 16 instead of 4; the OST1
divisor was correct. This means that all udelay/mdelay calls
took 4x longer than they should've. After this change the OST2
prescaler will be 4, as intended, and udelay/mdelay calls will
wait for the intended duration.
Change-Id: I2ac0a9190f49b59a840c649bf586131f5f9fde82
Write -1 to AIC_DR to initialize the "last sample"
to -1 in order to prevent power-on clicks.
It appears necessary to completely fill the FIFO,
otherwise I was able to get a click out of it, however
uncommon it was.
Not only does this prevent a click when first
playing a song after power-on, but it also seems to prevent
any click at all when powering on - previously, a small
click may have been heard when first booting.
Change-Id: I2b81c2fa6af9809ef1c354d7a08ca8f9893a7690
Previously it used the last sample, which turns out to be broken.
The AIC appears to send out a random non-zero sample continously
after boot -- probably because the last sample is uninitialized by
the hardware. Disabling playback is supposed to make it send zero
samples irregardless of the LSMP bit according to the docs, but it
doesn't seem to work this way.
- Change eliminates the white noise heard on the M3K after boot.
- Change has no adverse effects on the Q1.
- Leave Eros Q on the old setting since sending zeros exacerbates
clicking due to DAC's automute feature.
Change-Id: I9996793fc34f4475b19700d076b11505353b3836
Adjust the battery scale to be a little better. I've set
the 100% (discharge) point to be where the battery sags to
when it is done charging but still plugged in.
Not quite sure how best to set the charge scale, it's just
equal to the discharge scale for now.
Change-Id: I9a2730c0b2051300af9eeddb4f67164f38a29002
IMHO the current name is somewhat misleading:
- usb_drv_send() is blocking and we have usb_drv_send_nonblocking()
for the non-blocking case. This inconsistent naming can only
promote confusion. (And what would we call a blocking receive?)
- Other hardware abstraction APIs in Rockbox are usually blocking:
storage, LCD, backlight, audio... in other words, blocking is the
default expected behavior, with non-blocking calls being a rarity.
Change-Id: I05b41088d09eab582697674f4f06fdca0c8950af
Fixes backlight not turning on after booting (tested on an iPod Mini 2G).
backlight_hw_init() copied from iPod 4G.
Change-Id: I9c32ca5ecd3dc74ea997e6cb843da79d303b0615
It has only a couple GB of onboard flash storage with no storage
driver in Rockbox. It hasn't seen any meaningful development since
its initial commit, it's not on the build farm, and the bootloader
build is broken by other refactoring.
Change-Id: Idd9e3c46fac9b96f416ce444182f97a50770e747
Similar to the native port, the hosted port benefits from
adding a -1 dc bias to the PCM data. This prevents almost
all clicking artifacts.
Change-Id: Ic6378716774b6d88df23c476e2ef54d49f33dc72
According to backtrace(3) man page, the string returned from
backtrace_symbols() contains the return address so we shouldn't
need to print it ourselves.
Change-Id: Ia779207285c9ea0052b9aee3d84ee8380bf46d82
