| .. |
|
archos/av300
|
Rework ATA driver to get rid of lots of target-specific constants and allow for non-memory-mapped task file registers.
|
2011-01-02 22:51:47 +00:00 |
|
as3525
|
AMSv2 USB: Remove usb_enable call that occurs after core is already initialized and the usb_disable call while in ISR. Also, no point in panicing over a disconnect.
|
2011-02-04 05:46:55 +00:00 |
|
at91sam
|
|
|
|
imx31
|
i.MX31: Now that it matters because there's a debug screeen that allows changing things while running, some DVFS/DPTC stuff has to be done more carefully. Trim out some stuff and group functions better as well.
|
2011-01-23 20:21:35 +00:00 |
|
ipod
|
iPod Nano2g/Classic clickwheel: Configure GPIO pins as Hi-Z while hold switch is engaged
|
2011-02-10 19:13:30 +00:00 |
|
iriver
|
Convert PortalPlayer iRivers to use USB-mode enabled bootloader. The H10 5/6GB already has a pre-boot USB mode (so it's a little redundant there) but building them the same way is simpler.
|
2011-01-17 06:50:27 +00:00 |
|
olympus
|
|
|
|
pbell
|
Get the last warning for vibe 500 bootloader.
|
2011-01-15 09:11:38 +00:00 |
|
philips
|
e200v1 seems to be ok using USB-enabled bootloader. Also, include the bootloader USB .lds into the boot.lds instead of pasting into every one to keep things sane for now-- commented upon inside.
|
2011-01-16 01:40:15 +00:00 |
|
pnx0101
|
|
|
|
s3c2440
|
Rework ATA driver to get rid of lots of target-specific constants and allow for non-memory-mapped task file registers.
|
2011-01-02 22:51:47 +00:00 |
|
s5l8700
|
Remove files accidentally commited in 28953
|
2011-01-03 13:24:27 +00:00 |
|
s5l8702
|
Fix red (remove accidentally committed debugging code)
|
2011-02-10 00:35:46 +00:00 |
|
samsung
|
|
|
|
sandisk
|
Fix r29062 warning.
|
2011-01-16 01:48:15 +00:00 |
|
tatung
|
|
|
|
tcc77x
|
Clean up multiple definitions of RAM size. Remove -DMEM (make) and MEM (code), use the already defined MEMORYSIZE instead.
|
2011-02-02 17:43:32 +00:00 |
|
tcc780x
|
Try to get some control over #ifdef hell in usb.c by refactoring and inline function use. SYS_USB_DISCONNECTED_ACK hasn't been doing anything useful for the USB thread; remove it. USB thread simply ignores that value. Observe only valid usb_state transitions.
|
2011-01-18 14:10:06 +00:00 |
|
tms320dm320
|
M:Robe 500: Use bit modifiers more.
|
2011-02-08 05:53:30 +00:00 |
|
adc-as3514.c
|
|
|
|
adc-pp5020.c
|
|
|
|
ascodec-pp.c
|
|
|
|
ascodec-target.h
|
|
|
|
ata-as-arm.S
|
|
|
|
ata-nand-telechips.c
|
|
|
|
ata-pp5002.c
|
|
|
|
ata-pp5020.c
|
Fix or at least significantly improve FS#11830. With introduction of ATA DMA for PP502x a special treatment of the IDE0_CFG register for the iPod nano (see FS#7510) was lost.
|
2011-01-21 23:32:57 +00:00 |
|
ata-sd-pp.c
|
Try to get some control over #ifdef hell in usb.c by refactoring and inline function use. SYS_USB_DISCONNECTED_ACK hasn't been doing anything useful for the USB thread; remove it. USB thread simply ignores that value. Observe only valid usb_state transitions.
|
2011-01-18 14:10:06 +00:00 |
|
ata-target.h
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
audio-pp.c
|
|
|
|
bits-armv4.S
|
Add ARMv4 16-bit(set, mod, clr) operations used on DM320.
|
2011-02-06 19:43:45 +00:00 |
|
bits-armv6.S
|
|
|
|
boot-pp502x-bl-usb.lds
|
e200v1 seems to be ok using USB-enabled bootloader. Also, include the bootloader USB .lds into the boot.lds instead of pasting into every one to keep things sane for now-- commented upon inside.
|
2011-01-16 01:40:15 +00:00 |
|
crt0-pp-bl.S
|
|
|
|
crt0-pp.S
|
Clean up multiple definitions of RAM size. Remove -DMEM (make) and MEM (code), use the already defined MEMORYSIZE instead.
|
2011-02-02 17:43:32 +00:00 |
|
crt0-pp502x-bl-usb.S
|
Clean up multiple definitions of RAM size. Remove -DMEM (make) and MEM (code), use the already defined MEMORYSIZE instead.
|
2011-02-02 17:43:32 +00:00 |
|
crt0.S
|
|
|
|
debug-pp.c
|
|
|
|
debug-target.h
|
|
|
|
ffs-arm.S
|
|
|
|
i2c-pp.c
|
|
|
|
i2c-telechips.c
|
|
|
|
i2s-pp.c
|
|
|
|
kernel-pp.c
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
lcd-as-memframe.S
|
|
|
|
lcd-c200_c200v2.c
|
|
|
|
lcd-ssd1815.c
|
|
|
|
memcpy-arm.S
|
|
|
|
memmove-arm.S
|
|
|
|
memset-arm.S
|
|
|
|
memset16-arm.S
|
|
|
|
mmu-arm.h
|
|
|
|
mmu-arm.S
|
New port: iPod Classic (also known as iPod 6G/6.5G/7G)
|
2011-01-02 23:16:27 +00:00 |
|
mmu-armv6.S
|
|
|
|
pcm-pp.c
|
|
|
|
pcm-telechips.c
|
|
|
|
powermgmt-ascodec.c
|
|
|
|
sd-pp-target.h
|
|
|
|
support-arm.S
|
|
|
|
system-arm.c
|
|
|
|
system-arm.h
|
Use __builtin_constant_p() to select the best byteswapping method: constant or target optimized. Same macro can then be used for constant values and inits as well as non-constant.
|
2011-01-30 00:58:45 +00:00 |
|
system-pp502x.c
|
Add a higher level USB detection that prevents fraudulent bus resets from causing USB mode to be entered. Enable for SA9200 only at this time. Also, for SA9200, use the bus power GPIO rather than the 'connector inserted' GPIO to detect the cable.
|
2011-01-17 12:24:41 +00:00 |
|
system-pp5002.c
|
|
|
|
system-target.h
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
thread-arm.c
|
New port: iPod Classic (also known as iPod 6G/6.5G/7G)
|
2011-01-02 23:16:27 +00:00 |
|
thread-pp.c
|
Clean up multiple definitions of RAM size. Remove -DMEM (make) and MEM (code), use the already defined MEMORYSIZE instead.
|
2011-02-02 17:43:32 +00:00 |
|
timer-pp.c
|
|
|
|
usb-drv-arc.c
|
Add a higher level USB detection that prevents fraudulent bus resets from causing USB mode to be entered. Enable for SA9200 only at this time. Also, for SA9200, use the bus power GPIO rather than the 'connector inserted' GPIO to detect the cable.
|
2011-01-17 12:24:41 +00:00 |
|
usb-fw-pp502x.c
|
PP502x USB: It seems r29087 introduced additional parasitic current consumption after USB disconnect. So, reinitialize the controller just like at startup when disabling USB, which also happens to fix FS#10719.
|
2011-01-20 06:41:05 +00:00 |
|
usb-fw-pp5002.c
|
Fix r29053 red and a leftover use of 'usb' variable as a bool rather than int in main-pp.c.
|
2011-01-15 08:52:59 +00:00 |
|
usb-s3c6400x.c
|
|
|
|
usb-target.h
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
usb-tcc.c
|
|
|
|
wmcodec-pp.c
|
|
|
|
wmcodec-telechips.c
|
|
|
40e76916cd