Michael Sevakis c541e04632 Gigabeat F/X: ... Allow chaning of touchpad sensitivity in the System settings menu. Some units are dodgey at "Normal" senitivity and some at "High". "High" can make some units difficult to navigate and may even require a settings reset so try it and don't use "High" again if it doesn't work out :-). Defaults to "Normal" which behaves like older builds. git-svn-id: svn://svn.rockbox.org/rockbox/trunk@17656 a1c6a512-1295-4272-9138-f99709370657		2008-05-29 21:27:44 +00:00
..
archos/av300
imx31	Fix a comment since it was very wrong.	2008-05-25 02:43:51 +00:00
ipod	Add the ADC_ACCESSORY channel on the ipod, to allow for accessory detection once we figure that out.	2008-05-29 06:12:08 +00:00
iriver	Targets with HAVE_LCD_ENABLE: Provide a means to receive notifications when the lcd is enabled and the image is refreshed so overlayed drawing can also be refreshed. Chiefly mpegplayer needs this so it can redraw the YUV data after the backlight is turned on while paused or when using 'Set Start Time'.	2008-05-28 10:17:16 +00:00
olympus	Make the H10 bootloader work again. Also fix the same problem that might be affecting other PP bootloaders.	2008-05-04 14:42:53 +00:00
philips	Philips GoGear SA9200 port. Working bootloader and normal builds, including sound. No touchpad now, buttons limited to using vol+/vol-/power for up/down/select. Rockbox USB is enabled since the OF is MTP only...read the warnings on the PortalPlayerUsb wiki page.	2008-05-21 03:55:17 +00:00
pnx0101	Remove wrong usage of '.global'. These symbols are imported, not exported.	2008-04-29 06:47:34 +00:00
s3c2440	Gigabeat F/X:	2008-05-29 21:27:44 +00:00
sandisk	Targets with HAVE_LCD_ENABLE: Provide a means to receive notifications when the lcd is enabled and the image is refreshed so overlayed drawing can also be refreshed. Chiefly mpegplayer needs this so it can redraw the YUV data after the backlight is turned on while paused or when using 'Set Start Time'.	2008-05-28 10:17:16 +00:00
tatung/tpj1022	Do core interrupt masking in a less general fashion and save some instructions to decrease size and speed things up a little bit. Small fix to a few places where interrupts would get enabled again where they shouldn't have been (context switching calls when disabled).	2008-03-26 01:50:41 +00:00
tcc77x	Convert the TCC77x ADC driver to use interrupts - based on the technique used in the SH ADC driver.	2008-05-03 07:49:39 +00:00
tcc780x	Targets with HAVE_LCD_ENABLE: Provide a means to receive notifications when the lcd is enabled and the image is refreshed so overlayed drawing can also be refreshed. Chiefly mpegplayer needs this so it can redraw the YUV data after the backlight is turned on while paused or when using 'Set Start Time'.	2008-05-28 10:17:16 +00:00
tms320dm320	Targets with HAVE_LCD_ENABLE: Provide a means to receive notifications when the lcd is enabled and the image is refreshed so overlayed drawing can also be refreshed. Chiefly mpegplayer needs this so it can redraw the YUV data after the backlight is turned on while paused or when using 'Set Start Time'.	2008-05-28 10:17:16 +00:00
adc-as3514.c	Preparing for the Philips SA9200 part 1. Move the Sansa ADC & ATA drivers up one level.	2008-05-13 01:53:19 +00:00
adc-pp5020.c	make mrobe100 work again	2008-02-10 16:06:01 +00:00
ata-as-arm.S	1) Use a separate config-<target>.h for Zen Vision(:M) (60GB)	2008-05-14 18:55:19 +00:00
ata-pp5002.c
ata-pp5020.c
ata-sd-pp.c	Philips GoGear SA9200 port. Working bootloader and normal builds, including sound. No touchpad now, buttons limited to using vol+/vol-/power for up/down/select. Rockbox USB is enabled since the OF is MTP only...read the warnings on the PortalPlayerUsb wiki page.	2008-05-21 03:55:17 +00:00
ata-sd-target.h	Preparing for the Philips SA9200 part 2. Since the SA9200 doesn't have a microsd card (no hotswap), use HAVE_ATA_SD for the Sansa flash driver so we don't rely on HAVE_HOTSWAP in some places.	2008-05-13 02:50:31 +00:00
ata-target.h
audio-pp.c
crt0-pp-bl.S	Enable dualcore for the pp5002 processor by adding the needed cache handling and sleep/wakeup sync to the kernel. Refine some handling of fw/bl startup for all.	2007-11-27 01:20:26 +00:00
crt0-pp.S	Remove wrong usage of '.global'. These symbols are imported, not exported.	2008-04-29 06:47:34 +00:00
ffs-arm.S	Add a complete priority inheritance implementation to the scheduler (all mutex ownership and queue_send calls are inheritable). Priorities are differential so that dispatch depends on the runnable range of priorities. Codec priority can therefore be raised in small steps (pcmbuf updated to enable). Simplify the kernel functions to ease implementation and use the same kernel.c for both sim and target (I'm tired of maintaining two ;_). 1) Not sure if a minor audio break at first buffering issue will exist on large-sector disks (the main mutex speed issue was genuinely resolved earlier). At this point it's best dealt with at the buffering level. It seems a larger filechunk could be used again. 2) Perhaps 64-bit sims will have some minor issues (finicky) but a backroll of the code of concern there is a 5-minute job. All kernel objects become incompatible so a full rebuild and update is needed.	2008-03-25 02:34:12 +00:00
i2c-pp.c	Philips GoGear SA9200 port. Working bootloader and normal builds, including sound. No touchpad now, buttons limited to using vol+/vol-/power for up/down/select. Rockbox USB is enabled since the OF is MTP only...read the warnings on the PortalPlayerUsb wiki page.	2008-05-21 03:55:17 +00:00
i2c-telechips.c	Fixed prototype of i2c_write for plugins and for i2c-telechips (fix red/yellow).	2008-04-28 14:33:03 +00:00
i2s-pp.c	Update source files to include the header file for the functions they implement, to make sure the header and the implementation is consistent (and fix it for a case where it wasn't).	2008-04-28 10:22:05 +00:00
lcd-as-memframe.S
memcpy-arm.S
memmove-arm.S
memset-arm.S
memset16-arm.S
mmu-arm.c	Fix the ARM assembly to ensure that the stack is not used.	2008-05-10 18:30:46 +00:00
mmu-arm.h	This is a big chunk of code necessary to prepare for Gigabeat F flash loading and and implementation of rolo. There should be no noticible changes for the user. A new bootloader is not needed.	2008-04-22 04:34:25 +00:00
pcm-pp.c	Update source files to include the header file for the functions they implement, to make sure the header and the implementation is consistent (and fix it for a case where it wasn't).	2008-04-28 10:22:05 +00:00
system-arm.h	Optimized byte-swapping macros for ARMv6.	2008-04-16 20:44:10 +00:00
system-pp502x.c	Philips GoGear SA9200 port. Working bootloader and normal builds, including sound. No touchpad now, buttons limited to using vol+/vol-/power for up/down/select. Rockbox USB is enabled since the OF is MTP only...read the warnings on the PortalPlayerUsb wiki page.	2008-05-21 03:55:17 +00:00
system-pp5002.c	Enable dualcore for the pp5002 processor by adding the needed cache handling and sleep/wakeup sync to the kernel. Refine some handling of fw/bl startup for all.	2007-11-27 01:20:26 +00:00
system-target.h	Fix freezing of some builds on PP5002. The PP5002 needs the not-sleep-at 0xNNNNNNN0-addresses fix everywhere when caching is enabled, not only in core_sleep(). Introduced a pair of inline functions to sleep and wake cores on PP for consistency.	2008-04-20 17:53:05 +00:00
usb-drv-arc.c	Convert the whole codebase to UTF-8, except docs/COMMITTERS and tools/creative.c, which need checking.	2008-05-05 10:32:46 +00:00
usb-fw-pp502x.c	Philips GoGear SA9200 port. Working bootloader and normal builds, including sound. No touchpad now, buttons limited to using vol+/vol-/power for up/down/select. Rockbox USB is enabled since the OF is MTP only...read the warnings on the PortalPlayerUsb wiki page.	2008-05-21 03:55:17 +00:00
usb-fw-pp5002.c
usb-target.h
wmcodec-pp.c	Do some crackdown on kernel object reinitialization after they could be in use and use before initialization. For c200/e200: Be sure fat cache and ata locks are acquired in the proper order during hot swapping. Delay hotswap monitoring until after initial file mounting (address 2nd kobj concern + possible call of fat driver before init).	2008-03-12 10:03:52 +00:00
wmcodec-telechips.c	More static / header file cleanup.	2008-05-03 23:18:56 +00:00