The power management code was erroneously shuting down the 4.2V rail
when charging is complete. This resulted in the DCDC draining the battery
and thus the battery discharging with USB plugged...
The new code keeps the 4.2V rail active so that battery remains untouched
once charge is complete.
Change-Id: I36e8d31e8115c12ce813c939c5d7bbf2c3490157
NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
- Speed auto detection is launched when an accessory is inserted,
so the user doesn't need to modify settings to use accessories
that operates at different speeds (or when the same accessory is
unplugged and plugged again).
- UART controller is disabled when no accessory is inserted, not
much powersave but everything counts.
Change-Id: If20c3617c2a87b6277fd7e0270031030c44fa953
Since the stub code is shared with NWZ-360, it enables the pullup for the
hold button, but the NWZ-370/380 doesn't have a hold button so don't compile
this code in, it could potentially have unexpected effets or increase consumption
Change-Id: I28c8aa40fc7f9373593ff105fb6df557a6f57ccd
This change ensures that Sansa Connect bootloader.bin will fit in its flash
partition.
Fix _flash_sizem calculation, division was not working properly because
FLASHSIZE included subtraction and defined value was not in parenthesis.
Prior to this change _flash_sizem was 0x00800000, now it is correctly set
to 4 in case of Sansa Connect and 8 in case of other TMS320DM320 players.
This significantly improves boot time as cache is now enabled only for
real flash memory region.
Change-Id: If3e50a3075c840dcb69dfafe5bba608a0acd2bf8
PMU interrupts are used to detect USB Vbus, wall adaptor, accessories
and holdswitch. A thread is needed to poll the PMU throught I2C, ATM
it does nothing but showing the state of the inputs on the HW debug
menu, funcionallity for each individual input will be added in next
patches.
Change-Id: If93bf2044d1052729237a7fd1431c8493e09f1c7
Do not rely on a bootloader initializing the HW, RB initializes
and configures GPIO, I2C, and PMU at startup.
Change-Id: If7f856b1f345f63de584aa4e4fc22d130cd66c80
Low level functions that do not depend on Rockbox kernel,
intended to be used by the bootloader, dualboot-installer,
RB drivers or other .dfu tools.
Change-Id: If80214d26e505265ace19d9704f1e1300f98b2f4
When the bootloader starts, most of HW never has been initialized.
This patch includes all code needed to perform the preliminary
initialization on SYSCON, GPIO, i2c, and MIU.
The code is based on emCORE and OF reverse engineering, ported to
C for readability.
Change-Id: I9ecf2c3e8b1b636241a211dbba8735137accd05c
This new header generator works differently from the previous one:
- it uses the new format
- the generated macro follow a different style (see below)
- the generated macro are highly documented!
- it supports SCT-style platform or RMW-style ones
Compared to the old style, the new one generate a big set of macros per
register/field/enum (loosely related to iohw.h from Embedded C spec). The user
then calls generic (names are customizable) macros to perform operations:
reg_read(REG_A)
reg_read(REG_B(3))
reg_read_field(REG_A, FIELD_X)
reg_read_field(REG_B(3), COOL_FIELD)
reg_write(REG_A, 0x42)
reg_write_field(REG_A, FIELD_X(1), FIELD_Y(3), IRQ_V(FIQ))
reg_write_fielc(REG_B(3), COOL_FIELD_V(I_AM_COOL), BLA(42))
the following use RMW or SET/CLR variants, depending on target:
reg_set_field(REG_A, FLAG_U, FLAG_V)
reg_clr_field(REG_A, FIELD_X, FIELD_Y, IRQ)
reg_clr_field(REG_B(3), COOL_FIELD, BLA)
the following does clear followed by set, on SET/CLR targets:
reg_cs(REG_A, 0xff, 0x42)
reg_cs(REG_B(3), 0xaa, 0x55)
reg_cs_field(REG_A, FIELD_X(1), FIELD_Y(3), IRQ_V(FIQ))
reg_cs_field(REG_B(3), COOL_FIELD_V(I_AM_COOL))
The generator code is pretty long but has lots of documentation and lots of
macro names can be customized.
Change-Id: I5d6c5ec2406e58b5da11a5240c3a409a5bb5239a
The write buffer size is undefined to use the default 24Kb. size
defined (and recomended) in usb_storage.c, the read buffer size is
also decremented to 24 Kb. USB sequential read and write benchmarks
using diskdump are now 8-9% faster.
Change-Id: Ia7c9f77b57c8ca5b566b508efffbd713d1587acf
This patch optimizes UDMA timings to increase write transfer rate on
ATA bus, these transfers are clocked by HCLK, tDVS+tDVH is modified to
decrease Tcyctyp (typical write cycle period). This is not overclocking,
we meet the ATA standar, the settings used by OF are not well optimized
for each UDMA mode, we will never know but probably this was due some
documentation issue.
ATA_UDMA_TIME register is documented on s3c6400 datasheet, information
included in s5l8700 datasheet is wrong or not valid for s5l8702.
From ATA specs, (Minimum, Maximum) values in nanoseconds:
UDMA 0 UDMA 1 UDMA 2 UDMA 3 UDMA 4
tACKENV (20, 70) (20, 70) (20, 70) (20, 55) (20, 55)
tRP (160, --) (125, --) (100, --) (100, --) (100, --)
tSS (50, --) (50, --) (50, --) (50, --) (50, --)
tDVS (70, --) (48, --) (31, --) (20, --) (6.7, --)
tDVH (6.2, --) (6.2, --) (6.2, --) (6.2, --) (6.2, --)
tDVS+tDVH (120, --) (80, --) (60, --) (45, --) (30, --)
Tcyc = tDVS+tDVH
WR[bytes/s] = 1/Tcyc[s] * 2[bytes]
On Classic (boosted):
HClk = 108 MHz. -> T = ~9.26 ns.
Old values (used by OF):
UDMA ATA_UDMA_TIME tACK tRP tSS tDVS tDVH Tcyc WR(MB/s)
0 0x5071152 27.8 166.7 55.6 74.1 55.6 129.7 15.4
1 0x3050a52 27.8 101.8 55.6 55.6 37 92.6 21.6
2 0x3030a52 27.8 101.8 55.6 37 37 74 27
3 0x2020a52 27.8 101.8 55.6 27.8 27.8 55.6 36
4 0x2010a52 27.8 101.8 55.6 18.5 27.8 46.3 43.2
New values:
UDMA ATA_UDMA_TIME tACK tRP tSS tDVS tDVH Tcyc WR(MB/s)
0 0x4071152 27.8 166.7 55.6 74.1 46.3 120.4 16.6
1 0x2050d52 27.8 129.6 55.6 55.6 27.8 83.4 24
2 0x2030a52 27.8 101.8 55.6 37 27.8 64.8 30.9
3 0x1020a52 27.8 101.8 55.6 27.8 18.5 46.3 43.2
4 0x1010a52 27.8 101.8 55.6 18.5 18.5 37 54
To verify that the settings are correct, a write-to-cache test was
performed using emCORE, the measured transfer rate (WRm) is compared
against the theoric transfer rate (WR) at 108 Mhz for the old and
the new UDMA4 settings (iPod 160, HDD Toshiba MK1634GAL):
UDMA ATA_UDMA_TIME Tcyc(ns) WR(MB/s) WRm(MB/s) RDm(MB/s)
4 0x2010a52 46.3 43.2 42.9 59.8
4 0x1010a52 37 54 53.5 59.8
Notes:
- The new UDMA4 settings increases ~25% the ATA transfer rate for
cached-writes. The real HDD write speed is limited by the internal
transfer rate (depends on cilinder, for the MK1634GAL it is 276 to
573 Mbits/s). Sequential write benchmark using diskdump on USB are
~8% faster.
- Read transfers are clocked by the device, it depends on UDMA mode
selected and are not affected by HClk or ATA_UDMA_TIME settings.
Read-from-cache tests results (RDm) using HClk=108 and HClk=54 for
UDMA4 are 59.8 MB/s on MK1634GAL.
- Minimum HClk is limited by tACKENV specs, using current settings
it is 54 MHz for UDMA4,UDMA3 and 43 MHz for UDMA2,UDMA1,UDMA0.
Change-Id: I61d67060410752518a59e1ff08072b21747ca997
When the bootloader starts only IRAM is available, the first task is to
ask the PMU to verify if the iPod has previously been hibernated by OF.
Due to memory limitations, the kernel cannot be used on this stage.
This patch modifies I2C and PMU low level functions to not to depend
on kernel (removes mutexes, and uses HW timer instead of current_tick),
actual kernel functions are modified to be 'mutexed' wrappers of the new
functions.
Change-Id: I7cef9e95dedaf176dc0659315f3dc33166d5b116
The kernel on this device reports nonexistent key presses, in particular it
reports right presses when pressing the left button... Since when it happens,
the right press comes after the left one, the new code simply ignores any
right press when the left button in pressed.
Change-Id: Ib6ced02682d9cecf4c7f6c58834907a667419cd7
Right now GUI boost interfers with test_codec running unboosted
by varying the CPU frequency. This at least makes it more consistent
if run without user input.
Change-Id: I121615098d6bd72ccd13c4e665cc2e4d45d7b58c
Add UART support for s5l8700/1 using the UC870X UART controller,
actually the functionallity is disabled and must be enabled for
each individual target. Tested on iPod Nano 2G (s5l8701), not
tested on s5l8700.
Change-Id: Ic0f216bb871502d355a70e4b658e536a2c0976a9
- Small rework on the UC8702 UART controller to make it compatible with
other s5l870x SOCs. Files moved and renamed, many conditional code
added to deal with capabilities and 'features' of the different CPUs.
- A couple of optimizacions that should not affect the functionality.
Change-Id: I705169f7e8b18d5d1da642f81ffc31c4089780a6
With this changes rockbox can be loaded from SD card when internal storage
can't be mount (due to hardware or software problem).
Change-Id: I32b20d3f341566364def747a708a54ba6b4a7f8b
The text is usually only a short description taken from the wiki and
don't contain screenshots or keymaps, but should be better than nothing. :)
Added manual entries:
- Boomshine
- Dict
- FFT
- main_menu_config
- Matrix
- Maze (including keymap)
- PDbox
- Superdom
Additional changes/fixes:
- fix "Clix" alphabetical order
- add Frotz & ZXBox to games preamble
Change-Id: I169870420cbac8123695747ccfcbaaf3478c11cc
Although the jz4740 contains a similar tool to usbboot, its command-line
interface is not very useful, also it does not compile by default because it
relies on some external code, and it contains code specific to some JZ4740
devices.
Change-Id: I22688238d147e21fb0fd524466b333b6003d4ff1
This commit adds support for the version of the hwstub library, which requires
a lot of changes. It also adds some editing features, such as register access
and much better editing of fields using the mouse (double click on a field
to be able to resize and move it).
Change-Id: I3c4e4cc855cb44911c72bc8127bad841b68efe52
Registers (and variants) can now specify the type of access supported:
- unspecified: for variant means same as register, for register defaults R/W
- read/write
- read only
- write only
Backward compatibility is preserved by setting access to unspecified by default.
Change-Id: I3e84ae18f962a45db62f996a542d08405d05b895
Also use this opportunity to cleanup support for multiple devices: the shell
now supports dynamic changes in the device and will call init() everytime
a new device is selected, to prepare a new environment. The shell now
honors register width on register read/write. The shell also provides access
to variants as follows by creating a subtable under the register using the
variant type in UPPER case and having the same layout as a register.
For example if register HW.GPIO.DIR has variants "set" and "clr", those can
be used like this:
HW.GPIO.DIR.SET.write(0xff)
HW.GPIO.DIR.CLR.write(0xff00)
Change-Id: I943947fa98bce875de0cba4338e8b7196a4c1165
Rewrite the hwstub library in C++, with a clean and modular design.
The library was designed from the ground up to be aware of multithreading
issues and to handle memory allocation nicely with shared pointers.
Compared to the original library, it brings the following major features:
- support for JZ boot devices, it is very easy to add support for others
- support for network transparent operations (through sockets): both tcp
and unix domains are support
Change-Id: I75899cb9c7aa938c17ede2bb3f468e7a55d625b4
After being caught by several bugs of the type "let's forgot to initialize
a field to default value", I'm finally fixing this.
Change-Id: I01c33e0611d4f697f767db66465e4fb30858cdab
