Many imx233 targets boot in a very low performance mode, typically cpu and
dram at 24MHz. This results in very slow boots and very unstable USB
bootloader mode. Since cpu frequency scaling is disabled in bootloader in
rockbox, always make the frequency scaling code available and boost at boot
time.
Change-Id: Ie96623c00f7c4cd9a377b84dcb14b772558cfa4d
The current code was spreaded over power and powermgmt which made
it behave strangely, especially since there are relationships
between power management and frequency scaling. The new code makes
sure power management is initialised before frequency scaling
starts. It also makes sure to start from a known state, thus
fixing potential issue when the bootloader stops in a trickle
state where DCDC is improperly configured.
Change-Id: Ibded2e590e108f6c98daa52d2cf1bd28763c8923
On the ZEN X-Fi2, the fractiona dividers are gated by the
bootloader and must be ungated before switching emi to pll.
Change-Id: I5df57ed5581054883da4cbb3b4f3ce3539391ab5
The clkctrl functions were becoming a mess. Normalise the names,
get rid of the xtal derived as special case and use the same
interface.
Change-Id: Ib954a8d30a6bd691914b5e0d97774ec9fc560c50
Move to a table based approach (scales better) and distinguish
between upward changes (increase frequency) and downward changes
(decrease frequency). This provides a better ordering of
operations and in particular it allows to avoid changing the
regulator while running at low speed since it takes a long time !
This should result in a much smoother scaling.
Change-Id: Iad7e5b61277e215f31c07877fbbad07ddde1171f
The manual recommands to tweak the arm cache settings on frequency
changes. The meaning of these values is undocumented but 0 seems
to be a safe value for all frequencies whereas 3 seems to be valid
only for low frequencies (<=64MHz ?)
Change-Id: Iaa8db4af8191010789cf986b1139ff259d73e2ed
CPU frequency scaling is basically useless without scaling the
memory frequency. On the i.MX233, the EMI (external memory
interface) and DRAM blocks are responsable for the DDR settings.
This commits implements emi frequency scaling. Only some settings
are implemented and the timings values only apply to mDDR
(extracted from Sigmatel linux port) and have been checked to
work on the Fuze+ and Zen X-Fi2/3. This feature is still disabled
by default but I expected some battery life savings by boosting
higher to 454MHz and unboosting lower to 64MHz.
Note that changing the emi frequency is particularly tricky and
to avoid writing it entirely in assembly we rely on the compiler
to not use the stack except in the prolog and epilog (because
it's in dram which is disabled when doing the change) and to put
constant pools in iram which should always be true if the
compiler isn't completely dumb and since the code itself is put
in iram. If this proves to be insufficient, one can always switch
the stack to the irq stack since interrupts are disabled during
the change.
Change-Id: If6ef5357f7ff091130ca1063e48536c6028f23ba
Do low level power init in system_init(). This can be needed
since imx233 must be able to frequecy scale atfer system_init()
and kernel_init() and this is only possible if power system was
initialised.
Change-Id: I27c66ec0dccd60bda26a45be24683c0bfe72c6da
When changing the cpu frequency, it is important to make sure that
HBUS stays at a reasonable frequency otherwise the chip will
crash. Special care is needed about auto-slow and clk_p/clk_h
ratio on intermediate steps.
Change-Id: Ief9f68ddf286caabe75c879718dac5027ab1560f
Frequency scaling seems to be unstable and causes the device to
freeze. It is unclear why at the moment, perhaps we need to ramp
up the vddd voltage to avoid a false brownout ?
Change-Id: I7aaea9d7c213922a65250fe50775fb785d430226
This does not scale the EMI frequency and keep the processor
betweel 261MHz and 454MHz. It can still be improve. The auto-slow
divisor could still be change, 8 seems reasonable for now
Change-Id: I639bb3f6b7f8efedc7dc58d08127849156eeb1b6
Implement PLL enabling/disable and unconditionally power the PLL
on startup. This is needed at least on the Zen X-Fi2.
Change-Id: Ib9ddfdeaf973cedded4b3586dd16aa95a61e78ba
The icoll code now has an IRQ storm detection mechanism which
will prevent the device from hard freezing in case it happen.
Change-Id: I9861238dce61d29af1e48f9c534ec63a7f23465c
Rework code to be more useful:
- move battery channel init to lradc
- always init lradc from system (previously from adc)
- don't reserve channels for vddio, nmos or pmos
- implement external temperature sensing using current source
- use this for battery sensing on the Fuze+ (calibration needed)
Change-Id: I5f9a24b9243db7d1e6bdb16b84bc891e61d0c318
Only enable fmradio_i2c once with _init() called from system.
Move actual i2c init to system for consistency.
Move tuner power pin setup to power instead of fmradio.
Change-Id: Idb56bfba5803f71b5d049f174c48d2afb969a6ea
implement button_init_device for ondio
include button.h to get prototypes
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31621 a1c6a512-1295-4272-9138-f99709370657
- now identity map dram uncached and have a cached and buffered virtual alias
- rework dma to handle virtual to physical pointers conversion
- fix lcd frame pointer
- implement usb detection properly
- implement bootloader usb properly
- allow the bootloader to disable MMC windowing (useful for recovery)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30432 a1c6a512-1295-4272-9138-f99709370657
