Searching in volume 0 is necessary for multiboot targets with only
one drive, like the M3K/Q1/ErosQ. Without this the search code will
never look at the redirect file on these targets.
The search bound is configured with a setting MULTIBOOT_MIN_VOLUME,
which defaults to 0, but is defined to 1 for Sansa players so they
keep their old behavior.
Change-Id: I6dc5cf98db4258731de2c68c3ab1182b4a4a655b
This kind of reverts 7b596416bf ("Gigabeat S: Update RDS processing to
use asynchronous I2C rather than thread."). However, requiring RDS to
run in thread context will a) allow more upcoming features and b) remove
quite some complexity from the codebase (see the diffstat here) because
Gigabeat is the only user. iMX31 should be able to handle one more
thread, as it can even run Linux.
Change-Id: I46130034595ba66392c5417c275d036f4bd26943
- Don't include the 'battery capacity' setting unless the
target allows changing it.
- Clean up the preprocessor conditionals used to check for
variable battery capacity support.
- Don't use a variable for battery capacity unless it is
actually needed.
Change-Id: I3d8a338f107014f2c5098bc0a44ef0cfb4df9356
Based on a patch by Amaury Pouly which was based on a patch from Ryan
Hitchman.
I mainly moved the code for polling into the tuner driver so it can be
reused by other targets. I added the CONFIG parameter for the polling
frequency (in ticks) to save energy. Also, I did some minor cleanups.
Change-Id: I95a62e7e1e42c62dbf47ecb27a3b312a42be62aa
All existing USB drivers now define USB_LEGACY_CONTROL_API to
enable the emulation layer.
Control request handlers will be ported in follow-up commits.
Change-Id: I4be1ce7c372f2f6fee5978a4858c841b72e77405
It has only a couple GB of onboard flash storage with no storage
driver in Rockbox. It hasn't seen any meaningful development since
its initial commit, it's not on the build farm, and the bootloader
build is broken by other refactoring.
Change-Id: Idd9e3c46fac9b96f416ce444182f97a50770e747
What works:
- LCD: 16-bit RGB565
- all buttons, including scrollwheel
- SD Card
- Battery level and charging/not charging status
- USB
- audio
- sample rate switching
- HP / LO detect, with "safe" fixed LO volume -
LO volume will only be put to user-defined max volume
if headphones are not present.
- rtc
- Plugins build, tried a couple and they seem OK
- Bootloader, installable to nand via usbboot
What doesn't work:
- Dual Boot
- power on/off has intermittent, low volume audio click
(sometimes it's completely silent, sometimes there's
a click)
- Audio uses 16-bit volume scaling, so clicking/popping
is pretty bad at lower volumes - need 32 bit volume
scaling, 24 bit I2S data
- USB HID keys not yet defined
- no jztool support
Unknowns:
- Stereo Switch pins: Direction select, AC_DC
(probably not even hooked up)
- What is the actual purpose of the Stereo Swtich?
- How does the bluetooth module connect?
"Someday" stuff:
- get LCD working at higher bit depth
- Bluetooth
Change-Id: I70dda8fc092c6e3f4352f2245e4164193f803c33
- Audio playback works
- Touchscreen and buttons work
- Bootloader works and is capable of dual boot
- Plugins are working
- Cabbiev2 theme has been ported
- Stable for general usage
Thanks to Marc Aarts for porting Cabbiev2 and plugin bitmaps.
There's a few minor known issues:
- Bootloader must be installed manually using 'usbboot' as there is
no support in jztool yet.
- Keymaps may be lacking, need further testing and feedback.
- Some plugins may not be fully adapted to the screen size and could
benefit from further tweaking.
- LCD shows abnormal effects under some circumstances: for example,
after viewing a mostly black screen an afterimage appears briefly
when going back to a brightly-lit screen. Sudden power-off without
proper shutdown of the backlight causes a "dissolving" effect.
- CW2015 battery reporting driver is buggy, and disabled for now.
Battery reporting is currently voltage-based using the AXP192.
Change-Id: I635e83f02a880192c5a82cb0861ad3a61c137c3a
Use 32-bit monotime AVR counter for time tracking. Set the time by
adding fixed offset to the counter value. Store the offset in rockbox
directory to make it persistent between reboots.
Do not implement alarm functionality as wakeup is only possible from
sleep and not from complete power off.
Change-Id: I615c7eb4df8ab0619dcbfcff107bc7051a15aace
Acknowledge SYS_USB_CONNECTED in all queues so USB task can gain
exclusive access to the storage.
Reduce CPPI requeue timeout to speed up disk access.
Change-Id: I322aae4cac679696bb8186ccacf838a18f0715e9
Port USB driver from Sansa Connect Linux kernel sources. The device
successfully enumerates and responds to SCSI commands but actual disk
access does not work. The SCSI response sent to host mentions that both
internal storage and microsd card are not present.
Change-Id: Ic6c07da12382c15c0b069f23a75f7df9765b7525
It never worked, and hasn't compiled in something like a decade, Given
the HW capabilities (limited onboard flash, no expandability) there's
really no point in trying to fix/complete it.
Change-Id: I7d175089840396f8891645bd10010d730dd5bfdc
They were never finished, never saw any release ever, and haven't
compiled for the better part of a decade. Given their HW capabilities [1],
they are not worth trying to fix.
[1] 1-2MB RAM, ~256MB onboard flash, no expandability
Change-Id: I7b2a5806d687114c22156bb0458d4a10a9734190
The Q and K have a slightly different case, but the hardware under the
shell is completely identical.
These models are rebadged versions:
* Hifiwalker H2 (== Q)
* AGPTek H3 (== K)
* Surfans F20 (== K)
Other notes:
* Significant improvements in the shared Hiby-platform launcher/loader
* SD card can theoretically be hot-swapped now
* Support external USB mass storage!
* Some consolidation of Hiby-platform targets
* Some consolidation of plugin keymaps
Todo/known issues:
* Keymaps need to be gone over properly
* Convert to HAVE_SCROLLWHEEL?
Change-Id: I5a8a4f22c38a5b69392ca7c0a8ad8c4e07d9523c
Most credit goes to: Roman Skylarov
Additional integration and refactoring by myself.
*** COMPLETELY UNTESTED ***
Change-Id: Ia64c36d92e0214c6b15f7a868df286f8113ea27b
* SAMPR_CAPS_ALL -> SAMPR_CAPS_ALL_48/96/192
* All targets claiming SAMPR_CAPS_ALL now get appropriate subset
* No need to explicitly define HAVE_PLAY_FREQ
* Rates that are a multiple of 44 or 48KHz can be used for playback
Inspired by a patch by Roman Stolyarov, but substantially rewritten by myself.
Change-Id: Iaca7363521b1cb9921e047ba1004d3cbe9c9c23e
Note: I left behind lcd_bitmap in features.txt, because removing it
would require considerable work in the manual and the translations.
Change-Id: Ia8ca7761f610d9332a0d22a7d189775fb15ec88a
'swcodec' is now always set (and recording_swcodec for recording-capable
units) in feature.txt so the manual and language strings don't need to
all be fixed up.
Change-Id: Ib2c9d5d157af8d33653e2d4b4a12881b9aa6ddb0
Provided by Roman Stolyarov
Integration, Refactoring, and Upstreaming by Solomon Peachy
X3II confirmed working by forum tester, X20 is nearly identical.
This includes bootloader, main firmware, and the flash image patcher.
Eventual Todo:
* Further refactor AGPTek Rocker & xduoo hiby bootloaders
* Further refactor AGPTek Rocker & xduoo hosted platform code
Change-Id: I34a674051d368efcc75d1d18c725971fe46c3eee
Cleaned up, rebased, and forward-ported from the xvortex fork.
(original credit to vsoftster@gmail.com)
Change-Id: Ibcc023a0271ea81e901450a88317708c2683236d
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Allow user to select cpu undervolt
There have been quite a few issues across the SANSA AMS line related
to CPU undervolting while most players show greatly increased runtime
some crash.
Rather than constanly upping the voltage we now have a
setting with a safe value for all players and the option for lower voltages
I plan to add a few other options here later such as disk
timings and maybe some other clocks/experimental settings
Added: Disk Low speed option for AS3525v2 devices cuts
frequency to 12 MHz from 24 MHz
Added: Disk Low speed option for AS3525v1 devices cuts
frequency to 15.5 MHz from 31 MHz
Added: I2c Low Speed AS3525 devices, should be bigger improvement for v1 devices
Fixed: Debug menu for AS3525v2 No SDSLOT frequency,
Showed IDE freq though it is unused
Added: DBOP and SSP underclocking affects display on v1/v2 respectively
Fixed: debug menu now has SSP frequency, and SSP_CPSR
Update: made settings menu more generic
Update: cleaned up code
Added: Clip v1 & Fuze v1 didn't have HAVE_ADJUSTABLE_CPU_VOLTAGE.
not sure why but, waiting on testing to confirm
Added: C200v2 and E200v2 devices and HAVE_ADJUSTABLE_CPU_VOLTAGE.
Fixed: v1 devices don't like display timing set lower (dbop)
v1 devices don't have a divider set for ssp (causes divide by 0)
Fixed: ClipZip display lags with Max SSP divider changed from 0xFE to 0x32
Fixed: v1 devices didn't work properly with highspeed sd cards
Added code from http://gerrit.rockbox.org/r/#/c/1704/
Added powersave and IDE interface enable/disable
Added: V2 devices now have powersave enabled on sd interface
Update: cleaned up code, lang defines, added manual entries
Update ssp clock mechanism added calculated ssp divider to clipzip
Update turn display clock off when clip+ turns off display
Fixed: clipzip wrong register for SSP clock
Change-Id: I04137682243be92f0f8d8bf1cfa54fbb1965559b
TODO: add other players?
Instead of checking ticks, set a sticky dirty flag that indicates
that the RTC needs to be read. This gives a timely update and more
accurate readout without actually reading the RTC until it changes.
The implementation should atomically read the flag and clear it.
Setting the flag would typically happen in an RTC tick ISR.
Change-Id: I6fd325f22845029a485c502c884812d3676026ea
Adds the ability to load firmware from other drives on MULTIVOLUME targets
Mihail Zenkov <mihail.zenkov@gmail.com> had posted a hard coded patch
to allow this on several Sansa players, I made it more universal
Redirect file rockbox_main.<name> should placed in root of
drive you would like to be main, if this file empty or there a single
slash '/' firmware will be loaded from /.rockbox in root of this drive
If instead a /<*DIRECTORY*> is supplied in rockbox_main.<name> then
firmware will be loaded from /<dir>/.rockbox/
NOTES*
The directory can have multiple levels however..
leading slash MUST be included
trailing slash can be omitted
(eg. /test/.rockbox would be simply '/test' in the redirect file)
Redirect file will not work on internal drive (whatever is default boot drive)
Volume with the highest index containing redirect file will be loaded
first.
Firmware file is checked for boot data region, if missing, firmware
image will not be loaded.
On failure or if no redirect file is found load will fallback to
internal drive
Currently only Sansa Fuze+, Sansa Clip+,
Sansa Clip Zip, Sansa Fuzev2, and Sansa Fuzev1 are implemented.
Players (with HAVE_MULTIVOLUME)
will need #define HAVE_BOOTDATA and #define BOOT_REDIR "rockbox_main.<name>"
added to their config file
boot_data is implemented in crt0.s file (See g#1552)
ARM and IMX233 have aleady been implemented
Once these conditions are met <HAVE_MULTIBOOT> will be defined by config.h
Partitions on the drives are able to have a redirect as
well.
Change-Id: Iada3263919f6bcad7d0d7d8279b4239aafa07ee9
Strangely it has the SAME encryption key as the E450. Either they didn't bother
changing it or more likely they have exactly the same internals and a slightly
different case.
Change-Id: I39ab88845b3e40db34160c2e61dde421f391df44
SUPPORTED SERIES:
- NWZ-E450
- NWZ-E460
- NWZ-E470
- NWZ-E580
- NWZ-A10
NOTES:
- bootloader makefile convert an extra font to be installed alongside the bootloader
since sysfont is way too small
- the toolsicon bitmap comes from the Oxygen iconset
- touchscreen driver is untested
TODO:
- implement audio routing driver (pcm is handled by pcm-alsa)
- fix playback: it crashes on illegal instruction in DEBUG builds
- find out why the browser starts at / instead of /contents
- implement radio support
- implement return to OF for usb handling
- calibrate battery curve (NB: of can report a battery level on a 0-5 scale but
probabl don't want to use that ?)
- implement simulator build (we need a nice image of the player)
- figure out if we can detect jack removal
POTENTIAL TODOS:
- try to build a usb serial gadget and gdbserver
Change-Id: Ic77d71e0651355d47cc4e423a40fb64a60c69a80
* Remove unused bits like the radio event and simplify basic
radio interface. It can be more self-contained with rds.h only
required by radio and tuner code.
* Add post-processing to text a-la Silicon Labs AN243. The chip's
error correction can only do so much; additional checks are highly
recommended. Simply testing for two identical messages in a row
is extremely effective and I've never seen corrupted text since
doing that, even with mediocre reception.
Groups segments must arrive in order, not randomly; logic change
only accepts them in order, starting at 0.
Time readout was made a bit better but really we'd need to use
verbose mode and ensure that no errors were seen during receiving
of time and more checks would be need to have a stable PI. The
text is the important bit anyway.
* Time out of stale text.
* Text is no longer updated until a complete group has been
received, as is specified in the standard. Perhaps go back to
scrolling text lines in the radio screen?
* Add proper character conversion to UTF-8. Only the default G0
table for the moment. The other two could be added in.
* Add variants "RDS_CFG_PROCESS" and "RDS_CFG_PUSH" to allow
the option for processed RDS data to be pushed to the driver and
still do proper post-processing (only text conversion for now for
the latter).
Change-Id: I4d83f8b2e89a209a5096d15ec266477318c66925
The function is neither reentrant nor ISR callable. Instead of
using a ticked-based timeout, have the button driver provide the
unboost after a delay when waiting for a button.
HAVE_GUI_BOOST gets immediate boost after dequeuing any message,
otherwise the queue has to have at least three messages waiting
for it to trigger a boost-- essentially the behavior that existed
but now combined in one place.
Change-Id: I1d924702840f56a1a65abe41fa92b4e753c4e75a
Playlist dircache references should be back in working order.
Reenabling dircache references in the database ramcache is not
yet done as it requires quite a bit of rework. Otherwise, the
database in RAM is functional again.
Some buffer compatibility changes have been made for database
commit because the dircache buffer can no longer be stolen, only
freed by an API call.
Change-Id: Ib57c3e98cb23e798d4439e9da7ebd73826e733a4
Based on g#844 and g#949, it is intended as a replacement for the
current s3c6400x USB driver.
The DesignWare USB OTG core is integrated into many SoC's, however
HW core version and capabilities (mainly DMA mode, Tx FIFO mode,
FIFO size and number of available IN/OUT endpoins) may differ:
CPU targets HW ver DMA NPTX FIFO FIFO sz #IN/OUT
-------- ------------- ------ --- --------- ------- -------
as3525v2 sansaclipplus 2.60a Yes Dedicated 0x535 4/4
sansaclipv2
sansaclipzip
sansafuzev2
s5l8701 ipodnano2g 2.20a Yes Shared 0x500 4/5
s5l8702 ipod6g 2.60a Yes Dedicated 0x820 7/7
ipodnano3g
s5l8720 ipodnano4g ? ? ? ? ?
Functionality supported by this driver:
- Device mode, compatible with USB 1.1/2.0 hosts.
- Shared FIFO (USB_DW_SHARED_FIFO) or dedicated FIFOs.
- No DMA (USB_DW_ARCH_SLAVE) or internal DMA mode.
- Concurrent transfers: control, bulk (usb_storage, usb_serial) and
interrupt (usb_hid).
Actually this driver is not used by any CPU, it will be enabled for
each individual CPU/target in next patches.
Change-Id: I74a1e836d18927a31f6977d71115fb442477dd5f
