Hold "Play" to boot the OF, or boot it from the recovery menu
by holding "Vol. Up". If you had the hosted port installed on your
player before installing the native port, you'll still have to go
through the hosted bootloader.
A couple notes:
- When booting from the menu, the recovery menu disappears, then
reappears before going into the OF.
- You need to hold the play button for like a half second after the
blue light comes on in order to get into the OF.
The recovery appears to be there, but it doesn't seem to be intended
for end users - it just says "Updater V1.1 - Insert TF Pls". I haven't
tested it beyond seeing that it boots, so I'm going to comment it out
for now.
Change-Id: Ie271ee479bb628cc74141b7fe07273b3f193f358
Remove the battery power ADC since it's not used right now,
and seems to fluctuate too rapidly to be of much use.
Change-Id: If115e4e3ce14d4c18ce899f5a889f7f99ab66489
This caused LCD problems on the ErosQ, where the screen would
go white until being put through a sleep/wake cycle. The exact
reason for this isn't obvious, but the problem didn't exist
prior to the AXP driver rewrite.
The two dependent changes,
42999913ba - x1000: Increase USB current limit to 500 mA at all times
90dd2f84a9 - x1000: Correctly limit USB charging current
ended up bringing the USB charging situation back to where it
was prior to the rewrite, so the cleanest option is to revert
the whole lot.
This reverts commit 42999913ba.
This reverts commit 90dd2f84a9.
This reverts commit 2d89143962.
Change-Id: I1cff2bfdd1b189df14bcf8cce42db725caa470d7
The 100 mA USB current limit added in commit 90dd2f84a9
is a problem when booting with a completely dead battery.
Often 100 mA isn't enough to power the player, never mind
charge the battery, so revert to the old behavior of only
limiting charge current.
Given that the original firmware on these devices isn't
following the USB spec to the letter, it's probably not
worth trying to make Rockbox do so unless and until it
causes a real problem - which hasn't happened yet.
Change-Id: I179a08310c226fe01460680c62fd25fd69079256
The way this was done before was wrong - limiting the charge
current is not enough since the device will draw additional
power to run. Use the AXP192's vbus current limit control to
stay compliant with the USB specification.
Change-Id: I91b84e3480a432e49bec53cf2a17e4e3444404a4
I noticed a few mistakes in the old driver code and it was in
need of an overhaul anyway... I decided to scale things back,
simplify the code and remove most of the debug menus, netting
a nice code size savings.
One new feature is an advanced debug menu which is accessible
by recompiling the code with AXP_EXTRA_DEBUG. It adds quite a
bit of code size and isn't useful other than for development
so it must be manually enabled by editing the source.
Change-Id: I30e17c1194c14823decd726a574ed14451d4cb2d
This allows battery run time to be calculated from the
actual battery usage on the FiiO M3K and Shanling Q1.
This isn't very good for the time being and the estimate
tends to go all over the place due to small variations
in current or voltage.
The Eros Q can support this feature as well, but since
it already has fixed estimates defined and the quality
of the "real time" estimate is low I am not enabling it
there.
Change-Id: Id34a93ee4b7d66f9f7e56ef0f5149f67e8e72039
All three X1000 native targets turned out to have a very
similar boot configuration and used a nearly identical
makefile. Eliminate this duplication by moving the logic
into the main makefile.
Change-Id: I13044b9675c0abd605b8accdb2fee4f54549b020
Appears to return 0 until the axp has (presumably) completed
its first real measurement.
Note about erosq: keep the power_inint() delay large to ensure
nothing breaks in the bootloader for the time being.
Change-Id: I444e858207cc401c42f1e6ceacf067ad543d4ff8
The battery stabilization delay call seems to need to be
about 170 at minimum now, let's do 190 for safety (+20ms).
Change-Id: Ifd0248891abe827dfcc3e6baf48cc5bef0d0cc1c
Write -1 to AIC_DR to initialize the "last sample"
to -1 in order to prevent power-on clicks.
It appears necessary to completely fill the FIFO,
otherwise I was able to get a click out of it, however
uncommon it was.
Not only does this prevent a click when first
playing a song after power-on, but it also seems to prevent
any click at all when powering on - previously, a small
click may have been heard when first booting.
Change-Id: I2b81c2fa6af9809ef1c354d7a08ca8f9893a7690
Previously it used the last sample, which turns out to be broken.
The AIC appears to send out a random non-zero sample continously
after boot -- probably because the last sample is uninitialized by
the hardware. Disabling playback is supposed to make it send zero
samples irregardless of the LSMP bit according to the docs, but it
doesn't seem to work this way.
- Change eliminates the white noise heard on the M3K after boot.
- Change has no adverse effects on the Q1.
- Leave Eros Q on the old setting since sending zeros exacerbates
clicking due to DAC's automute feature.
Change-Id: I9996793fc34f4475b19700d076b11505353b3836
Adjust the battery scale to be a little better. I've set
the 100% (discharge) point to be where the battery sags to
when it is done charging but still plugged in.
Not quite sure how best to set the charge scale, it's just
equal to the discharge scale for now.
Change-Id: I9a2730c0b2051300af9eeddb4f67164f38a29002
What works:
- LCD: 16-bit RGB565
- all buttons, including scrollwheel
- SD Card
- Battery level and charging/not charging status
- USB
- audio
- sample rate switching
- HP / LO detect, with "safe" fixed LO volume -
LO volume will only be put to user-defined max volume
if headphones are not present.
- rtc
- Plugins build, tried a couple and they seem OK
- Bootloader, installable to nand via usbboot
What doesn't work:
- Dual Boot
- power on/off has intermittent, low volume audio click
(sometimes it's completely silent, sometimes there's
a click)
- Audio uses 16-bit volume scaling, so clicking/popping
is pretty bad at lower volumes - need 32 bit volume
scaling, 24 bit I2S data
- USB HID keys not yet defined
- no jztool support
Unknowns:
- Stereo Switch pins: Direction select, AC_DC
(probably not even hooked up)
- What is the actual purpose of the Stereo Swtich?
- How does the bluetooth module connect?
"Someday" stuff:
- get LCD working at higher bit depth
- Bluetooth
Change-Id: I70dda8fc092c6e3f4352f2245e4164193f803c33
