Enables multiboot for the FiiO M3K, Shanling Q1, and Eros Q native port.
Note this requires an up-to-date Rockbox _and_ bootloader.
Usage instructions will (eventually) be found on the wiki:
https://www.rockbox.org/wiki/MultibootBootloader
Change-Id: Ia2da1ad6ef611e499d2fbafa93838387bc1023ba
Screenshots of the recovery menu will be useful for documentation.
This can be disabled by turning off HAVE_BOOTLOADER_SCREENDUMP in
the target config file if the bootloader should ever run up against
max size limits.
Change-Id: I62ec1e465df2ca7a8a0e78625d88b31f6c4ef078
This problem actually had nothing to do with USB boot; it's
because the cable is plugged in when the USB mode menu item
is selected. The USB thread detected the select button press
and went into charge-only mode (as it usually does when you
hold down a key in Rockbox). This is fixed by having the USB
thread ignore most keys in the bootloader.
USB connect events are delivered via the button queue, and
there were also cases where the connection could be missed
if the event happened within another UI screen. This should
also be fixed.
Change-Id: I077d705a6ac845c8713219eee45d26aa6addfa61
This allows battery run time to be calculated from the
actual battery usage on the FiiO M3K and Shanling Q1.
This isn't very good for the time being and the estimate
tends to go all over the place due to small variations
in current or voltage.
The Eros Q can support this feature as well, but since
it already has fixed estimates defined and the quality
of the "real time" estimate is low I am not enabling it
there.
Change-Id: Id34a93ee4b7d66f9f7e56ef0f5149f67e8e72039
This boosts USB transfer performance a bit, ~10% for reads and
~25% for writes, for large-ish file transfers. Rockbox is still
around 33-50% slower than the OF.
Change-Id: I236a1e5c69a290c47ed27b70cb2631111fc157ed
Upon getting a USB reset, the USB core will update charging
current by calling usb_charging_maxcurrent_change(). On all
current X1000 targets this may cause a hang, since changing
the charge current involves a blocking I2C transaction.
Eg. if the host issues a reset when we're already configured
as part of error recovery, the change from 500 mA -> 100 mA
will cause a hang.
Change-Id: I5b45272c01fa16b179ae3d16bbc50c7fab9a416b
A reasonable default assumption for a user
would be that they can plug their device into
a USB AC adapter and it will charge with as much
current as it reasonably can. With the previous
default, an AC adapter will only do 100mA, basically
a trickle charge.
Make this configurable default per-device, so as not
to break old devices without testing.
Define TARGET_USB_CHARGING_DEFAULT to USB_CHARGING_FORCE
to use the new default.
Tested on both erosQ Native and M3K.
Change-Id: I77265d356a41d67357ebc6e9f7e0c25a37b74931
What works:
- LCD: 16-bit RGB565
- all buttons, including scrollwheel
- SD Card
- Battery level and charging/not charging status
- USB
- audio
- sample rate switching
- HP / LO detect, with "safe" fixed LO volume -
LO volume will only be put to user-defined max volume
if headphones are not present.
- rtc
- Plugins build, tried a couple and they seem OK
- Bootloader, installable to nand via usbboot
What doesn't work:
- Dual Boot
- power on/off has intermittent, low volume audio click
(sometimes it's completely silent, sometimes there's
a click)
- Audio uses 16-bit volume scaling, so clicking/popping
is pretty bad at lower volumes - need 32 bit volume
scaling, 24 bit I2S data
- USB HID keys not yet defined
- no jztool support
Unknowns:
- Stereo Switch pins: Direction select, AC_DC
(probably not even hooked up)
- What is the actual purpose of the Stereo Swtich?
- How does the bluetooth module connect?
"Someday" stuff:
- get LCD working at higher bit depth
- Bluetooth
Change-Id: I70dda8fc092c6e3f4352f2245e4164193f803c33
