This patch changes all references/assumptions of PCLK to IDE_CLK for the internal pl180 controller.
Lower the AS3525_IDE_FREQ to 50 MHz in order to be able to divide by 2 for 25 MHz on the internal SD card.
Adjust the code in debug-as3525.c to account for the change and the frequencies reported should be correct.
Add some #if defined(HAVE_MULTIDRIVE) conditionals to cut out the code dealing with uSD for the clip.
Isolate the write delay needed for low frequency writes to only run for standard speed uSD cards. That is the only case for an MCICLK at 15.5 MHz.
Internal cards run at 25 MHz, HS uSD at 31 MHz, and standard speed uSD cards at 15.5 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23929 a1c6a512-1295-4272-9138-f99709370657
Some cards need this delay now that we're running at ident speed during this part of the init stage.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23919 a1c6a512-1295-4272-9138-f99709370657
Addition of a small write delay avoids data crc failures at lower MCICLK frequencies.
Check the actual speed value from the card's CSD register to determine HS status. HS cards can run at twice the speed of standard speed SD cards.
Internal cards & standard speed uSD now run at PCLK/4 = 15.5 MHz. HS uSD cards run at PCLK/2 = 31 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23901 a1c6a512-1295-4272-9138-f99709370657
It seems that lowering the operating frequency for the SD cards has made some uSD cards have problems with the init process.
By moving the boost from ident to operating frequency to after the switch to HS timing these card now seem to init normally.
We still need to fix the problem where the internal cards and non HS uSD cards are still slightly overclocked at 31 MHz.
As of now we experience data crc failures during writes at the next lower frequency of 15.5 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23870 a1c6a512-1295-4272-9138-f99709370657
This is within the SD Spec for v2 High Speed cards but still over the 25 MHz limit for v1 and non-HS v2 cards.
Test_disk write & verify passes on both internal and uSD.
The v1 cards still need to be lowered to 15 MHz but that causes data crc failures at this point.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23835 a1c6a512-1295-4272-9138-f99709370657
Currently the bypass bit is not cleared so it's possible to enter the identification phase at bypass speed instead of ident speed.
The simplest solution to ensure the bypass bit is not set is to set the register with an = operation instead of |=.
This makes setting the MCI_CLOCK register at the end of the controller init unnecessary.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23830 a1c6a512-1295-4272-9138-f99709370657
If the controllers were already enabled there was a chance we could try to read the MCI_CLOCK registers while the cards were buffering and then disable the controllers prematurely.
I guess funman knows and sees all!! Thanks funman.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23811 a1c6a512-1295-4272-9138-f99709370657
Because we turn off the clocks to the SD controllers between disk accesses we were unable to read the MCI_CLOCK registers until there was a disk access. Now we can read them immediately.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23810 a1c6a512-1295-4272-9138-f99709370657
Enabling/disabling of the NAF and IDE clocks is now grouped together as both are related to the internal SD.
Sequence for disabling SD now mirrors the enable sequence.
Comments added to make it easier to follow the configuration change for XPD from gpio to mci-sd and back.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23808 a1c6a512-1295-4272-9138-f99709370657
We had 3 different references to the same value. Rockbox always uses a blocksize of 512 bytes for SD and we were using SECTOR_SIZE, SD_BLOCK_SIZE, & card_info[drive].blocksize to use this value. Now the only reference being used is SD_BLOCK_SIZE.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23746 a1c6a512-1295-4272-9138-f99709370657
Flyspray: FS#10371
Authors: Fred Bauer and myself
Only enabled on e200v2 and Fuze (crashes on clipv1)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23739 a1c6a512-1295-4272-9138-f99709370657
When read it returns all enabled interrupt sources
When written it enables interrupt sources for each bit set
So just like VIC_INT_EN_CLEAR, we don't have to read the previous value
before writing to it (VIC_INT_EN_CLEAR is write-only anyway)
Thanks to Fred Bauer for spotting
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23734 a1c6a512-1295-4272-9138-f99709370657
We don't need to check the FIFO for MCI_RX_ACTIVE because we don't experience problems reading from the SD cards.
We need the MCI_TX_ACTIVE FIFO check during writes because some SD cards spend longer times in the PRG state
programming the data that has been written to them.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23733 a1c6a512-1295-4272-9138-f99709370657
We use wait_for_state() before any command that requires a state prior to being sent. Waiting after a transfer is not needed.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23732 a1c6a512-1295-4272-9138-f99709370657
of the CH_CONTROL and CH_CONFIGURATION registers easier to follow.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23725 a1c6a512-1295-4272-9138-f99709370657
The crc check on responses to sd commands was being bypassed due to a SD_APP_OP_COND special case. Now a short response is returned
even if the crc check fails so we can check the busy bit. The send_cmd() function still returns a false value but it loads the response
variable with the cmd response.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23718 a1c6a512-1295-4272-9138-f99709370657
- two essential parts of Sansa AMS drivers are optimzed away in newer gcc, so mark them volatile.
- use "r" instead of "i" (which is apparently invalid syntax) for the input list in some inline assembly
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23634 a1c6a512-1295-4272-9138-f99709370657
