Depends on http://gerrit.rockbox.org/r/#/c/1043/.
This patch adds a new setting in Settings -> General -> System: USB Mode.
Usable in Quickscreen and Shortcuts.
Possible settings are:
- Mass Storage: The default, on USB connect export the internal and external
drives as usual. Rockbox will exit gracefully in this case, since the internal
drive (/mnt/sdcard) is exported as mass storage device and Android prevents
Rockbox from continued execution.
- Charge Only: USB charge only, do not export the internal and external drives.
This will not close Rockbox.
- ADB: Enable the Android Debug Bridge. This will not close Rockbox.
Charge only and ADB are actually the same, since it is not yet established if
charge only is doable without adb and major hooks into Android.
German translation provided.
This may be genric for Android based devices but is only enabled
for iBasso Devices. Other maintainers may choose do adopt this.
Change-Id: I616247c29946c6595ebcf8f0c14b2410c9f0498b
Depends on http://gerrit.rockbox.org/r/#/c/1043/.
This patch adds a new setting in Settings -> General
-> System: Freq Scaling Governor
Usable in Quickscreen and Shortcuts.
Possible settings are:
- Conservative: Slow frequency switching.
- Ondemand or Interactive: Fast frequency switching.
- Powersave: Allways lowest frequency.
- Performance: Allways highest frequency.
German translation provided.
This may be genric for Android kernel based devices but is only enabled
for iBasso Devices. Other maintainers may choose do adopt this.
Change-Id: I10296f5be9586ad3a409105db0cd03682a30e9c1
perceptual bass enhancement
- a bbe-ish group delay corrction with Biophonic EQ boost.
- precut
auditory fatigue reduction
-reduce signal in frequency that may trigger temporary threshold shift
haas surround
-frequency between f(x1) and f(x2) is always bypassed.
-can apply to side only.
Change-Id: Icb6355ce9b1c99bf2c58c9385c3c411c0ae209d3
To stop erroneous button presses, allow users to add a deadzone between
the button via the Settings > General > System menu > Touch Dead Zone.
The configuration was chosen this way: the touchpad has the same DPI
in both direction so the setting applies the same on both the X and Y
axis. The setting ranges from 0 to 100 and is internally multiplied by 2
giving a maximum deadzone of 2*100 = 200 around each button, which
account for 400 total (once around each button), effectively reducing
each virtual button from 1000x600 to 600x200 when using the maximum value.
Change-Id: I8683c63d2950200eb32d1dda0a00bbd92d83d5be
Reviewed-on: http://gerrit.rockbox.org/677
Reviewed-by: Benjamin Brown <foolshperson@gmail.com>
Tested: Benjamin Brown <foolshperson@gmail.com>
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
This patch redoes the filesystem code from the FAT driver up to the
clipboard code in onplay.c.
Not every aspect of this is finished therefore it is still "WIP". I
don't wish to do too much at once (haha!). What is left to do is get
dircache back in the sim and find an implementation for the dircache
indicies in the tagcache and playlist code or do something else that
has the same benefit. Leaving these out for now does not make anything
unusable. All the basics are done.
Phone app code should probably get vetted (and app path handling
just plain rewritten as environment expansions); the SDL app and
Android run well.
Main things addressed:
1) Thread safety: There is none right now in the trunk code. Most of
what currently works is luck when multiple threads are involved or
multiple descriptors to the same file are open.
2) POSIX compliance: Many of the functions behave nothing like their
counterparts on a host system. This leads to inconsistent code or very
different behavior from native to hosted. One huge offender was
rename(). Going point by point would fill a book.
3) Actual running RAM usage: Many targets will use less RAM and less
stack space (some more RAM because I upped the number of cache buffers
for large memory). There's very little memory lying fallow in rarely-used
areas (see 'Key core changes' below). Also, all targets may open the same
number of directory streams whereas before those with less than 8MB RAM
were limited to 8, not 12 implying those targets will save slightly
less.
4) Performance: The test_disk plugin shows markedly improved performance,
particularly in the area of (uncached) directory scanning, due partly to
more optimal directory reading and to a better sector cache algorithm.
Uncached times tend to be better while there is a bit of a slowdown in
dircache due to it being a bit heavier of an implementation. It's not
noticeable by a human as far as I can say.
Key core changes:
1) Files and directories share core code and data structures.
2) The filesystem code knows which descriptors refer to same file.
This ensures that changes from one stream are appropriately reflected
in every open descriptor for that file (fileobj_mgr.c).
3) File and directory cache buffers are borrowed from the main sector
cache. This means that when they are not in use by a file, they are not
wasted, but used for the cache. Most of the time, only a few of them
are needed. It also means that adding more file and directory handles
is less expensive. All one must do in ensure a large enough cache to
borrow from.
4) Relative path components are supported and the namespace is unified.
It does not support full relative paths to an implied current directory;
what is does support is use of "." and "..". Adding the former would
not be very difficult. The namespace is unified in the sense that
volumes may be specified several times along with relative parts, e.g.:
"/<0>/foo/../../<1>/bar" :<=> "/<1>/bar".
5) Stack usage is down due to sharing of data, static allocation and
less duplication of strings on the stack. This requires more
serialization than I would like but since the number of threads is
limited to a low number, the tradoff in favor of the stack seems
reasonable.
6) Separates and heirarchicalizes (sic) the SIM and APP filesystem
code. SIM path and volume handling is just like the target. Some
aspects of the APP file code get more straightforward (e.g. no path
hashing is needed).
Dircache:
Deserves its own section. Dircache is new but pays homage to the old.
The old one was not compatible and so it, since it got redone, does
all the stuff it always should have done such as:
1) It may be update and used at any time during the build process.
No longer has one to wait for it to finish building to do basic file
management (create, remove, rename, etc.).
2) It does not need to be either fully scanned or completely disabled;
it can be incomplete (i.e. overfilled, missing paths), still be
of benefit and be correct.
3) Handles mounting and dismounting of individual volumes which means
a full rebuild is not needed just because you pop a new SD card in the
slot. Now, because it reuses its freed entry data, may rebuild only
that volume.
4) Much more fundamental to the file code. When it is built, it is
the keeper of the master file list whether enabled or not ("disabled"
is just a state of the cache). Its must always to ready to be started
and bind all streams opened prior to being enabled.
5) Maintains any short filenames in OEM format which means that it does
not need to be rebuilt when changing the default codepage.
Miscellaneous Compatibility:
1) Update any other code that would otherwise not work such as the
hotswap mounting code in various card drivers.
2) File management: Clipboard needed updating because of the behavioral
changes. Still needs a little more work on some finer points.
3) Remove now-obsolete functionality such as the mutex's "no preempt"
flag (which was only for the prior FAT driver).
4) struct dirinfo uses time_t rather than raw FAT directory entry
time fields. I plan to follow up on genericizing everything there
(i.e. no FAT attributes).
5) unicode.c needed some redoing so that the file code does not try
try to load codepages during a scan, which is actually a problem with
the current code. The default codepage, if any is required, is now
kept in RAM separarately (bufalloced) from codepages specified to
iso_decode() (which must not be bufalloced because the conversion
may be done by playback threads).
Brings with it some additional reusable core code:
1) Revised file functions: Reusable code that does things such as
safe path concatenation and parsing without buffer limitations or
data duplication. Variants that copy or alter the input path may be
based off these.
To do:
1) Put dircache functionality back in the sim. Treating it internally
as a different kind of file system seems the best approach at this
time.
2) Restore use of dircache indexes in the playlist and database or
something effectively the same. Since the cache doesn't have to be
complete in order to be used, not getting a hit on the cache doesn't
unambiguously say if the path exists or not.
Change-Id: Ia30f3082a136253e3a0eae0784e3091d138915c8
Reviewed-on: http://gerrit.rockbox.org/566
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
The plugin buffer was used only to avoid reparsing the playlist, so non-essential.
But when it was used it conflicted with the playlist viewer which already uses
the plugin buffer for playlist purposes simultaneously. It only works by
accident.
Since the reparse avoidance is non-essential don't do it for now. A temp buffer
can be passed to playlist_save() to enable it but the only caller (as of now)
does not do that.
Change-Id: I3f75f89d8551e1ec38800268b273105faba0efbf
This patch adds a configurable line separator between list items, very
similar to lists in Android. Additionally, below the list item there is a
thicker line. It can be disabled in the settings. Its color can
be configured as well.
Remote and monochrome displays are explicitly unsupported. If there is desire
this can be changed but it doesn't seem useful to me.
Change-Id: I005313b0d8f5ecd15864bf20e66ea4e3390d8b7d
In most of the translations strings with SYSFONT in title is
translated. This leads to displaying problem in (at least) graphical
equalizer due to the lack of non-latin character support in the
built-in font.
Change-Id: I0d27a5358e4eb539d4247c84975d8501d7668836
Reviewed-on: http://gerrit.rockbox.org/727
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
Add a "volume limit" parameter to the configuration file. The maximum
value of volume setting in sound menu will be limited to the same as
volume limit. Also each time when setvol() is excuted, Rockbox will
check if the global_settings.volume value larger than
global_settings.volume_limit. If larger, take the value of volume_limit
instead. The volume_limit argument shares the same maximum and minimum values
with volume argument, while taking the maximum volume as its default value.
Change-Id: I8ca9bc6ea6e617b48fc346aae5f2a0a1d259ae36
Reviewed-on: http://gerrit.rockbox.org/697
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
This was lost in 97a4c1ef (svn r30177) for unkown reason but the manual still
mentions this item, so I assume it was an accident. It doesn't hurt anyway.
Fixes FS#12930.
Change-Id: I2f5cd81913ec7bb911d1117e50c010a5c1b89b52
Since scrolling is now pixel-based this is not necessary anymore. custom line
height is handled by put_line() but can also possible to implement with
lcd_puts_scroll_func().
Change-Id: Iee9b12bf99afac93d95d2a1a6f5d5b4db237b21c
This is an improvement to the current compressor which I have added
to my own Sansa Fuze V2 build. I am submitting here in case others
find it interesting.
Features added to the existing compressor:
Attack, Look-ahead, Sidechain Filtering.
Exponential attack and release characteristic response.
Benefits from adding missing features:
Attack:
Preserve perceived "brightness" of tone by letting onset transients
come through at a higher level than the rest of the compressed program
material.
Look-ahead:
With Attack comes clipping on the leading several cycles of a transient
onset. With look-ahead function, this can be pre-emptively mitigated with
a slower gain change (less distortion). Look-ahead limiting is implemented
to prevent clipping while keeping gain change ramp to an interval near 3ms
instead of instant attack.
The existing compressor implementation distorts the leading edge of a
transient by causing instant gain change, resulting in log() distortion.
This sounds "woofy" to me.
Exponential Attack/Release:
eMore natural sounding. On attack, this is a true straight line of 10dB per
attack interval. Release is a little different, however, sounds natural as
an analog compressor.
Sidechain Filtering:
Mild high-pass filter reduces response to low frequency onsets. For example,
a hard kick drum is less likely to make the whole of the program material
appear to fade in and out. Combined with a moderate attack time, such a
transient will ride through with minimal audible artifact.
Overall these changes make dynamic music sound more "open", more natural. The
goal of a compressor is to make dyanamic music sound louder without necessarily
sounding as though it has been compressed. I believe these changes come closer to this goal.
Enjoy. If not, I am enjoying it
Change-Id: I664eace546c364b815b4dc9ed4a72849231a0eb2
Reviewed-on: http://gerrit.rockbox.org/626
Tested: Purling Nayuki <cyq.yzfl@gmail.com>
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
When using variadic macros there's no need for IF_MD2/IF_MV2 to deal
with function parameters. IF_MD/IF_MV are enough.
Throw in IF_MD_DRV/ID_MV_VOL that return the parameter if MD/MV, or 0
if not.
Change-Id: I7605e6039f3be19cb47110c84dcb3c5516f2c3eb
* Remove explicit tracking of elapsed time of previous track.
* Remove function to obtain auto skip flag.
* Most playback events now carry the extra information instead and
pass 'struct track_event *' for data.
* Tweak scrobbler to use PLAYBACK_EVENT_TRACK_FINISH, which makes
it cleaner and removes the struct mp3entry.
Change-Id: I500d2abb4056a32646496efc3617406e36811ec5
Update all .lang files and change the id from LANG_RECORDING_FREQUENCY
to LANG_FREQUENCY. Also update description and target.
It will throw things off for targets without recording but that do
have 48KHz, possibly older iPods. I'm not sure what else it might be
off hand. Regenerate voice files and replace .lang files in that case.
Change-Id: I9ab396ecfcca9206054bde34aa2cc23b505dabff
Replaces the NATIVE_FREQUENCY constant with a configurable frequency.
The user may select 48000Hz if the hardware supports it. The default is
still 44100Hz and the minimum is 44100Hz. The setting is located in the
playback settings, under "Frequency".
"Frequency" was duplicated in english.lang for now to avoid having to
fix every .lang file for the moment and throwing everything out of sync
because of the new play_frequency feature in features.txt. The next
cleanup should combine it with the one included for recording and
generalize the ID label.
If the hardware doesn't support 48000Hz, no setting will be available.
On particular hardware where very high rates are practical and desireable,
the upper bound can be extended by patching.
The PCM mixer can be configured to play at the full hardware frequency
range. The DSP core can configure to the hardware minimum up to the
maximum playback setting (some buffers must be reserved according to
the maximum rate).
If only 44100Hz is supported or possible on a given target for playback,
using the DSP and mixer at other samperates is possible if the hardware
offers them.
Change-Id: I6023cf0c0baa8bc6292b6919b4dd3618a6a25622
Reviewed-on: http://gerrit.rockbox.org/479
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
- Reduce the minimum step for EQ 'Gain' and EQ 'Q' values to .1dB
- Reduce the minimum step for EQ 'Precut' value to .1dB
Change-Id: I20712b3c769f9da4d6ed53c62d6a2a8352b6b269
Reviewed-on: http://gerrit.rockbox.org/414
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
Instead of 3 cfg lines per eq band there is now a single line
for each:
<config name>: <cutoff/center freq>, <q>, <gain>
In addition, the config value names make a bit more sense.
The old settings are still readable but config.cfg and any new
settings files will be written with the new config values. (The
old settings will be removed completly sometime after the next
stable release).
Also a slight rework of the advanced EQ menu UI
Change-Id: I9008658d36ded442a5f2f825916df42a3934cbef
Reviewed-on: http://gerrit.rockbox.org/394
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
- A 10 Band EQ for Rockbox w/ presets adapted
from VLC
- frequency stepping at 32, 64, 125, 250, 500
1K, 2K, 4K, 8K, 16K
Change-Id: I85ad84d70a534edfc66c6ad9af8a76f022a02ec7
Reviewed-on: http://gerrit.rockbox.org/386
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
HAVE_USB_CHARGING_ENABLE is not only used for software usb, so checking
for HAVE_USBSTACK is wrong.
Change-Id: I422796b517c262f33f35623e992434219e288424
Make set_sleep_timer a static function and only call
set_sleeptimer_duration externally, which is always called with minutes
values.
Change-Id: I985308bf014e354f91c47a0b2bf62f4f5a591919
Reviewed-on: http://gerrit.rockbox.org/327
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
Support multiple roots (i.e. scan folders) using the new folder_select()
function.
Amaximum of 12 dirs can be selected, however the setting (i.e. the entire
folder list) cannot be longer than 80 chars.
The setting works similar to the autoresume dirs: Directories are seperated
by colons, e.g. "/Music:/Podcasts". Default is "/sdcard" on android, "/" on
all other targets.
Changes are made to the multiple-root logic in tagcache.c. This is to
a) provide the logic at all on native targets and b) support more than
one root before the scan even starts (until now it was used to add roots
during scan due to symlinks).
Change-Id: I64992c0678324536e8e64cd4427c8abbd8e8b39e
Also move the definition to config.h
Change-Id: I36bb5020c5e06b2344292bc05e8c13ccc7a6a1ff
Reviewed-on: http://gerrit.rockbox.org/234
Reviewed-by: Nils Wallménius <nils@rockbox.org>
Moves replaygain definitions to lib/rbcodec/dsp/dsp_misc.h.
Intermediate functions in misc.c handle any adjustment and calling
the rbcodec APIs.
Change-Id: I9f03561bca9aedd13760cf19c4e19aa3c68e7024
Reviewed-on: http://gerrit.rockbox.org/140
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Creates a standard buffer passing, local data passing and messaging
system for processing stages. Stages can be moved to their own source
files to reduce clutter and ease assimilation of new ones. dsp.c
becomes dsp_core.c which supports an engine and framework for effects.
Formats and change notifications are passed along with the buffer so
that they arrive at the correct time at each stage in the chain
regardless of the internal delays of a particular one.
Removes restrictions on the number of samples that can be processed at
a time and it pays attention to destination buffer size restrictions
without having to limit input count, which also allows pcmbuf to
remain fuller and safely set its own buffer limits as it sees fit.
There is no longer a need to query input/output counts given a certain
number of input samples; just give it the sizes of the source and
destination buffers.
Works in harmony with stages that are not deterministic in terms of
sample input/output ratio (like both resamplers but most notably
the timestretch). As a result it fixes quirks with timestretch hanging
up with certain settings and it now operates properly throughout its
full settings range.
Change-Id: Ib206ec78f6f6c79259c5af9009fe021d68be9734
Reviewed-on: http://gerrit.rockbox.org/200
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
dsp_set_eq_coefs now has parameters for the band settings, so it doesn't
need to access global_settings.
Change-Id: I29ac19fc353b15a79cb25f0e45132aef0881e4c9
Reviewed-on: http://gerrit.rockbox.org/138
Reviewed-by: Nils Wallménius <nils@rockbox.org>
Where before there was a single sleep timer menu option which handled
initiating/ cancelling a sleep timer as well as setting the default duration,
now there is one menu option to either start or cancel a sleep timer and
another to set the default duration that will be used for future sleep timers.
Change-Id: Ibea3711ec6406845ff5d0c0568fe5d1739eb8deb
Reviewed-on: http://gerrit.rockbox.org/201
Reviewed-by: Nick Peskett <rockbox@peskett.co.uk>
Adds an option under settings > general settings > system to allow
the user to have the shortcuts menu displayed instead of the
quick screen. (option is "shortcuts instead of quickscreen" in the .cfg)
Change-Id: Id679b461c40ac617629422736d1509384364084d
Reviewed-on: http://gerrit.rockbox.org/199
Reviewed-by: Marek Salaba <marek.salaba@gmail.com>
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
When enabled, if the user has set "Start File Browser Here" (config.cfg:
start directory) to anything other than root and "Auto-Change Directory"
is set to "Yes" or "Random", the directory returned when an auto change
is required will be constrained to the value of "start directory" or below.
Change-Id: Iaab773868c4cab5a54f6ae67bdb22e84642a9e4b
Reviewed-on: http://gerrit.rockbox.org/182
Reviewed-by: Nick Peskett <rockbox@peskett.co.uk>
Tested-by: Nick Peskett <rockbox@peskett.co.uk>
The previous pseudo array access of separate members wasn't very
nice or clear.
Change-Id: I74a2b39bb9c71a1370a455c01c4d5a860765e040
Reviewed-on: http://gerrit.rockbox.org/179
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
* Introduce CONFIG_BATTERY_MEASURE define, to allow targets (application)
to break powermgmt.c's assumption about the ability to read battery voltage.
There's now additionally percentage (android) and remaining time measure
(maemo). No measure at all also works (sdl app). If voltage can't be measured,
then battery_level() is king and it'll be used for power_history and runtime
estimation.
* Implement target's API in the simulator, i.e. _battery_voltage(), so it
doesn't need to implement it's own powermgmt.c and other stubs. Now
the sim behaves much more like a native target, although it still
changes the simulated battery voltage quickly,
* Other changes include include renaming battery_adc_voltage() to
_battery_voltage(), for consistency with the new target functions and
making some of the apps code aware that voltage and runtime estimation
is not always available.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31548 a1c6a512-1295-4272-9138-f99709370657
A dedicated submenu for items which are run at startup, or initiate a shutdown.
Currently containing: Start Screen, Idle Poweroff, Sleep Timer & Start Sleep Timer on Boot.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31435 a1c6a512-1295-4272-9138-f99709370657
Use "type: time" and "data: talk" to have the time voiced when the shortcut is run.
use "type: time" and "data: sleep X" where X is the number of minutes to run the sleep timer for (0 means disable)
the name field is required
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31178 a1c6a512-1295-4272-9138-f99709370657
