Playing AAC-HE files resulted in a race condition between
audio/codec/buffering for set_cpu_frequency
Change-Id: I35e1c1fd18db623e2990c305acdca03f57184d0d
* Editing a bunch of drivers' thread routines in order to
implement a new feature is tedious.
* No matter the number of storage drivers, they share one thread.
No extra threads needed for CONFIG_STORAGE_MULTI.
* Each has an event callback called by the storage thread.
* A default callback is provided to fake sleeping in order to
trigger idle callbacks. It could also do other default processing.
Changes to it will be part of driver code without editing each
one.
* Drivers may sleep and wake as they please as long as they give
a low pulse on their storage bit to ask to go into sleep mode.
Idle callback is called on its behalf and driver immediately put
into sleep mode.
* Drivers may indicate they are to continue receiving events in
USB mode, otherwise they receve nothing until disconnect (they
do receive SYS_USB_DISCONNECTED no matter what).
* Rework a few things to keep the callback implementation sane
and maintainable. ata.c was dreadful with all those bools; make
it a state machine and easier to follow. Remove last_user_activity;
it has no purpose that isn't served by keeping the disk active
through last_disk_activity instead.
* Even-out stack sizes partly because of a lack of a decent place
to define them by driver or SoC or whatever; it doesn't seem too
critical to do that anyway. Many are simply too large while at
least one isn't really adequate. They may be individually
overridden if necessary (figure out where). The thread uses the
greatest size demanded. Newer file code is much more frugal with
stack space. I barely see use crack 50% after idle callbacks
(usually mid-40s). Card insert/eject doesn't demand much.
* No forcing of idle callbacks. If it isn't necessary for one or
more non-disk storage types, it really isn't any more necessary for
disk storage. Besides, it makes the whole thing easier to implement.
Change-Id: Id30c284d82a8af66e47f2cfe104c52cbd8aa7215
We don't really know what those are supposed to do. They seem to change the
volume curve but it is not very clear what is the intended purpose.
Change-Id: I65f5d18aba139844c23df092277ba17ee8518f96
sonynwz: quirk for cpufreq broken driver
There was some redundancy between frequency_linux(cpu, true) and
current_scaling_frequency(), also I see no reason to compile the cpuinfo stuff
unconditionally and the scaling info only on DX since it was already printed
some partial scaling info anyway. Thus compile all the code unconditionally
and simplify the logic in the debug menu. Also avoid putting buffers of size
PATH_MAX on stack since it can be quite big and we only requires 64 bytes
for those paths.
On Sony NWZ, the cpu driver reports frequency in MHz instead of kHz thus we need
to make the cpuinfo code aware of that bug.
Change-Id: I61af45ab5f179ecc909b4841b9137a915a60193a
We still miss the model IDS for those device so scsitool won't be able to
recognize them automatically.
Change-Id: I17ae0f0d95c011cea8e289def63c7673b6c4b667
Always compile in pcm_alsa_set_digital_volume, the linker will optimize it
away on targets that don't use it.
Change-Id: Ia21c3eaa8a64b75761ab5d056361e7ed1fcf949a
Due to some undocumented behavior, the touchscreen was almost unusable in point
mode. Now it's much better but still not very nice to use, probably it needs some
filtering.
Change-Id: Idc8a0214b09f268e6be907ee6ec3126cc0d88773
This requires a few changes unrelated to the A860 because configure unsets
APPLICATION but the NWZ is an application!
Change-Id: Id91aa23193383ac95886b281653da5286edd9caf
SUPPORTED SERIES:
- NWZ-E450
- NWZ-E460
- NWZ-E470
- NWZ-E580
- NWZ-A10
NOTES:
- bootloader makefile convert an extra font to be installed alongside the bootloader
since sysfont is way too small
- the toolsicon bitmap comes from the Oxygen iconset
- touchscreen driver is untested
TODO:
- implement audio routing driver (pcm is handled by pcm-alsa)
- fix playback: it crashes on illegal instruction in DEBUG builds
- find out why the browser starts at / instead of /contents
- implement radio support
- implement return to OF for usb handling
- calibrate battery curve (NB: of can report a battery level on a 0-5 scale but
probabl don't want to use that ?)
- implement simulator build (we need a nice image of the player)
- figure out if we can detect jack removal
POTENTIAL TODOS:
- try to build a usb serial gadget and gdbserver
Change-Id: Ic77d71e0651355d47cc4e423a40fb64a60c69a80
The ZEN/X-Fi (STMP3700) don't handle memory frequency scaling really well, for
this reason we run it at a fixed frequency. That frequency was previously set
to 64Mhz because when the CPU run at its lowest frequency, we set the VDD voltage
to 0.975 V and on STMP3700, VDDD=VDDDMEM and this is too low to run EMI at 130Mhz.
This is not a good solution because under heavy load, running the EMI at 64Mhz
results in frame drops and a sluggish device. Thus we now run the EMI at 130Mhz
all the time now. To do so, increase the minimum VDD voltage to 1.275 V.
This may result is a decreased battery life on those targets but it will also
avoid all sorts of glictches and all the device to truly run at full speed.
Change-Id: Ia8391492c29fe67bc2701aa7d8cfd00a9df349e8
One cannot call lradc_acquire in IRQ context. The solution is to reserve the
channel once at init. There is an additional complication on STMP3600 where
channel mapping is fixed.
Change-Id: Idccbac634a4d9002703e2b1d57748beb9b245cbb
After compiling the ypz5 target, I have discovered that the keypad
system was refusing to compile, due to a much newer button API.
This patch adapts the target to the current imx233 implementation.
Additonally, some ADC button values have been re-adjusted.
Change-Id: Ib9bfd6aeec5e9e8dfef5887c4147201dd9028a44
si4700_rds_process() should only be called on the rising edge of
RDSR since it now rejects segments out of sequence. Receiving the
same segment multiple times due to rapid polling is of course out
of sequence so do no more processing until RDSR bit cycles to
avoid repeatedly sending the same data instance.
I don't have the tools installed to test compile so there could be
typos. However, I tested on gigabeat-s with YPR0 setup copied over
and it fixed the issue with PS and RT.
Change-Id: Iab511bef64030de8c07d4d22dcf338c8720e2ae2
- Fix broken recording from jack microphone.
- Fix recording hardware detection on models that do not support
the jack microphone.
- Enable monitor mode when recording.
Change-Id: Ib79a2746f2d75f74cf6667d33bc9ed6512bbc8a9
Many includes of fat.h are pointless. Some includes are just for
SECTOR_SIZE. Add a file 'firmware/include/fs_defines.h' for that
and to define tuneable values that were scattered amongst various
headers.
Remove some local definitions of SECTOR_SIZE since they have to be
in agreement with the rest of the fs code anyway.
(We'll see what's in fact pointless in a moment ;)
Change-Id: I9ba183bf58bd87f5c45eba7bd675c7e2c1c18ed5
As preparation to add new targets to the s5l8702 directory,
rename files as:
s5l8702/ipod6g/*-ipod6g.c -> s5l8702/ipod6g/*-6g.c
Change-Id: I0cd03d6bcf39b2aa198235f9014cb6948bbafcd5
* Remove unused bits like the radio event and simplify basic
radio interface. It can be more self-contained with rds.h only
required by radio and tuner code.
* Add post-processing to text a-la Silicon Labs AN243. The chip's
error correction can only do so much; additional checks are highly
recommended. Simply testing for two identical messages in a row
is extremely effective and I've never seen corrupted text since
doing that, even with mediocre reception.
Groups segments must arrive in order, not randomly; logic change
only accepts them in order, starting at 0.
Time readout was made a bit better but really we'd need to use
verbose mode and ensure that no errors were seen during receiving
of time and more checks would be need to have a stable PI. The
text is the important bit anyway.
* Time out of stale text.
* Text is no longer updated until a complete group has been
received, as is specified in the standard. Perhaps go back to
scrolling text lines in the radio screen?
* Add proper character conversion to UTF-8. Only the default G0
table for the moment. The other two could be added in.
* Add variants "RDS_CFG_PROCESS" and "RDS_CFG_PUSH" to allow
the option for processed RDS data to be pushed to the driver and
still do proper post-processing (only text conversion for now for
the latter).
Change-Id: I4d83f8b2e89a209a5096d15ec266477318c66925
On Windows 64-bit, the size of long is 32-bit, thus any pointer to long cast is
not valid. In any case, one should use intptr_t and ptrdiff_t when casting
to integers. This commit attempts to fix all instances reported by GCC.
When relevant, I replaced code by the macros PTR_ADD, ALIGN_UP from system.h
Change-Id: I2273b0e8465d3c4689824717ed5afa5ed238a2dc
Running at 130MHz is unsafe since on those targets, we disable memory frequency
scaling because it is unstable. That leads to situation where cpu is running at
64MHz and VDD is at 1.050V. But on STMP3700, the EMI uses the VDD rail instead
of a dedicated VDDMEM rail as on STMP3780. Thus we are essentially running the
EMI at 130MHz at 1.050V when the minimum recommened voltage is 1.2V. This commit
runs the EMI at 64MHz all the time on the ZEN and ZEN X-Fi which will lead to
reduce performance but hopefully increases stability.
Change-Id: Ida6c2ec130b1778973e383d7c44a06a6ca8f9268
This feature was never used and it is not even working because weak linking
doesn't work in-between files in a library.
Change-Id: I389ea5f17be1d9db0e2150828d704be5a091e09d
