MCI_RESPONSE_ERROR covers MCI_CMD_TIMEOUT & MCI_CMD_CRC_FAIL and makes it more clear that these are errors in the response and not the command itself.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24003 a1c6a512-1295-4272-9138-f99709370657
Both the internal and uSD cards are now put into 4 bit widebus mode during initialization except for bootloader.
Add MCI_START_BIT_ERR to MCI_ERROR list and change name to MCI_DATA_ERROR for clarity.
Make appropriate changes to SD error codes.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23977 a1c6a512-1295-4272-9138-f99709370657
This patch changes all references/assumptions of PCLK to IDE_CLK for the internal pl180 controller.
Lower the AS3525_IDE_FREQ to 50 MHz in order to be able to divide by 2 for 25 MHz on the internal SD card.
Adjust the code in debug-as3525.c to account for the change and the frequencies reported should be correct.
Add some #if defined(HAVE_MULTIDRIVE) conditionals to cut out the code dealing with uSD for the clip.
Isolate the write delay needed for low frequency writes to only run for standard speed uSD cards. That is the only case for an MCICLK at 15.5 MHz.
Internal cards run at 25 MHz, HS uSD at 31 MHz, and standard speed uSD cards at 15.5 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23929 a1c6a512-1295-4272-9138-f99709370657
Some cards need this delay now that we're running at ident speed during this part of the init stage.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23919 a1c6a512-1295-4272-9138-f99709370657
Addition of a small write delay avoids data crc failures at lower MCICLK frequencies.
Check the actual speed value from the card's CSD register to determine HS status. HS cards can run at twice the speed of standard speed SD cards.
Internal cards & standard speed uSD now run at PCLK/4 = 15.5 MHz. HS uSD cards run at PCLK/2 = 31 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23901 a1c6a512-1295-4272-9138-f99709370657
It seems that lowering the operating frequency for the SD cards has made some uSD cards have problems with the init process.
By moving the boost from ident to operating frequency to after the switch to HS timing these card now seem to init normally.
We still need to fix the problem where the internal cards and non HS uSD cards are still slightly overclocked at 31 MHz.
As of now we experience data crc failures during writes at the next lower frequency of 15.5 MHz.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23870 a1c6a512-1295-4272-9138-f99709370657
This is within the SD Spec for v2 High Speed cards but still over the 25 MHz limit for v1 and non-HS v2 cards.
Test_disk write & verify passes on both internal and uSD.
The v1 cards still need to be lowered to 15 MHz but that causes data crc failures at this point.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23835 a1c6a512-1295-4272-9138-f99709370657
Currently the bypass bit is not cleared so it's possible to enter the identification phase at bypass speed instead of ident speed.
The simplest solution to ensure the bypass bit is not set is to set the register with an = operation instead of |=.
This makes setting the MCI_CLOCK register at the end of the controller init unnecessary.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23830 a1c6a512-1295-4272-9138-f99709370657
bits 13:0 must not be modified (except for bit 8 ?)
fixes FM on my Clipv1 (some Clips weren't affected)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23826 a1c6a512-1295-4272-9138-f99709370657
If the controllers were already enabled there was a chance we could try to read the MCI_CLOCK registers while the cards were buffering and then disable the controllers prematurely.
I guess funman knows and sees all!! Thanks funman.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23811 a1c6a512-1295-4272-9138-f99709370657
Because we turn off the clocks to the SD controllers between disk accesses we were unable to read the MCI_CLOCK registers until there was a disk access. Now we can read them immediately.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23810 a1c6a512-1295-4272-9138-f99709370657
Enabling/disabling of the NAF and IDE clocks is now grouped together as both are related to the internal SD.
Sequence for disabling SD now mirrors the enable sequence.
Comments added to make it easier to follow the configuration change for XPD from gpio to mci-sd and back.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23808 a1c6a512-1295-4272-9138-f99709370657
- Use the fact that unicode code currently does not support chars above 0xffff
(see utf8decode()), and change diacritic database's char code type to
unsigned short from int. Also comment out database entries above unsupported
range.
- Use const when possible.
- Iterate over buffer using the buffer's pointer, thus avoiding usage of some
variables, and avoiding multiple access to the same array item.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23776 a1c6a512-1295-4272-9138-f99709370657
- Fix bug which cause wrong placement of characters in some specific conditions
- Fix multiple similar entries in cache
- Protect against negative x values passed to drawing function
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23765 a1c6a512-1295-4272-9138-f99709370657
