What works:
- LCD: 16-bit RGB565
- all buttons, including scrollwheel
- SD Card
- Battery level and charging/not charging status
- USB
- audio
- sample rate switching
- HP / LO detect, with "safe" fixed LO volume -
LO volume will only be put to user-defined max volume
if headphones are not present.
- rtc
- Plugins build, tried a couple and they seem OK
- Bootloader, installable to nand via usbboot
What doesn't work:
- Dual Boot
- power on/off has intermittent, low volume audio click
(sometimes it's completely silent, sometimes there's
a click)
- Audio uses 16-bit volume scaling, so clicking/popping
is pretty bad at lower volumes - need 32 bit volume
scaling, 24 bit I2S data
- USB HID keys not yet defined
- no jztool support
Unknowns:
- Stereo Switch pins: Direction select, AC_DC
(probably not even hooked up)
- What is the actual purpose of the Stereo Swtich?
- How does the bluetooth module connect?
"Someday" stuff:
- get LCD working at higher bit depth
- Bluetooth
Change-Id: I70dda8fc092c6e3f4352f2245e4164193f803c33
- Audio playback works
- Touchscreen and buttons work
- Bootloader works and is capable of dual boot
- Plugins are working
- Cabbiev2 theme has been ported
- Stable for general usage
Thanks to Marc Aarts for porting Cabbiev2 and plugin bitmaps.
There's a few minor known issues:
- Bootloader must be installed manually using 'usbboot' as there is
no support in jztool yet.
- Keymaps may be lacking, need further testing and feedback.
- Some plugins may not be fully adapted to the screen size and could
benefit from further tweaking.
- LCD shows abnormal effects under some circumstances: for example,
after viewing a mostly black screen an afterimage appears briefly
when going back to a brightly-lit screen. Sudden power-off without
proper shutdown of the backlight causes a "dissolving" effect.
- CW2015 battery reporting driver is buggy, and disabled for now.
Battery reporting is currently voltage-based using the AXP192.
Change-Id: I635e83f02a880192c5a82cb0861ad3a61c137c3a
This streamlines the boot code a bit and reduces target specific
boilerplate. The clock init hack used by the bootloader has been
"standardized" and works for the main Rockbox binary now, so you
can boot rockbox.bin over USB without special hacks.
Change-Id: I7c1fac37df5a45873583ce6818eaedb9f71a782b
SPL and UCL-compressed bootloader are now packed into one output,
bootloader.m3k, eliminating the separate SPL build phase.
The Rockbox bootloader now has a recovery menu, accessible by
holding VOL+ when booting, that lets you back up, restore, and
update the bootloader from the device.
Change-Id: I642c6e5fb83587a013ab2fbfd1adab439561ced2
- Removed unnecessary layers of generic code
- Software ECC is gone since we don't need it now (and maybe not ever)
- Removed bounce buffering, so callers must now align buffers
Change-Id: I33fbac9d9d12a4657980b8618c7d62bfa91e2ea0
This overwrote the first 2 instructions of crt0 in the bootloader!
I'm really not sure how this *didn't* cause a fatal exception.
This address isn't special as far as I know, so just move it to the
TCSM by making it a static variable.
Change-Id: I58e1486804aeb2b68325e8de2aa1874c97abef19
Initializing the clocks in the SPL brings Rockbox in line with
how the FiiO M3K's original SPL works. It's likely other X1000
devices do this too.
There was a logic error in the previous setup: the code falsely
assumed that DDR memory would always be running from MPLL, but
it would be switched to APLL by the bootloader. Rockbox would
then try to re-init APLL, albeit with the same parameters. Maybe
this was the cause of the boot hang on some units.
Change-Id: I64064585e491bbdf1e95fe9428c91a9314f2a917
SPL is now designed so core X1000 code is in control of the boot,
under the reasonable assumption that the device boots from flash.
It should not be too hard to adapt to other X1000 ports.
The biggest functional change is that the SPL can now read/write
the flash, under the control of a host computer. The SPL relies
on the boot ROM for USB communication, so the host has to execute
the SPL multiple times following a protocol.
Change-Id: I3ffaa00e4bf191e043c9df0e2e64d15193ff42c9
