The current code uses the msec irq to collect statistics and
detect irq storms (debug). But this irq is triggered 1000 times
per sec and we don't need that accuracy. This commit removes the
msec irq and use the tick timer instead which is triggered only
100 times per second.
Change-Id: If14b9503c89a3af370ef322678f10e35fafb4b8a
The lcd driver does not wait for the refresh to be done to return
from lcd_update(). This means that changing a register is unsafe
if done in the middle of the redraw. This could happen when
disabling the lcd for example. Make sure it doesn't happen by
waiting for the lcdif to be ready.
Change-Id: I43ec62a637dd61c3b2a3a6e131c1a9e8035524b1
When changing the cpu frequency, it is important to make sure that
HBUS stays at a reasonable frequency otherwise the chip will
crash. Special care is needed about auto-slow and clk_p/clk_h
ratio on intermediate steps.
Change-Id: Ief9f68ddf286caabe75c879718dac5027ab1560f
Make sure DCDC is running at boot (it is disabled by default when
5V is present and we don't want to rely on the bootloader to
change this).
When changing the voltage on a regulator, it usually takes 2ms for
the voltage to stabilize. In DCDC mode, there is an irq to notify
about the event so use it ! This is especially important when
changing cpu frequency because increasing the cpu freq while the
voltage is rising is unreliable.
Change-Id: Icfe9ef3ee90156d1e17da0820d9041859f7f3bca
HBUS uses the same field for integer and fractional dividers, the
choice is made by a bit. Make sure both are changed together,
otherwise this could result in the wrong divider to be used and in
HBUS freq to be too low or too high (very bad).
Change-Id: I253d8eeee26c5038868b729c4f791511295a39f0
Use %x9(id) to draw an image in the whole current viewport using the
9 segment drawer (which draws the corners as normal and *tiles*
the middle segments to the needed width/height).
Future work is to make it scale instead of tile
Change-Id: Ic3ed1cad93f96091694801eb442e0da5a2401203
Some USB controllers like the one of the Rockchip 27xx handle some
requests in pure hardware. This is especially a problem for two
of them:
- SET ADDR which is used by our core to track the DEFAULT/ADDRESS
state and is required for the drivers to work properly
- SET CONFIG which is used by our core to initialise the drivers
by calling init_connection()
In these cases we need a way to notify the core that such requests
happened.
We do this by exporting two functions which directly notify the
core about these requests and perform the necessary init steps
required without doing the actual USB transfers. Special care is
needed because these functions could be called from an interrupt
handler. For this reason we still use the usb_queue and introduce
new IDs so that they are processed in order and safely.
No functional change is intended, both in the usbstack and on
targets without such quirks.
Change-Id: Ie42feffd4584e88bf37cff018b627f333dca1140
* Adds some additional niftyness like a floating popup display that
is implemented in an OSD library for use by other plugins.
* Speed changes are now gradual for both views and follow a curve
derived from some fiddling around to get a nice feel.
* Refined a few behavioral things overall.
It needs a bit of help from a direct PCM channel callback so it may
capture PCM for waveform display. Also need a few other core routines
to help out for the OSD.
Messes with some keymaps. Some targets need keymaps to access the
different views. Some devices can't support the additional view
because it requires a large buffer ( > 1 s) for samples.
If the plugin buffer is small, they can still use the popup display
since the plugin is also much smaller in that case.
Slow speed waveform needs some refining so it draws gradually like
a real oscilloscope but I'll stick with what it is, for the moment.
Change-Id: Ieb5b7922a2238264e9b19a58cb437739194eb036
Reviewed-on: http://gerrit.rockbox.org/245
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
Ideally someone will go through and make a graphic for the 6G, but as it looks nearly identical to the Video its not a huge deal.
Change-Id: If507c6d4f01eb0b1e5fc2f15f6a0e5a3195006c6
Uninitialized struct scroll which is used to pass state between
scrollstrip ISR and button_read_device() can bomb out whole
button subsytem.
Change-Id: I3b415c22cfee4181b2132cddaeff68797c7cc0ea
If interrupts trigger during cache invalidation this could cause memory
corruption. This should be right fix for commit_discard_idcache in
contrast to 72ebcbf and c1ec1ec.
Change-Id: I141fb585004d4a1967b0a03bc37db3964d886564
Reviewed-on: http://gerrit.rockbox.org/345
Tested-by: Andrew Ryabinin <ryabinin.a.a@gmail.com>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
It seems something wrong with cache handling in rk27xx. OF always disable cache
before invalidating cache ways, therefore, now we do the same.
Hopefully this will fix cache handling, but I couldn't contend that it's really so.
Change-Id: I967c18211f0ddff689b6a17579fbe8685277f132
This is work from FS#12431 synced to current HEAD and slightly
tweaked (gcc 4.6.2 -> 4.6.3, binutils 2.21.1 -> 2.22)
Change-Id: I76af91e80ac2a9c16a776c7f0a33cc51603bbf9b
The running count is only 16-bit wide, since the always tick
setting derives from the crystal clock at 24MHz the user timer
cannot be set lower than ~300Hz which is already too high.
Switch to the 32KHz crystal source to fix this.
Change-Id: Ie7775460b17ea7ab331738734e3d688ad5563857
Several HM-801 DAPs have another buttons circuit.
This patch adds support for such devices so they could work properly.
Change-Id: Ic49e8e46b3e785b91c7c4706003fac3dbc20ae59
Uses register polling method to decide when it's time to decode
RDS packets.
Change-Id: I1d3cc995ea3350ec7b101438b8f2027130d4a4c9
Reviewed-on: http://gerrit.rockbox.org/320
Reviewed-by: Lorenzo Miori <memorys60@gmail.com>
Tested-by: Lorenzo Miori <memorys60@gmail.com>
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
Tested-by: Thomas Martitz <kugel@rockbox.org>
Make set_sleep_timer a static function and only call
set_sleeptimer_duration externally, which is always called with minutes
values.
Change-Id: I985308bf014e354f91c47a0b2bf62f4f5a591919
Reviewed-on: http://gerrit.rockbox.org/327
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
Previously TIMEOUT_BLOCK would be handled the same as TIMEOUT_NOBLOCK, i.e.
poll only without thread switch, which is rather unexpected from *_w_tmo()
functions. No current code doesn't call it that way yet.
Change-Id: I370ce0f752681122d197eadeee9ab17112647c20
We should cast to (volatile uint32_t*) here, because attempt to refer to volatile
object through use of an lvalue with non-volatile-qualified type will result in
undefined behavior.
Change-Id: I1b2e9688af11d3dcba518a5e31865d703b54b635
Use DMA engine for fullscreen updates and bypass mode for partial
updates. This gives major boost on rk27generic:
default ARM:AHB:APB 200💯50
HEAD 1/1: 26.3fps 1/4: 105.0fps
patched 1/1: 116.5fps 1/4: 249.5fps
with freq scalling NORMAL mode ARM:AHB:APB 50:50:50
HEAD 1/1: 13.1fps 1/4: 52.5fps
patched 1/1: 54.5fps 1/4: 119.0fps
Tested on rk27generic noname DAP and on Hifimans.
Change-Id: Id9dd4d2d61542c7ea6b5c6336b170d6357cefde9
This version resembles how OF handle cache invalidates.
This seems to fix mysterious data aborts on plugin/codec loading
after introducing frequency scaling.
Credit goes to mortalis for pinpointing the reason of aborts.
Change-Id: I3477b3f65d593d7b43c36a0b06d863f71f000812
The functions document my reverse engineer findings about nand
controller. This code is commented out and is purely for reference
as FTL scheme is still unknown.
Change-Id: I70edeb4bfb0cbd51b6adc15afa7193dd8f71e8da
Frequency scaling seems to be unstable and causes the device to
freeze. It is unclear why at the moment, perhaps we need to ramp
up the vddd voltage to avoid a false brownout ?
Change-Id: I7aaea9d7c213922a65250fe50775fb785d430226
