Similar to the native port, the hosted port benefits from
adding a -1 dc bias to the PCM data. This prevents almost
all clicking artifacts.
Change-Id: Ic6378716774b6d88df23c476e2ef54d49f33dc72
A small negative offset seems to silence all
play/pause clicking on the PCM5102A.
Also adding PCM soft muting, and muting the headphone amp
when the headphones are detected as removed. This has been
tested to not cause any unintended side effects on the
line out.
Also confirmed the numerical dB values are (approx.) correct.
Change-Id: I689d68887c86add9cc5e0ccb0c7de01aaa69b4d9
* It had a (read) buffer overflow when dumping the stuff on the back half of the buffer
* a highly questionable code construct was nuked
Change-Id: I7f6f119524fc2095f788fc9b3d356459955d3ace
What works:
- LCD: 16-bit RGB565
- all buttons, including scrollwheel
- SD Card
- Battery level and charging/not charging status
- USB
- audio
- sample rate switching
- HP / LO detect, with "safe" fixed LO volume -
LO volume will only be put to user-defined max volume
if headphones are not present.
- rtc
- Plugins build, tried a couple and they seem OK
- Bootloader, installable to nand via usbboot
What doesn't work:
- Dual Boot
- power on/off has intermittent, low volume audio click
(sometimes it's completely silent, sometimes there's
a click)
- Audio uses 16-bit volume scaling, so clicking/popping
is pretty bad at lower volumes - need 32 bit volume
scaling, 24 bit I2S data
- USB HID keys not yet defined
- no jztool support
Unknowns:
- Stereo Switch pins: Direction select, AC_DC
(probably not even hooked up)
- What is the actual purpose of the Stereo Swtich?
- How does the bluetooth module connect?
"Someday" stuff:
- get LCD working at higher bit depth
- Bluetooth
Change-Id: I70dda8fc092c6e3f4352f2245e4164193f803c33
I'm not happy with the proliferation of filter-roll-off options
but I don't have a less ugly solution.
Change-Id: I740fca006fa0c3443a467acfea55b6574d48346b
- Audio playback works
- Touchscreen and buttons work
- Bootloader works and is capable of dual boot
- Plugins are working
- Cabbiev2 theme has been ported
- Stable for general usage
Thanks to Marc Aarts for porting Cabbiev2 and plugin bitmaps.
There's a few minor known issues:
- Bootloader must be installed manually using 'usbboot' as there is
no support in jztool yet.
- Keymaps may be lacking, need further testing and feedback.
- Some plugins may not be fully adapted to the screen size and could
benefit from further tweaking.
- LCD shows abnormal effects under some circumstances: for example,
after viewing a mostly black screen an afterimage appears briefly
when going back to a brightly-lit screen. Sudden power-off without
proper shutdown of the backlight causes a "dissolving" effect.
- CW2015 battery reporting driver is buggy, and disabled for now.
Battery reporting is currently voltage-based using the AXP192.
Change-Id: I635e83f02a880192c5a82cb0861ad3a61c137c3a
Atmel AT88SC6416C CryptoMemory is almost I2C compatible. The device
is connected to bitbanged I2C bus shared with compliant I2C devices.
Change-Id: Iec54702db1bdfb93c01291eef18ec60391c63b16
Do not introduce any change for M:Robe 500 as it uses the two LCD frames
in non-obvious way.
Sansa Connect and Creative ZVM use only single front framebuffer.
Place TTB at DRAM end to minimize memory loss due to alignment.
Reserve as little as possible memory for the LCD frames.
On Sansa Connect this change extends audio buffer by 858 KiB.
Change-Id: I21bdeec4cfba86d71803a39acd651a87e73767e6
This eliminates the dependence on a special struct since we were only
using the modtime anyway. But it no longer fits any known standard APIs
so I have converted it to our own extension instead. This can still be
adapted to existing hosted APIs if the need arises.
Change-Id: Ic8800698ddfd3a1a48b7cf921c0d0f865302d034
This emulates the traditional utime function from UNIX clones to allow
for manual updates of the modification timestamp on files and directories.
This should only prove useful for non-native targets as those usually
have a libc version of utime.
Change-Id: Iea8a1d328e78b92c400d3354ee80689c7cf53af8
Make it possible for target to provide voltage, percentage and time to
empty values. The voltage measurement is nice to have in debug menu even
if the actions are taken only based on percentage. Perform battery level
estimation based on voltage only if percentage is not available.
Use time to empty based on actual power consumption. This makes the
estimated runtime displayed in Rockbox Info to react to backlight
setting. The bq27000 updates time to empty estimate every 5.12 seconds
so it is possible to see the estimate with backlight off on the screen
if user enters Rockbox Info, activates hold switch, waits 11 seconds and
releases the hold switch.
Change-Id: Iafe3fa0fb334e3428e3a0ad05b2c020d208dc934
Prevent startup screen flash by properly using AVR LCM functions. Power
off LCD when not needed to improve battery runtime.
Change-Id: I76e3c5c0208774f189fbc6f7d7b3c9e22c062285
Import non-free firmware image from linux-firmware package.
Firmware loading works but is disabled at compile time because just
loading firmware without configuring device results in higher power
consumption without any benefit to end user.
Change-Id: I8fd252c49385ede1ea4e0f9b1e29adeb331ab8ae
This moves the time conversion function to timefuncs since it has
uses on ports that don't use the FAT driver. This function has no
dependency on the FAT driver as it is so this should not cause any
issues. To reflect this separation the function was renamed to
dostime_mktime since it is really for DOS timestamps. The places
where it was used have also been updated.
Change-Id: Id98b1448d5c6fcda286846e1d2c736db682bfb52
Use 32-bit monotime AVR counter for time tracking. Set the time by
adding fixed offset to the counter value. Store the offset in rockbox
directory to make it persistent between reboots.
Do not implement alarm functionality as wakeup is only possible from
sleep and not from complete power off.
Change-Id: I615c7eb4df8ab0619dcbfcff107bc7051a15aace
Consider battery level down to 0 as safe as OF continues to operate
normally even when at level 0.
Change-Id: Ie3889e5662b9fa6588e20ad02d8953f29e28800c
Wait on semaphore until DMA finishes instead of busy waiting. This
allows the CPU to be used by other tasks during transfers.
Increase peripheral clock frequency, divide AHB by 2 instead of 3.
Function clock frequency is AHB divided by MMC divider + 1.
Change-Id: Ic890634da7e3541962ea3501eae8fa2ca2db606a
On devices that can assign interrupt IN, bulk IN and bulk OUT endpoints
this change results in the serial interface working out of the box on
Linux and Windows. On Linux it is registered as ttyACM device and on
Windows it is assigned a COM port number.
On devices that cannot assign the interrupt IN this change won't have
any effect.
Implement minimum required interface control requests. Respond with
whatever line coding was set to make terminal programs happy.
Change-Id: Id7d3899d8546e45d7cb4ecc3fe464908cb59e810
Allows for the i2c boilerplate to be shared between the M3K and
Shanling Q1 ports. M3K-specific quirks remain in button-fiiom3k.
Change-Id: I8879b603cefc16416bb200f1c484ca916d935c6a
Acknowledge SYS_USB_CONNECTED in all queues so USB task can gain
exclusive access to the storage.
Reduce CPPI requeue timeout to speed up disk access.
Change-Id: I322aae4cac679696bb8186ccacf838a18f0715e9
Port USB driver from Sansa Connect Linux kernel sources. The device
successfully enumerates and responds to SCSI commands but actual disk
access does not work. The SCSI response sent to host mentions that both
internal storage and microsd card are not present.
Change-Id: Ic6c07da12382c15c0b069f23a75f7df9765b7525
The old name was a bit misleading. AXP173 is sort of the lowest common
denominator of a series of related chips. The M3K uses an AXP192 which
has a few extra features vs. the AXP173.
New voltage regulator stuff was added for the sake of the Shanling Q1
native port (that player also uses an AXP192).
Change-Id: Id0c162c23094bb03d13fae2d6c332e3047968d6e
Some audiohw API calls are shared between playback and recording,
eg. frequency settings. Implementing these in the DAC driver won't
work for the M3K, as it uses a separate codec for microphone input.
Change-Id: Ieb0a267f8a81b9e2bbf0bbca951c5778f8dcd203
- Add support for skip and seek while the player is locked.
(Thanks to @bahus for the suggestion)
- Fix touch zones because the down button zone ended up being
a lot smaller than expected due to the touchpad's wonkiness.
Also added a visual display of the touchpad to its debug menu.
- Fixes the pictureflow keymap because it was mostly unusable.
Change-Id: Ic0da4f8df3613ff7828ce1cb940ed9e77ada3281
Also bump max battery capacity to 7300mAh, to accomodate
oversized aftermarket units that require case mods.
Change-Id: I743e550b0c0843ab17529e70b5d592ea0e9a79d8
- Move WPS Stop to Power (Hold)
- Add WPS Hotkey to Wheel scroll Fwd/Back
- Add WPS Quickscreen to Play (Hold)
- Add Tree Hotkey to Play (Hold)
Change-Id: Id74622138353521f736c0de1009a354307b108eb
SPL and UCL-compressed bootloader are now packed into one output,
bootloader.m3k, eliminating the separate SPL build phase.
The Rockbox bootloader now has a recovery menu, accessible by
holding VOL+ when booting, that lets you back up, restore, and
update the bootloader from the device.
Change-Id: I642c6e5fb83587a013ab2fbfd1adab439561ced2
It never worked, and hasn't compiled in something like a decade, Given
the HW capabilities (limited onboard flash, no expandability) there's
really no point in trying to fix/complete it.
Change-Id: I7d175089840396f8891645bd10010d730dd5bfdc
They were never finished, never saw any release ever, and haven't
compiled for the better part of a decade. Given their HW capabilities [1],
they are not worth trying to fix.
[1] 1-2MB RAM, ~256MB onboard flash, no expandability
Change-Id: I7b2a5806d687114c22156bb0458d4a10a9734190
Although data transfer is reliable with DMA, it seems to cause hangs
and lockups during the early stages of connection and it's not clear
what the cause might be.
Change-Id: I9a83089c31d28309f0534dcdedf3c8c8348e6e3d
This only required a minor patch to the usb-designware driver due
to DMA requiring physical addresses -- on the X1000, these differ
from virtual addresses so we have to do the usual conversion.
Both the mass storage and HID drivers work, but there are a few
issues so this can't be considered 100% stable yet.
- Mass storage might not be detected properly on insertion,
and USB has to be replugged before it shows up
- HID driver may occasionally panic or hang the machine
Change-Id: Ia3ce7591d5928ec7cbca7953abfef01bdbd873ef
- Added register names to reduce usage of magic numbers
- Added function to control max charging current, needed for USB
- Corrected comment about axp173, since FiiO M3K has an axp192
Change-Id: I6604ce8d44e5a2ee84061cf042d17ccc4734ac57
After conducting some simplistic tests, I found that the power usage
did not appear to be affected by the CPU frequency.
I tested by playing back a 44.1 KHz FLAC file on single track repeat,
and measured current with the AXP173's battery discharge current ADC.
The button and LCD backlights were set to always on. Headphones were
unplugged and the volume was muted to eliminate any influence from
the headphone amp.
On average the current usage was between 78-81 mA at 1008 MHz, 252 MHz,
and 112 MHz. If anything, 1008 MHz drew _less_ current than the lower
frequencies, by about 1-3 mA.
A possible explanation for this, assuming it's not just a bias of the
test, is that the CPU idle state saves so much power that it's better
to maximize the real time that the CPU spends idling. More systematic
testing is needed to confirm this.
Change-Id: I527473e8c4c12bc1e94f8d4e849fecc108022abe
Tested on eros q, everything measured from line out,
open circuit.
- volume steps were approximately double the dB they
were labelled as, so "-2 dB" would result in a change
of about -4 dB from maximum (0, +6.2dBV)
- maximum volume defining the line out volume only
changed every 10 values, and then was not close
to correct- "-10 dB" resulted in -2.5 dB from maximum
This gets the volume dB approximately correct, and
maximum volume correctly sets the line out volume.
I was unable to get odd values in the max volume
to work, so set the step size to 2 instead of one.
For "consumer level" (-10dBV), set to -16.
For "Pro level" (+4dBu -> ~1.8dBV), set to -4.
Change-Id: I898b85d768153579a893b23551019af88f865d21
Including direct use of the external SD card mount
Known issue: If SD card is inserted at startup, it must be
ejected and reinserted to be registered.
Change-Id: I5f420160bda32135cbb088c1e8b04b6e3a73018e
(Don't include rbpaths.h in settings.h, or string-extra.h in rbpaths.h)
Build-tested on rocker, erosq, mini2g, nano2g,
xduoox3, clipzip, dx50, and uisim
Change-Id: If32e9c9910f5c8247a655cb64522b84d6d7ccbb5
There is already a sound_numdecimals() function, according to Git
it's been around since 2005. No need to add another one :).
This reverts commit 92a0ab8789.
Change-Id: I533ebf1763dd7a27346842982493d4550f05ad7c
