- Drop obsolete NAND patch script (it's simpler to use 'dd' directly)
- Remove an outdated comment
- Fix missing 'void' in a function definition
- Reset the poweroff timer when we poke the backlight
Change-Id: I752624386f30ac95f41a731d2b6be837e12275a9
Some audiohw API calls are shared between playback and recording,
eg. frequency settings. Implementing these in the DAC driver won't
work for the M3K, as it uses a separate codec for microphone input.
Change-Id: Ieb0a267f8a81b9e2bbf0bbca951c5778f8dcd203
- Add support for skip and seek while the player is locked.
(Thanks to @bahus for the suggestion)
- Fix touch zones because the down button zone ended up being
a lot smaller than expected due to the touchpad's wonkiness.
Also added a visual display of the touchpad to its debug menu.
- Fixes the pictureflow keymap because it was mostly unusable.
Change-Id: Ic0da4f8df3613ff7828ce1cb940ed9e77ada3281
SPL and UCL-compressed bootloader are now packed into one output,
bootloader.m3k, eliminating the separate SPL build phase.
The Rockbox bootloader now has a recovery menu, accessible by
holding VOL+ when booting, that lets you back up, restore, and
update the bootloader from the device.
Change-Id: I642c6e5fb83587a013ab2fbfd1adab439561ced2
- Removed unnecessary layers of generic code
- Software ECC is gone since we don't need it now (and maybe not ever)
- Removed bounce buffering, so callers must now align buffers
Change-Id: I33fbac9d9d12a4657980b8618c7d62bfa91e2ea0
This only required a minor patch to the usb-designware driver due
to DMA requiring physical addresses -- on the X1000, these differ
from virtual addresses so we have to do the usual conversion.
Both the mass storage and HID drivers work, but there are a few
issues so this can't be considered 100% stable yet.
- Mass storage might not be detected properly on insertion,
and USB has to be replugged before it shows up
- HID driver may occasionally panic or hang the machine
Change-Id: Ia3ce7591d5928ec7cbca7953abfef01bdbd873ef
- Added register names to reduce usage of magic numbers
- Added function to control max charging current, needed for USB
- Corrected comment about axp173, since FiiO M3K has an axp192
Change-Id: I6604ce8d44e5a2ee84061cf042d17ccc4734ac57
Initializing the clocks in the SPL brings Rockbox in line with
how the FiiO M3K's original SPL works. It's likely other X1000
devices do this too.
There was a logic error in the previous setup: the code falsely
assumed that DDR memory would always be running from MPLL, but
it would be switched to APLL by the bootloader. Rockbox would
then try to re-init APLL, albeit with the same parameters. Maybe
this was the cause of the boot hang on some units.
Change-Id: I64064585e491bbdf1e95fe9428c91a9314f2a917
SPL is now designed so core X1000 code is in control of the boot,
under the reasonable assumption that the device boots from flash.
It should not be too hard to adapt to other X1000 ports.
The biggest functional change is that the SPL can now read/write
the flash, under the control of a host computer. The SPL relies
on the boot ROM for USB communication, so the host has to execute
the SPL multiple times following a protocol.
Change-Id: I3ffaa00e4bf191e043c9df0e2e64d15193ff42c9
- Proper error codes are now returned from all functions. These codes will
be used by a host-side flash tool for error reporting.
- nand_erase_block() was replaced by nand_erase_bytes(). The caller can't
know how big an eraseblock is with the current API, so next best thing
is to verify the correct alignment inside the call and reject the erase
if it isn't properly aligned.
- Fixed typo in nandcmd_block_erase() which would cause an SFC error to be
interpreted as success. Yikes.
Change-Id: Id4ac9b44fa7fc2fcb81ff19ba730df78457c0383
