- retry failed commands up to 6 times
- wait at most 5 seconds for the card to go to TRAN state
- wait for the card to be in TRAN state (i.e. not programming) before
disabling SD clocks (remove the workaround in sd_enable() )
should fix lockups reported on fuzev1 under heavy internal storage + µSD use
(playback + database/pictureflow updating)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26291 a1c6a512-1295-4272-9138-f99709370657
Selecting the right card before the transfer will deselect the other one
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26290 a1c6a512-1295-4272-9138-f99709370657
We assume only one bit is set and use clz to find the most significant
set bit, if there's more than one bit set we'll see it in the panic msg
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26285 a1c6a512-1295-4272-9138-f99709370657
A specific poweroff function needs to be used for wake-up to work
Disable RTC in bootloaders for consistency with other Sansas
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26243 a1c6a512-1295-4272-9138-f99709370657
Charge using 150mA current like the OF to charge faster
Edit clipv2 charging curve with 150mA
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26227 a1c6a512-1295-4272-9138-f99709370657
Move code not defined for bootloader under a single preprocessor check
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26219 a1c6a512-1295-4272-9138-f99709370657
GPIO direction needs only to be set at init
both functions are now one liners so make them static inline
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26218 a1c6a512-1295-4272-9138-f99709370657
- forgot a ccu undocumented thing in init
- finish init code (following linux patch)
- enable interrupts
- don't use dynanmic fifo sizing by default
- move to a more static configuration of usb hardware parameters (it might be necessary to move them to config* files later).
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26195 a1c6a512-1295-4272-9138-f99709370657
we still need to convert uncached addresses to physical addresses
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26177 a1c6a512-1295-4272-9138-f99709370657
No need for special address handling, all addresses are equal to their physical address
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26176 a1c6a512-1295-4272-9138-f99709370657
it's only needed if we hotswap the µSD or if we build the fuzev2
scrollwheel code without irq (which we don't do anyway)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26165 a1c6a512-1295-4272-9138-f99709370657
test_disk doesn't freeze anymore when closing the file between writing & reading
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26164 a1c6a512-1295-4272-9138-f99709370657
The list is ordered by priority, put the DMA and SD interrupts at
the top
This seems to fix the random freezes on heavy storage operation like
building database or pictureflow cache
The recently added audio interrupt had a priority higher than SD slot on
as3525v1, give it a lower priority
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26160 a1c6a512-1295-4272-9138-f99709370657
Show all the adc channels in the IO ports debug menu (not for as3525v2
since the channels are different)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26149 a1c6a512-1295-4272-9138-f99709370657
build it on fuzev2 and clipv2 too, it should be the same controller
as3525v1 file is only build for CONFIG_USBOTG == USBOTG_AS3525, no need
to check for it in the .c file
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26142 a1c6a512-1295-4272-9138-f99709370657
Note to self: Next time don't forget to check a AMSv2 build before committing...
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26130 a1c6a512-1295-4272-9138-f99709370657
- Enable end of charge monitoring once, it doesn't need to be disabled
- Acknowledge the first (wrong) end of charge interrupt on charger enable
(this had been broken in r25299)
- Centralize reads to ENRD* registers and cache the results when needed
- on PP it is not needed because reads are atomic, we only check for
end of charge when the charging, and for charger presence when
discharging
as3525v2 (using as3543) specifics
- I got the datasheet today from AMS, thanks to them for being so fast
and not require me to sign tons of papers!
- USB detection now works on as3525v2 using the as3543. Clip+ won't
reboot to OF yet, it needs mkamsboot support first (usbstack disabled)
- Charging should work, the CHARGER register is at a different place, it
is an extended PMU register -> use ascodec_read/write_charger() to
access it
- real interrupts are not used yet for ENRD, we get thousands of
interrupts per second, apparently only limited by the i2c clock.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26116 a1c6a512-1295-4272-9138-f99709370657
