rockbox/firmware/export/config/iriverh10.h

200 lines
5.4 KiB
C
Raw Normal View History

/*
* This config file is for the iriver H10 20Gb
*/
/* For Rolo and boot loader */
#define MODEL_NUMBER 13
Add working dual-boot bootloaders for H10 and Sansa, which allow booting the OF and Rockbox. Rolo also works. Changes made: Combine bootloader/h10.c and bootloader/e200.c into a common bootloader file (bootloader/main-pp.c) to be used by all mi4 based PortalPlayer targets. The file bootloader/main-pp.c is based off the old bootloader/h10.c with some minor changes to allow it to work on the Sansa too. This effectively adds a Sansa bootloader. Define MODEL_NAME string in config-*.h for use in bootloader. Split crt0-pp.S into separate files for bootloader and normal builds. Bootloader code is now in crt0-pp-bl.S while normal build code stays in crt0-pp.S. Improvements to crt0-pp.S and crt0-pp-bl.S (mostly to make it more multiprocessor safe): * Leave space in bootloader at 0xe0-0xeb since scramble writes over there when it creates the mi4 file (don't leave space for iPods since it's not needed and all code in crt0-pp-bl.S needs to fit before the boot_table at 0x100). * Remove unused DEBUG and STUB code from crt0-pp.S. * Make CPU wait for COP to be sleeping when we put the COP to sleep. * Invalidate COP cache when COP wakes * Flush CPU cache before waking COP * Make sure only the CPU clears the BSS (not the COP) * Make sure only the CPU sets up its own stack (not the COP) Rolo works on H10, so enable it. Make Sansa e200 use rockbox.e200 rather than PP5022.mi4 for 'Normal' builds. This makes updating rockbox simpler as we don't need to go through the firmware update procedure, but rather just put a new rockbox.e200 on the device. rockbox.e200 uses a simple 'add' checksum. git-svn-id: svn://svn.rockbox.org/rockbox/trunk@11815 a1c6a512-1295-4272-9138-f99709370657
2006-12-19 11:33:53 +00:00
#define MODEL_NAME "iriver H10 20GB"
/* define this if you use an ATA controller */
#define CONFIG_STORAGE STORAGE_ATA
/*define this if the ATA controller and method of USB access support LBA48 */
#define HAVE_LBA48
/* define this if you have recording possibility */
#define HAVE_RECORDING
/* Define bitmask of input sources - recordable bitmask can be defined
explicitly if different */
#define INPUT_SRC_CAPS (SRC_CAP_MIC | SRC_CAP_LINEIN | SRC_CAP_FMRADIO)
/* define the bitmask of hardware sample rates */
#define HW_SAMPR_CAPS (/*SAMPR_CAP_96 | SAMPR_CAP_88 |*/ SAMPR_CAP_48 | \
SAMPR_CAP_44 | SAMPR_CAP_32 | SAMPR_CAP_8)
/* define the bitmask of recording sample rates */
#define REC_SAMPR_CAPS (/*SAMPR_CAP_96 | SAMPR_CAP_88 |*/ SAMPR_CAP_48 | \
SAMPR_CAP_44 | SAMPR_CAP_32 | SAMPR_CAP_8)
/* define this if you have a colour LCD */
#define HAVE_LCD_COLOR
/* define this if you want album art for this target */
#define HAVE_ALBUMART
/* define this to enable bitmap scaling */
#define HAVE_BMP_SCALING
/* define this to enable JPEG decoding */
#define HAVE_JPEG
/* define this if you have access to the quickscreen */
#define HAVE_QUICKSCREEN
/* define this if you would like tagcache to build on this target */
#define HAVE_TAGCACHE
/* LCD dimensions */
#define LCD_WIDTH 160
#define LCD_HEIGHT 128
/* sqrt(160^2 + 128^2) / 1.5 = 136.6 */
#define LCD_DPI 137
#define LCD_DEPTH 16 /* 65536 colours */
#define LCD_PIXELFORMAT RGB565SWAPPED /* rgb565 byte-swapped */
#ifndef BOOTLOADER
/* Define this if your LCD can be enabled/disabled */
#define HAVE_LCD_ENABLE
/* Define this if your LCD can be put to sleep. HAVE_LCD_ENABLE
* should be defined as well.
* We can currently put the lcd to sleep but it won't wake up properly */
#define HAVE_LCD_SLEEP
#define HAVE_LCD_SLEEP_SETTING
#endif
/* define this if you can flip your LCD */
#define HAVE_LCD_FLIP
/* define this if you can invert the colours on your LCD */
#define HAVE_LCD_INVERT
/* #define IRAM_LCDFRAMEBUFFER IDATA_ATTR *//* put the lcd frame buffer in IRAM */
#define CONFIG_KEYPAD IRIVER_H10_PAD
/* Define this to enable morse code input */
#define HAVE_MORSE_INPUT
/* define this if you have a real-time clock */
#ifndef BOOTLOADER
#define CONFIG_RTC RTC_E8564
#define HAVE_RTC_ALARM
#endif
/* define this if you have a disk storage, i.e. something
that needs spinups and can cause skips when shaked */
#define HAVE_DISK_STORAGE
/* Define this if you have a software controlled poweroff */
#define HAVE_SW_POWEROFF
/* The number of bytes reserved for loadable codecs */
#define CODEC_SIZE 0x100000
/* The number of bytes reserved for loadable plugins */
#define PLUGIN_BUFFER_SIZE 0x80000
/* Define this if you have the WM8731 audio codec */
#define HAVE_WM8731
/* WM8731 has no tone controls, so we use the software ones */
#define HAVE_SW_TONE_CONTROLS
#define AB_REPEAT_ENABLE
/* FM Tuner */
#define CONFIG_TUNER TEA5767
#define CONFIG_TUNER_XTAL 32768
/* Define this for LCD backlight available */
#define HAVE_BACKLIGHT
#define AB_REPEAT_ENABLE
#define BATTERY_CAPACITY_DEFAULT 1550 /* default battery capacity */
#define BATTERY_CAPACITY_MIN 1500 /* min. capacity selectable */
#define BATTERY_CAPACITY_MAX 3200 /* max. capacity selectable */
#define BATTERY_CAPACITY_INC 50 /* capacity increment */
#define BATTERY_TYPES_COUNT 1 /* only one type */
#define CONFIG_BATTERY_MEASURE VOLTAGE_MEASURE
/* Hardware controlled charging */
#define CONFIG_CHARGING CHARGING_SIMPLE
/* define this if the unit can be powered or charged via USB */
#define HAVE_USB_POWER
/* Define this if you have a PortalPlayer PP5020 */
#define CONFIG_CPU PP5020
/* Define this if you want to use the PP5020 i2c interface */
#define CONFIG_I2C I2C_PP5020
/* define this if the hardware can be powered off while charging */
#define HAVE_POWEROFF_WHILE_CHARGING
/* The start address index for ROM builds */
#define ROM_START 0x00000000
/* The size of the flash ROM */
#define FLASH_SIZE 0x100000
/* Define this to the CPU frequency */
#define CPU_FREQ 75000000
/* Type of LCD */
#define CONFIG_LCD LCD_H10_20GB
/* Define this if your LCD can set contrast */
#define HAVE_LCD_CONTRAST
#define MIN_CONTRAST_SETTING 0
#define MAX_CONTRAST_SETTING 30
#define DEFAULT_CONTRAST_SETTING 14 /* Match boot contrast */
/* We're able to shut off power to the HDD */
#define HAVE_ATA_POWER_OFF
/* Offset ( in the firmware file's header ) to the file CRC and data. These are
only used when loading the old format rockbox.h10 file */
#define FIRMWARE_OFFSET_FILE_CRC 0x0
#define FIRMWARE_OFFSET_FILE_DATA 0x8
/* USB On-the-go */
#define CONFIG_USBOTG USBOTG_ARC
/* enable these for the experimental usb stack */
#define HAVE_USBSTACK
#define USB_VENDOR_ID 0x0B70
#define USB_PRODUCT_ID 0x00BA
#define HAVE_USB_HID_MOUSE
#ifdef BOOTLOADER
#define HAVE_BOOTLOADER_USB_MODE
#endif
/* Define this if you have adjustable CPU frequency */
#define HAVE_ADJUSTABLE_CPU_FREQ
#define MI4_FORMAT
#define BOOTFILE_EXT "mi4"
#define BOOTFILE "rockbox." BOOTFILE_EXT
#define BOOTDIR "/.rockbox"
#define ICODE_ATTR_TREMOR_NOT_MDCT
/* DMA is used only for reading on PP502x because although reads are ~8x faster
* writes appear to be ~25% slower.
*/
#ifndef BOOTLOADER
#define HAVE_ATA_DMA
#endif
/* Define this if a programmable hotkey is mapped */
#define HAVE_HOTKEY