ec8f328d89
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@7760 a1c6a512-1295-4272-9138-f99709370657
1210 lines
30 KiB
C
1210 lines
30 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2005 by Richard S. La Charité III
|
|
*
|
|
* All files in this archive are subject to the GNU General Public License.
|
|
* See the file COPYING in the source tree root for full license agreement.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#include "config.h"
|
|
#include "cpu.h"
|
|
#include "lcd.h"
|
|
#include "lcd-remote.h"
|
|
#include "kernel.h"
|
|
#include "thread.h"
|
|
#include <string.h>
|
|
#include <stdlib.h>
|
|
#include "file.h"
|
|
#include "debug.h"
|
|
#include "system.h"
|
|
#include "font.h"
|
|
|
|
/*** definitions ***/
|
|
|
|
#define LCD_REMOTE_CNTL_ADC_NORMAL 0xa0
|
|
#define LCD_REMOTE_CNTL_ADC_REVERSE 0xa1
|
|
#define LCD_REMOTE_CNTL_SHL_NORMAL 0xc0
|
|
#define LCD_REMOTE_CNTL_SHL_REVERSE 0xc8
|
|
#define LCD_REMOTE_CNTL_DISPLAY_ON_OFF 0xae
|
|
#define LCD_REMOTE_CNTL_ENTIRE_ON_OFF 0xa4
|
|
#define LCD_REMOTE_CNTL_REVERSE_ON_OFF 0xa6
|
|
#define LCD_REMOTE_CNTL_NOP 0xe3
|
|
#define LCD_REMOTE_CNTL_POWER_CONTROL 0x2b
|
|
#define LCD_REMOTE_CNTL_SELECT_REGULATOR 0x20
|
|
#define LCD_REMOTE_CNTL_SELECT_BIAS 0xa2
|
|
#define LCD_REMOTE_CNTL_SELECT_VOLTAGE 0x81
|
|
#define LCD_REMOTE_CNTL_INIT_LINE 0x40
|
|
#define LCD_REMOTE_CNTL_SET_PAGE_ADDRESS 0xB0
|
|
|
|
#define LCD_REMOTE_CNTL_HIGHCOL 0x10 /* Upper column address */
|
|
#define LCD_REMOTE_CNTL_LOWCOL 0x00 /* Lower column address */
|
|
|
|
#define CS_LO and_l(~0x00000004, &GPIO1_OUT)
|
|
#define CS_HI or_l(0x00000004, &GPIO1_OUT)
|
|
#define CLK_LO and_l(~0x10000000, &GPIO_OUT)
|
|
#define CLK_HI or_l(0x10000000, &GPIO_OUT)
|
|
#define DATA_LO and_l(~0x00040000, &GPIO1_OUT)
|
|
#define DATA_HI or_l(0x00040000, &GPIO1_OUT)
|
|
#define RS_LO and_l(~0x00010000, &GPIO_OUT)
|
|
#define RS_HI or_l(0x00010000, &GPIO_OUT)
|
|
|
|
/* delay loop */
|
|
#define DELAY do { int _x; for(_x=0;_x<3;_x++);} while (0)
|
|
|
|
#define SCROLLABLE_LINES 13
|
|
|
|
/*** globals ***/
|
|
|
|
unsigned char lcd_remote_framebuffer[LCD_REMOTE_HEIGHT/8][LCD_REMOTE_WIDTH]
|
|
IBSS_ATTR;
|
|
|
|
static int drawmode = DRMODE_SOLID;
|
|
static int xmargin = 0;
|
|
static int ymargin = 0;
|
|
static int curfont = FONT_SYSFIXED;
|
|
#ifndef SIMULATOR
|
|
static int xoffset; /* needed for flip */
|
|
|
|
/* remote hotplug */
|
|
static int countdown; /* for remote plugging debounce */
|
|
static bool last_remote_status = false;
|
|
static bool init_remote = false; /* scroll thread should init lcd */
|
|
static bool remote_initialized = false;
|
|
/* cached settings values */
|
|
static bool cached_invert = false;
|
|
static bool cached_flip = false;
|
|
static int cached_contrast = 32;
|
|
static int cached_roll = 0;
|
|
#endif
|
|
|
|
/* scrolling */
|
|
static volatile int scrolling_lines=0; /* Bitpattern of which lines are scrolling */
|
|
static void scroll_thread(void);
|
|
static long scroll_stack[DEFAULT_STACK_SIZE/sizeof(long)];
|
|
static const char scroll_name[] = "remote_scroll";
|
|
static int scroll_ticks = 12; /* # of ticks between updates*/
|
|
static int scroll_delay = HZ/2; /* ticks delay before start */
|
|
static int scroll_step = 6; /* pixels per scroll step */
|
|
static int bidir_limit = 50; /* percent */
|
|
static struct scrollinfo scroll[SCROLLABLE_LINES];
|
|
|
|
static const char scroll_tick_table[16] = {
|
|
/* Hz values:
|
|
1, 1.25, 1.55, 2, 2.5, 3.12, 4, 5, 6.25, 8.33, 10, 12.5, 16.7, 20, 25, 33 */
|
|
100, 80, 64, 50, 40, 32, 25, 20, 16, 12, 10, 8, 6, 5, 4, 3
|
|
};
|
|
|
|
/*** driver routines ***/
|
|
|
|
#ifndef SIMULATOR
|
|
void lcd_remote_backlight_on(void)
|
|
{
|
|
and_l(~0x00000800, &GPIO_OUT);
|
|
}
|
|
|
|
void lcd_remote_backlight_off(void)
|
|
{
|
|
or_l(0x00000800, &GPIO_OUT);
|
|
}
|
|
|
|
void lcd_remote_write_command(int cmd)
|
|
{
|
|
int i;
|
|
|
|
RS_LO;
|
|
CS_LO;
|
|
|
|
for (i = 0; i < 8; i++)
|
|
{
|
|
if (cmd & 0x80)
|
|
DATA_HI;
|
|
else
|
|
DATA_LO;
|
|
|
|
CLK_HI;
|
|
cmd <<= 1;
|
|
DELAY;
|
|
|
|
CLK_LO;
|
|
}
|
|
|
|
CS_HI;
|
|
}
|
|
|
|
void lcd_remote_write_data(const unsigned char* p_bytes, int count)
|
|
{
|
|
int i, j;
|
|
int data;
|
|
|
|
RS_HI;
|
|
CS_LO;
|
|
|
|
for (i = 0; i < count; i++)
|
|
{
|
|
data = p_bytes[i];
|
|
|
|
for (j = 0; j < 8; j++)
|
|
{
|
|
if (data & 0x80)
|
|
DATA_HI;
|
|
else
|
|
DATA_LO;
|
|
|
|
CLK_HI;
|
|
data <<= 1;
|
|
DELAY;
|
|
|
|
CLK_LO;
|
|
}
|
|
}
|
|
|
|
CS_HI;
|
|
}
|
|
|
|
void lcd_remote_write_command_ex(int cmd, int data)
|
|
{
|
|
int i;
|
|
|
|
CS_LO;
|
|
RS_LO;
|
|
|
|
for (i = 0; i < 8; i++)
|
|
{
|
|
if (cmd & 0x80)
|
|
DATA_HI;
|
|
else
|
|
DATA_LO;
|
|
|
|
CLK_HI;
|
|
cmd <<= 1;
|
|
DELAY;
|
|
|
|
CLK_LO;
|
|
}
|
|
|
|
for (i = 0; i < 8; i++)
|
|
{
|
|
if (data & 0x80)
|
|
DATA_HI;
|
|
else
|
|
DATA_LO;
|
|
|
|
CLK_HI;
|
|
data <<= 1;
|
|
DELAY;
|
|
|
|
CLK_LO;
|
|
}
|
|
|
|
CS_HI;
|
|
}
|
|
#endif /* !SIMULATOR */
|
|
|
|
/*** hardware configuration ***/
|
|
|
|
int lcd_remote_default_contrast(void)
|
|
{
|
|
return 32;
|
|
}
|
|
|
|
#ifndef SIMULATOR
|
|
|
|
void lcd_remote_powersave(bool on)
|
|
{
|
|
if (remote_initialized)
|
|
{
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_DISPLAY_ON_OFF | (on ? 0 : 1));
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_ENTIRE_ON_OFF | (on ? 1 : 0));
|
|
}
|
|
}
|
|
|
|
void lcd_remote_set_contrast(int val)
|
|
{
|
|
cached_contrast = val;
|
|
if (remote_initialized)
|
|
lcd_remote_write_command_ex(LCD_REMOTE_CNTL_SELECT_VOLTAGE, val);
|
|
}
|
|
|
|
void lcd_remote_set_invert_display(bool yesno)
|
|
{
|
|
cached_invert = yesno;
|
|
if (remote_initialized)
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_REVERSE_ON_OFF | (yesno?1:0));
|
|
}
|
|
|
|
/* turn the display upside down (call lcd_remote_update() afterwards) */
|
|
void lcd_remote_set_flip(bool yesno)
|
|
{
|
|
cached_flip = yesno;
|
|
if (yesno)
|
|
{
|
|
xoffset = 0;
|
|
if (remote_initialized)
|
|
{
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_ADC_NORMAL);
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_SHL_NORMAL);
|
|
}
|
|
}
|
|
else
|
|
{
|
|
xoffset = 132 - LCD_REMOTE_WIDTH;
|
|
if (remote_initialized)
|
|
{
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_ADC_REVERSE);
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_SHL_REVERSE);
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Rolls up the lcd display by the specified amount of lines.
|
|
* Lines that are rolled out over the top of the screen are
|
|
* rolled in from the bottom again. This is a hardware
|
|
* remapping only and all operations on the lcd are affected.
|
|
* ->
|
|
* @param int lines - The number of lines that are rolled.
|
|
* The value must be 0 <= pixels < LCD_REMOTE_HEIGHT. */
|
|
void lcd_remote_roll(int lines)
|
|
{
|
|
char data[2];
|
|
|
|
cached_roll = lines;
|
|
|
|
if (remote_initialized)
|
|
{
|
|
lines &= LCD_REMOTE_HEIGHT-1;
|
|
data[0] = lines & 0xff;
|
|
data[1] = lines >> 8;
|
|
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_INIT_LINE | 0x0); // init line
|
|
lcd_remote_write_data(data, 2);
|
|
}
|
|
}
|
|
|
|
/* The actual LCD init */
|
|
static void remote_lcd_init(void)
|
|
{
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_SELECT_BIAS | 0x0);
|
|
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_POWER_CONTROL | 0x5);
|
|
sleep(1);
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_POWER_CONTROL | 0x6);
|
|
sleep(1);
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_POWER_CONTROL | 0x7);
|
|
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_SELECT_REGULATOR | 0x4); // 0x4 Select regulator @ 5.0 (default);
|
|
|
|
sleep(1);
|
|
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_INIT_LINE | 0x0); // init line
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_SET_PAGE_ADDRESS | 0x0); // page address
|
|
lcd_remote_write_command_ex(0x10, 0x00); // Column MSB + LSB
|
|
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_DISPLAY_ON_OFF | 1);
|
|
|
|
remote_initialized = true;
|
|
|
|
lcd_remote_set_flip(cached_flip);
|
|
lcd_remote_set_contrast(cached_contrast);
|
|
lcd_remote_set_invert_display(cached_invert);
|
|
lcd_remote_roll(cached_roll);
|
|
}
|
|
|
|
/* Monitor remote hotswap */
|
|
static void remote_tick(void)
|
|
{
|
|
bool current_status;
|
|
|
|
current_status = ((GPIO_READ & 0x40000000) == 0);
|
|
/* Only report when the status has changed */
|
|
if (current_status != last_remote_status)
|
|
{
|
|
last_remote_status = current_status;
|
|
countdown = current_status ? HZ : 1;
|
|
}
|
|
else
|
|
{
|
|
/* Count down until it gets negative */
|
|
if (countdown >= 0)
|
|
countdown--;
|
|
|
|
if (countdown == 0)
|
|
{
|
|
if (current_status)
|
|
{
|
|
init_remote = true;
|
|
/* request init in scroll_thread */
|
|
}
|
|
else
|
|
{
|
|
CLK_LO;
|
|
CS_HI;
|
|
remote_initialized = false;
|
|
}
|
|
}
|
|
}
|
|
}
|
|
#endif /* !SIMULATOR */
|
|
|
|
/* LCD init */
|
|
#ifdef SIMULATOR
|
|
|
|
void lcd_remote_init(void)
|
|
{
|
|
create_thread(scroll_thread, scroll_stack,
|
|
sizeof(scroll_stack), scroll_name);
|
|
}
|
|
#else /* !SIMULATOR */
|
|
|
|
/* Initialise ports and kick off monitor */
|
|
void lcd_remote_init(void)
|
|
{
|
|
or_l(0x10010800, &GPIO_FUNCTION); /* GPIO11: Backlight
|
|
GPIO16: RS
|
|
GPIO28: CLK */
|
|
|
|
or_l(0x00040004, &GPIO1_FUNCTION); /* GPIO34: CS
|
|
GPIO50: Data */
|
|
or_l(0x10010800, &GPIO_ENABLE);
|
|
or_l(0x00040004, &GPIO1_ENABLE);
|
|
|
|
lcd_remote_clear_display();
|
|
|
|
tick_add_task(remote_tick);
|
|
create_thread(scroll_thread, scroll_stack,
|
|
sizeof(scroll_stack), scroll_name);
|
|
}
|
|
|
|
/*** update functions ***/
|
|
|
|
/* Update the display.
|
|
This must be called after all other LCD functions that change the display. */
|
|
void lcd_remote_update(void) ICODE_ATTR;
|
|
void lcd_remote_update(void)
|
|
{
|
|
int y;
|
|
|
|
if (!remote_initialized)
|
|
return;
|
|
|
|
/* Copy display bitmap to hardware */
|
|
for (y = 0; y < LCD_REMOTE_HEIGHT/8; y++)
|
|
{
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_SET_PAGE_ADDRESS | y);
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_HIGHCOL | ((xoffset >> 4) & 0xf));
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_LOWCOL | (xoffset & 0xf));
|
|
lcd_remote_write_data(lcd_remote_framebuffer[y], LCD_REMOTE_WIDTH);
|
|
}
|
|
}
|
|
|
|
/* Update a fraction of the display. */
|
|
void lcd_remote_update_rect(int, int, int, int) ICODE_ATTR;
|
|
void lcd_remote_update_rect(int x, int y, int width, int height)
|
|
{
|
|
int ymax;
|
|
|
|
if (!remote_initialized)
|
|
return;
|
|
|
|
/* The Y coordinates have to work on even 8 pixel rows */
|
|
ymax = (y + height-1) >> 3;
|
|
y >>= 3;
|
|
|
|
if(x + width > LCD_REMOTE_WIDTH)
|
|
width = LCD_REMOTE_WIDTH - x;
|
|
if (width <= 0)
|
|
return; /* nothing left to do, 0 is harmful to lcd_write_data() */
|
|
if(ymax >= LCD_REMOTE_HEIGHT/8)
|
|
ymax = LCD_REMOTE_HEIGHT/8-1;
|
|
|
|
/* Copy specified rectange bitmap to hardware */
|
|
for (; y <= ymax; y++)
|
|
{
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_SET_PAGE_ADDRESS | y);
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_HIGHCOL | (((x+xoffset) >> 4) & 0xf));
|
|
lcd_remote_write_command(LCD_REMOTE_CNTL_LOWCOL | ((x+xoffset) & 0xf));
|
|
lcd_remote_write_data(&lcd_remote_framebuffer[y][x], width);
|
|
}
|
|
}
|
|
#endif /* !SIMULATOR */
|
|
|
|
/*** parameter handling ***/
|
|
|
|
void lcd_remote_set_drawmode(int mode)
|
|
{
|
|
drawmode = mode & (DRMODE_SOLID|DRMODE_INVERSEVID);
|
|
}
|
|
|
|
int lcd_remote_get_drawmode(void)
|
|
{
|
|
return drawmode;
|
|
}
|
|
|
|
void lcd_remote_setmargins(int x, int y)
|
|
{
|
|
xmargin = x;
|
|
ymargin = y;
|
|
}
|
|
|
|
int lcd_remote_getxmargin(void)
|
|
{
|
|
return xmargin;
|
|
}
|
|
|
|
int lcd_remote_getymargin(void)
|
|
{
|
|
return ymargin;
|
|
}
|
|
|
|
|
|
void lcd_remote_setfont(int newfont)
|
|
{
|
|
curfont = newfont;
|
|
}
|
|
|
|
int lcd_remote_getstringsize(const unsigned char *str, int *w, int *h)
|
|
{
|
|
return font_getstringsize(str, w, h, curfont);
|
|
}
|
|
|
|
/*** low-level drawing functions ***/
|
|
|
|
static void setpixel(int x, int y)
|
|
{
|
|
lcd_remote_framebuffer[y>>3][x] |= 1 << (y & 7);
|
|
}
|
|
|
|
static void clearpixel(int x, int y)
|
|
{
|
|
lcd_remote_framebuffer[y>>3][x] &= ~(1 << (y & 7));
|
|
}
|
|
|
|
static void flippixel(int x, int y)
|
|
{
|
|
lcd_remote_framebuffer[y>>3][x] ^= 1 << (y & 7);
|
|
}
|
|
|
|
static void nopixel(int x, int y)
|
|
{
|
|
(void)x;
|
|
(void)y;
|
|
}
|
|
|
|
lcd_pixelfunc_type* lcd_remote_pixelfuncs[8] = {
|
|
flippixel, nopixel, setpixel, setpixel,
|
|
nopixel, clearpixel, nopixel, clearpixel
|
|
};
|
|
|
|
static void flipblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void flipblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address ^= bits & mask;
|
|
}
|
|
|
|
static void bgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void bgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address &= bits | ~mask;
|
|
}
|
|
|
|
static void fgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void fgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address |= bits & mask;
|
|
}
|
|
|
|
static void solidblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void solidblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address = (*address & ~mask) | (bits & mask);
|
|
}
|
|
|
|
static void flipinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void flipinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address ^= ~bits & mask;
|
|
}
|
|
|
|
static void bginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void bginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address &= ~(bits & mask);
|
|
}
|
|
|
|
static void fginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void fginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address |= ~bits & mask;
|
|
}
|
|
|
|
static void solidinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void solidinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address = (*address & ~mask) | (~bits & mask);
|
|
}
|
|
|
|
lcd_blockfunc_type* lcd_remote_blockfuncs[8] = {
|
|
flipblock, bgblock, fgblock, solidblock,
|
|
flipinvblock, bginvblock, fginvblock, solidinvblock
|
|
};
|
|
|
|
/*** drawing functions ***/
|
|
|
|
/* Clear the whole display */
|
|
void lcd_remote_clear_display(void)
|
|
{
|
|
unsigned bits = (drawmode & DRMODE_INVERSEVID) ? 0xFFu : 0;
|
|
|
|
memset(lcd_remote_framebuffer, bits, sizeof lcd_remote_framebuffer);
|
|
scrolling_lines = 0;
|
|
}
|
|
|
|
/* Set a single pixel */
|
|
void lcd_remote_drawpixel(int x, int y)
|
|
{
|
|
if (((unsigned)x < LCD_REMOTE_WIDTH) && ((unsigned)y < LCD_REMOTE_HEIGHT))
|
|
lcd_remote_pixelfuncs[drawmode](x, y);
|
|
}
|
|
|
|
/* Draw a line */
|
|
void lcd_remote_drawline(int x1, int y1, int x2, int y2)
|
|
{
|
|
int numpixels;
|
|
int i;
|
|
int deltax, deltay;
|
|
int d, dinc1, dinc2;
|
|
int x, xinc1, xinc2;
|
|
int y, yinc1, yinc2;
|
|
lcd_pixelfunc_type *pfunc = lcd_remote_pixelfuncs[drawmode];
|
|
|
|
deltax = abs(x2 - x1);
|
|
deltay = abs(y2 - y1);
|
|
xinc2 = 1;
|
|
yinc2 = 1;
|
|
|
|
if (deltax >= deltay)
|
|
{
|
|
numpixels = deltax;
|
|
d = 2 * deltay - deltax;
|
|
dinc1 = deltay * 2;
|
|
dinc2 = (deltay - deltax) * 2;
|
|
xinc1 = 1;
|
|
yinc1 = 0;
|
|
}
|
|
else
|
|
{
|
|
numpixels = deltay;
|
|
d = 2 * deltax - deltay;
|
|
dinc1 = deltax * 2;
|
|
dinc2 = (deltax - deltay) * 2;
|
|
xinc1 = 0;
|
|
yinc1 = 1;
|
|
}
|
|
numpixels++; /* include endpoints */
|
|
|
|
if (x1 > x2)
|
|
{
|
|
xinc1 = -xinc1;
|
|
xinc2 = -xinc2;
|
|
}
|
|
|
|
if (y1 > y2)
|
|
{
|
|
yinc1 = -yinc1;
|
|
yinc2 = -yinc2;
|
|
}
|
|
|
|
x = x1;
|
|
y = y1;
|
|
|
|
for (i = 0; i < numpixels; i++)
|
|
{
|
|
if (((unsigned)x < LCD_REMOTE_WIDTH) && ((unsigned)y < LCD_REMOTE_HEIGHT))
|
|
pfunc(x, y);
|
|
|
|
if (d < 0)
|
|
{
|
|
d += dinc1;
|
|
x += xinc1;
|
|
y += yinc1;
|
|
}
|
|
else
|
|
{
|
|
d += dinc2;
|
|
x += xinc2;
|
|
y += yinc2;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Draw a horizontal line (optimised) */
|
|
void lcd_remote_hline(int x1, int x2, int y)
|
|
{
|
|
int x;
|
|
unsigned char *dst, *dst_end;
|
|
unsigned mask;
|
|
lcd_blockfunc_type *bfunc;
|
|
|
|
/* direction flip */
|
|
if (x2 < x1)
|
|
{
|
|
x = x1;
|
|
x1 = x2;
|
|
x2 = x;
|
|
}
|
|
|
|
/* nothing to draw? */
|
|
if (((unsigned)y >= LCD_REMOTE_HEIGHT) || (x1 >= LCD_REMOTE_WIDTH)
|
|
|| (x2 < 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (x1 < 0)
|
|
x1 = 0;
|
|
if (x2 >= LCD_REMOTE_WIDTH)
|
|
x2 = LCD_REMOTE_WIDTH-1;
|
|
|
|
bfunc = lcd_remote_blockfuncs[drawmode];
|
|
dst = &lcd_remote_framebuffer[y>>3][x1];
|
|
mask = 1 << (y & 7);
|
|
|
|
dst_end = dst + x2 - x1;
|
|
do
|
|
bfunc(dst++, mask, 0xFFu);
|
|
while (dst <= dst_end);
|
|
}
|
|
|
|
/* Draw a vertical line (optimised) */
|
|
void lcd_remote_vline(int x, int y1, int y2)
|
|
{
|
|
int ny;
|
|
unsigned char *dst;
|
|
unsigned mask, mask_bottom;
|
|
lcd_blockfunc_type *bfunc;
|
|
|
|
/* direction flip */
|
|
if (y2 < y1)
|
|
{
|
|
ny = y1;
|
|
y1 = y2;
|
|
y2 = ny;
|
|
}
|
|
|
|
/* nothing to draw? */
|
|
if (((unsigned)x >= LCD_REMOTE_WIDTH) || (y1 >= LCD_REMOTE_HEIGHT)
|
|
|| (y2 < 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (y1 < 0)
|
|
y1 = 0;
|
|
if (y2 >= LCD_REMOTE_HEIGHT)
|
|
y2 = LCD_REMOTE_HEIGHT-1;
|
|
|
|
bfunc = lcd_remote_blockfuncs[drawmode];
|
|
dst = &lcd_remote_framebuffer[y1>>3][x];
|
|
ny = y2 - (y1 & ~7);
|
|
mask = 0xFFu << (y1 & 7);
|
|
mask_bottom = 0xFFu >> (~ny & 7);
|
|
|
|
for (; ny >= 8; ny -= 8)
|
|
{
|
|
bfunc(dst, mask, 0xFFu);
|
|
dst += LCD_REMOTE_WIDTH;
|
|
mask = 0xFFu;
|
|
}
|
|
mask &= mask_bottom;
|
|
bfunc(dst, mask, 0xFFu);
|
|
}
|
|
|
|
/* Draw a rectangular box */
|
|
void lcd_remote_drawrect(int x, int y, int width, int height)
|
|
{
|
|
if ((width <= 0) || (height <= 0))
|
|
return;
|
|
|
|
int x2 = x + width - 1;
|
|
int y2 = y + height - 1;
|
|
|
|
lcd_remote_vline(x, y, y2);
|
|
lcd_remote_vline(x2, y, y2);
|
|
lcd_remote_hline(x, x2, y);
|
|
lcd_remote_hline(x, x2, y2);
|
|
}
|
|
|
|
/* Fill a rectangular area */
|
|
void lcd_remote_fillrect(int x, int y, int width, int height)
|
|
{
|
|
int ny;
|
|
unsigned char *dst, *dst_end;
|
|
unsigned mask, mask_bottom;
|
|
unsigned bits = 0xFFu;
|
|
lcd_blockfunc_type *bfunc;
|
|
bool fillopt;
|
|
|
|
/* nothing to draw? */
|
|
if ((width <= 0) || (height <= 0) || (x >= LCD_REMOTE_WIDTH)
|
|
|| (y >= LCD_REMOTE_HEIGHT) || (x + width <= 0) || (y + height <= 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (x < 0)
|
|
{
|
|
width += x;
|
|
x = 0;
|
|
}
|
|
if (y < 0)
|
|
{
|
|
height += y;
|
|
y = 0;
|
|
}
|
|
if (x + width > LCD_REMOTE_WIDTH)
|
|
width = LCD_REMOTE_WIDTH - x;
|
|
if (y + height > LCD_REMOTE_HEIGHT)
|
|
height = LCD_REMOTE_HEIGHT - y;
|
|
|
|
fillopt = (drawmode & DRMODE_INVERSEVID) ?
|
|
(drawmode & DRMODE_BG) : (drawmode & DRMODE_FG);
|
|
if (fillopt &&(drawmode & DRMODE_INVERSEVID))
|
|
bits = 0;
|
|
bfunc = lcd_remote_blockfuncs[drawmode];
|
|
dst = &lcd_remote_framebuffer[y>>3][x];
|
|
ny = height - 1 + (y & 7);
|
|
mask = 0xFFu << (y & 7);
|
|
mask_bottom = 0xFFu >> (~ny & 7);
|
|
|
|
for (; ny >= 8; ny -= 8)
|
|
{
|
|
if (fillopt && (mask == 0xFFu))
|
|
memset(dst, bits, width);
|
|
else
|
|
{
|
|
unsigned char *dst_row = dst;
|
|
|
|
dst_end = dst_row + width;
|
|
do
|
|
bfunc(dst_row++, mask, 0xFFu);
|
|
while (dst_row < dst_end);
|
|
}
|
|
|
|
dst += LCD_REMOTE_WIDTH;
|
|
mask = 0xFFu;
|
|
}
|
|
mask &= mask_bottom;
|
|
|
|
if (fillopt && (mask == 0xFFu))
|
|
memset(dst, bits, width);
|
|
else
|
|
{
|
|
dst_end = dst + width;
|
|
do
|
|
bfunc(dst++, mask, 0xFFu);
|
|
while (dst < dst_end);
|
|
}
|
|
}
|
|
|
|
/* About Rockbox' internal bitmap format:
|
|
*
|
|
* A bitmap contains one bit for every pixel that defines if that pixel is
|
|
* black (1) or white (0). Bits within a byte are arranged vertically, LSB
|
|
* at top.
|
|
* The bytes are stored in row-major order, with byte 0 being top left,
|
|
* byte 1 2nd from left etc. The first row of bytes defines pixel rows
|
|
* 0..7, the second row defines pixel row 8..15 etc.
|
|
*
|
|
* This is the same as the internal lcd hw format. */
|
|
|
|
/* Draw a partial bitmap */
|
|
void lcd_remote_bitmap_part(const unsigned char *src, int src_x, int src_y,
|
|
int stride, int x, int y, int width, int height)
|
|
ICODE_ATTR;
|
|
void lcd_remote_bitmap_part(const unsigned char *src, int src_x, int src_y,
|
|
int stride, int x, int y, int width, int height)
|
|
{
|
|
int shift, ny;
|
|
unsigned char *dst, *dst_end;
|
|
unsigned mask, mask_bottom;
|
|
lcd_blockfunc_type *bfunc;
|
|
|
|
/* nothing to draw? */
|
|
if ((width <= 0) || (height <= 0) || (x >= LCD_REMOTE_WIDTH)
|
|
|| (y >= LCD_REMOTE_HEIGHT) || (x + width <= 0) || (y + height <= 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (x < 0)
|
|
{
|
|
width += x;
|
|
src_x -= x;
|
|
x = 0;
|
|
}
|
|
if (y < 0)
|
|
{
|
|
height += y;
|
|
src_y -= y;
|
|
y = 0;
|
|
}
|
|
if (x + width > LCD_REMOTE_WIDTH)
|
|
width = LCD_REMOTE_WIDTH - x;
|
|
if (y + height > LCD_REMOTE_HEIGHT)
|
|
height = LCD_REMOTE_HEIGHT - y;
|
|
|
|
src += stride * (src_y >> 3) + src_x; /* move starting point */
|
|
src_y &= 7;
|
|
y -= src_y;
|
|
dst = &lcd_remote_framebuffer[y>>3][x];
|
|
shift = y & 7;
|
|
ny = height - 1 + shift + src_y;
|
|
|
|
bfunc = lcd_remote_blockfuncs[drawmode];
|
|
mask = 0xFFu << (shift + src_y);
|
|
mask_bottom = 0xFFu >> (~ny & 7);
|
|
|
|
if (shift == 0)
|
|
{
|
|
bool copyopt = (drawmode == DRMODE_SOLID);
|
|
|
|
for (; ny >= 8; ny -= 8)
|
|
{
|
|
if (copyopt && (mask == 0xFFu))
|
|
memcpy(dst, src, width);
|
|
else
|
|
{
|
|
const unsigned char *src_row = src;
|
|
unsigned char *dst_row = dst;
|
|
|
|
dst_end = dst_row + width;
|
|
do
|
|
bfunc(dst_row++, mask, *src_row++);
|
|
while (dst_row < dst_end);
|
|
}
|
|
|
|
src += stride;
|
|
dst += LCD_REMOTE_WIDTH;
|
|
mask = 0xFFu;
|
|
}
|
|
mask &= mask_bottom;
|
|
|
|
if (copyopt && (mask == 0xFFu))
|
|
memcpy(dst, src, width);
|
|
else
|
|
{
|
|
dst_end = dst + width;
|
|
do
|
|
bfunc(dst++, mask, *src++);
|
|
while (dst < dst_end);
|
|
}
|
|
}
|
|
else
|
|
{
|
|
dst_end = dst + width;
|
|
do
|
|
{
|
|
const unsigned char *src_col = src++;
|
|
unsigned char *dst_col = dst++;
|
|
unsigned mask_col = mask;
|
|
unsigned data = 0;
|
|
|
|
for (y = ny; y >= 8; y -= 8)
|
|
{
|
|
data |= *src_col << shift;
|
|
|
|
if (mask_col & 0xFFu)
|
|
{
|
|
bfunc(dst_col, mask_col, data);
|
|
mask_col = 0xFFu;
|
|
}
|
|
else
|
|
mask_col >>= 8;
|
|
|
|
src_col += stride;
|
|
dst_col += LCD_REMOTE_WIDTH;
|
|
data >>= 8;
|
|
}
|
|
data |= *src_col << shift;
|
|
bfunc(dst_col, mask_col & mask_bottom, data);
|
|
}
|
|
while (dst < dst_end);
|
|
}
|
|
}
|
|
|
|
/* Draw a full bitmap */
|
|
void lcd_remote_bitmap(const unsigned char *src, int x, int y, int width,
|
|
int height)
|
|
{
|
|
lcd_remote_bitmap_part(src, 0, 0, width, x, y, width, height);
|
|
}
|
|
|
|
/* put a string at a given pixel position, skipping first ofs pixel columns */
|
|
static void lcd_remote_putsxyofs(int x, int y, int ofs, const unsigned char *str)
|
|
{
|
|
int ch;
|
|
struct font* pf = font_get(curfont);
|
|
|
|
while ((ch = *str++) != '\0' && x < LCD_REMOTE_WIDTH)
|
|
{
|
|
int width;
|
|
const unsigned char *bits;
|
|
|
|
/* check input range */
|
|
if (ch < pf->firstchar || ch >= pf->firstchar+pf->size)
|
|
ch = pf->defaultchar;
|
|
ch -= pf->firstchar;
|
|
|
|
/* get proportional width and glyph bits */
|
|
width = pf->width ? pf->width[ch] : pf->maxwidth;
|
|
|
|
if (ofs > width)
|
|
{
|
|
ofs -= width;
|
|
continue;
|
|
}
|
|
|
|
bits = pf->bits + (pf->offset ?
|
|
pf->offset[ch] : ((pf->height + 7) / 8 * pf->maxwidth * ch));
|
|
|
|
lcd_remote_bitmap_part(bits, ofs, 0, width, x, y, width - ofs,
|
|
pf->height);
|
|
|
|
x += width - ofs;
|
|
ofs = 0;
|
|
}
|
|
}
|
|
|
|
/* put a string at a given pixel position */
|
|
void lcd_remote_putsxy(int x, int y, const unsigned char *str)
|
|
{
|
|
lcd_remote_putsxyofs(x, y, 0, str);
|
|
}
|
|
|
|
/*** line oriented text output ***/
|
|
|
|
/* put a string at a given char position */
|
|
void lcd_remote_puts(int x, int y, const unsigned char *str)
|
|
{
|
|
lcd_remote_puts_style(x, y, str, STYLE_DEFAULT);
|
|
}
|
|
|
|
void lcd_remote_puts_style(int x, int y, const unsigned char *str, int style)
|
|
{
|
|
int xpos,ypos,w,h;
|
|
int lastmode = drawmode;
|
|
|
|
/* make sure scrolling is turned off on the line we are updating */
|
|
scrolling_lines &= ~(1 << y);
|
|
|
|
if(!str || !str[0])
|
|
return;
|
|
|
|
lcd_remote_getstringsize(str, &w, &h);
|
|
xpos = xmargin + x*w / strlen(str);
|
|
ypos = ymargin + y*h;
|
|
lcd_remote_putsxy(xpos, ypos, str);
|
|
drawmode = (DRMODE_SOLID|DRMODE_INVERSEVID);
|
|
lcd_remote_fillrect(xpos + w, ypos, LCD_REMOTE_WIDTH - (xpos + w), h);
|
|
if (style & STYLE_INVERT)
|
|
{
|
|
drawmode = DRMODE_COMPLEMENT;
|
|
lcd_remote_fillrect(xpos, ypos, LCD_REMOTE_WIDTH - xpos, h);
|
|
}
|
|
drawmode = lastmode;
|
|
}
|
|
|
|
/*** scrolling ***/
|
|
|
|
/* Reverse the invert setting of the scrolling line (if any) at given char
|
|
position. Setting will go into affect next time line scrolls. */
|
|
void lcd_remote_invertscroll(int x, int y)
|
|
{
|
|
struct scrollinfo* s;
|
|
|
|
(void)x;
|
|
|
|
s = &scroll[y];
|
|
s->invert = !s->invert;
|
|
}
|
|
|
|
void lcd_remote_stop_scroll(void)
|
|
{
|
|
scrolling_lines=0;
|
|
}
|
|
|
|
void lcd_remote_scroll_speed(int speed)
|
|
{
|
|
scroll_ticks = scroll_tick_table[speed];
|
|
}
|
|
|
|
void lcd_remote_scroll_step(int step)
|
|
{
|
|
scroll_step = step;
|
|
}
|
|
|
|
void lcd_remote_scroll_delay(int ms)
|
|
{
|
|
scroll_delay = ms / (HZ / 10);
|
|
}
|
|
|
|
void lcd_remote_bidir_scroll(int percent)
|
|
{
|
|
bidir_limit = percent;
|
|
}
|
|
|
|
void lcd_remote_puts_scroll(int x, int y, const unsigned char *string)
|
|
{
|
|
lcd_remote_puts_scroll_style(x, y, string, STYLE_DEFAULT);
|
|
}
|
|
|
|
void lcd_remote_puts_scroll_style(int x, int y, const unsigned char *string, int style)
|
|
{
|
|
struct scrollinfo* s;
|
|
int w, h;
|
|
|
|
s = &scroll[y];
|
|
|
|
s->start_tick = current_tick + scroll_delay;
|
|
s->invert = false;
|
|
if (style & STYLE_INVERT) {
|
|
s->invert = true;
|
|
lcd_remote_puts_style(x,y,string,STYLE_INVERT);
|
|
}
|
|
else
|
|
lcd_remote_puts(x,y,string);
|
|
|
|
lcd_remote_getstringsize(string, &w, &h);
|
|
|
|
if (LCD_REMOTE_WIDTH - x * 8 - xmargin < w) {
|
|
/* prepare scroll line */
|
|
char *end;
|
|
|
|
memset(s->line, 0, sizeof s->line);
|
|
strcpy(s->line, string);
|
|
|
|
/* get width */
|
|
s->width = lcd_remote_getstringsize(s->line, &w, &h);
|
|
|
|
/* scroll bidirectional or forward only depending on the string
|
|
width */
|
|
if ( bidir_limit ) {
|
|
s->bidir = s->width < (LCD_REMOTE_WIDTH - xmargin) *
|
|
(100 + bidir_limit) / 100;
|
|
}
|
|
else
|
|
s->bidir = false;
|
|
|
|
if (!s->bidir) { /* add spaces if scrolling in the round */
|
|
strcat(s->line, " ");
|
|
/* get new width incl. spaces */
|
|
s->width = lcd_remote_getstringsize(s->line, &w, &h);
|
|
}
|
|
|
|
end = strchr(s->line, '\0');
|
|
strncpy(end, string, LCD_REMOTE_WIDTH/2);
|
|
|
|
s->len = strlen(string);
|
|
s->offset = 0;
|
|
s->startx = x;
|
|
s->backward = false;
|
|
scrolling_lines |= (1<<y);
|
|
}
|
|
else
|
|
/* force a bit switch-off since it doesn't scroll */
|
|
scrolling_lines &= ~(1<<y);
|
|
}
|
|
|
|
static void scroll_thread(void)
|
|
{
|
|
struct font* pf;
|
|
struct scrollinfo* s;
|
|
int index;
|
|
int xpos, ypos;
|
|
int lastmode;
|
|
|
|
/* initialize scroll struct array */
|
|
scrolling_lines = 0;
|
|
|
|
while ( 1 ) {
|
|
|
|
#ifndef SIMULATOR
|
|
if (init_remote) /* request to initialize the remote lcd */
|
|
{
|
|
init_remote = false; /* clear request */
|
|
remote_lcd_init();
|
|
lcd_remote_update();
|
|
}
|
|
#endif
|
|
for ( index = 0; index < SCROLLABLE_LINES; index++ ) {
|
|
/* really scroll? */
|
|
if ( !(scrolling_lines&(1<<index)) )
|
|
continue;
|
|
|
|
s = &scroll[index];
|
|
|
|
/* check pause */
|
|
if (TIME_BEFORE(current_tick, s->start_tick))
|
|
continue;
|
|
|
|
if (s->backward)
|
|
s->offset -= scroll_step;
|
|
else
|
|
s->offset += scroll_step;
|
|
|
|
pf = font_get(curfont);
|
|
xpos = xmargin + s->startx * s->width / s->len;
|
|
ypos = ymargin + index * pf->height;
|
|
|
|
if (s->bidir) { /* scroll bidirectional */
|
|
if (s->offset <= 0) {
|
|
/* at beginning of line */
|
|
s->offset = 0;
|
|
s->backward = false;
|
|
s->start_tick = current_tick + scroll_delay * 2;
|
|
}
|
|
if (s->offset >= s->width - (LCD_REMOTE_WIDTH - xpos)) {
|
|
/* at end of line */
|
|
s->offset = s->width - (LCD_REMOTE_WIDTH - xpos);
|
|
s->backward = true;
|
|
s->start_tick = current_tick + scroll_delay * 2;
|
|
}
|
|
}
|
|
else {
|
|
/* scroll forward the whole time */
|
|
if (s->offset >= s->width)
|
|
s->offset %= s->width;
|
|
}
|
|
|
|
lastmode = drawmode;
|
|
drawmode = (DRMODE_SOLID|DRMODE_INVERSEVID);
|
|
lcd_remote_fillrect(xpos, ypos, LCD_REMOTE_WIDTH - xpos, pf->height);
|
|
drawmode = DRMODE_SOLID;
|
|
lcd_remote_putsxyofs(xpos, ypos, s->offset, s->line);
|
|
if (s->invert)
|
|
{
|
|
drawmode = DRMODE_COMPLEMENT;
|
|
lcd_remote_fillrect(xpos, ypos, LCD_REMOTE_WIDTH - xpos, pf->height);
|
|
}
|
|
drawmode = lastmode;
|
|
lcd_remote_update_rect(xpos, ypos, LCD_REMOTE_WIDTH - xpos, pf->height);
|
|
}
|
|
|
|
sleep(scroll_ticks);
|
|
}
|
|
}
|
|
|