eac1ca22bd
NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
75 lines
2.5 KiB
C
75 lines
2.5 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2011 by Amaury Pouly
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#ifndef SYSTEM_TARGET_H
|
|
#define SYSTEM_TARGET_H
|
|
|
|
#include "system-arm.h"
|
|
#include "mmu-arm.h"
|
|
#include "panic.h"
|
|
#include "clkctrl-imx233.h"
|
|
#include "icoll-imx233.h"
|
|
#include "clock-target.h" /* CPUFREQ_* are defined here */
|
|
|
|
/**
|
|
* Absolute maximum CPU speed: 454.74 MHz (STMP3780), 320.00 MHz (STMP3700)
|
|
* Intermediate CPU speeds: 261.82 MHz, 64 MHz
|
|
* Absolute minimum CPU speed: 24 MHz */
|
|
#define IMX233_CPUFREQ_454_MHz 454740
|
|
#define IMX233_CPUFREQ_320_MHz 320000
|
|
#define IMX233_CPUFREQ_261_MHz 261820
|
|
#define IMX233_CPUFREQ_64_MHz 64000
|
|
#define IMX233_CPUFREQ_24_MHz 24000
|
|
|
|
#define CPUFREQ_DEFAULT IMX233_CPUFREQ_64_MHz
|
|
#define CPUFREQ_NORMAL IMX233_CPUFREQ_64_MHz
|
|
#if IMX233_SUBTARGET >= 3780
|
|
#define CPUFREQ_MAX IMX233_CPUFREQ_454_MHz
|
|
#elif IMX233_SUBTARGET >= 3700
|
|
#define CPUFREQ_MAX IMX233_CPUFREQ_320_MHz
|
|
#endif
|
|
#define CPUFREQ_SLEEP IMX233_CPUFREQ_64_MHz
|
|
|
|
void system_prepare_fw_start(void);
|
|
void udelay(unsigned us);
|
|
bool imx233_us_elapsed(uint32_t ref, unsigned us_delay);
|
|
void imx233_reset_block(volatile uint32_t *block_reg);
|
|
void power_off(void);
|
|
void imx233_enable_usb_controller(bool enable);
|
|
void imx233_enable_usb_phy(bool enable);
|
|
// NOTE: this is available even if HAVE_ADJUSTABLE_CPU_FREQ is undef
|
|
void imx233_set_cpu_frequency(long frequency);
|
|
|
|
void udelay(unsigned usecs);
|
|
|
|
static inline void mdelay(unsigned msecs)
|
|
{
|
|
udelay(1000 * msecs);
|
|
}
|
|
|
|
void usb_insert_int(void);
|
|
void usb_remove_int(void);
|
|
|
|
bool dbg_hw_target_info(void);
|
|
|
|
/* for watchdog */
|
|
void imx233_keep_alive(void);
|
|
|
|
#endif /* SYSTEM_TARGET_H */
|