b37e6bc8c1
Change all lcd drivers to using a pointer to the static framebuffer instead of directly accessing the static array. This will let us later do fun things like dynamic framebuffer sizes (RaaA) or ability to use different buffers for different layers (dynamic skin backdrops!) Change-Id: I0a4d58a9d7b55e6c932131b929e5d4c9f9414b06
224 lines
7.3 KiB
C
224 lines
7.3 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2002 by Alan Korr
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#include "config.h"
|
|
|
|
#include "kernel.h"
|
|
#include "lcd.h"
|
|
#include "system.h"
|
|
|
|
/*** definitions ***/
|
|
|
|
#define LCD_SET_LOWER_COLUMN_ADDRESS ((char)0x00)
|
|
#define LCD_SET_HIGHER_COLUMN_ADDRESS ((char)0x10)
|
|
#define LCD_SET_INTERNAL_REGULATOR_RESISTOR_RATIO ((char)0x20)
|
|
#define LCD_SET_POWER_CONTROL_REGISTER ((char)0x28)
|
|
#define LCD_SET_DISPLAY_START_LINE ((char)0x40)
|
|
#define LCD_SET_CONTRAST_CONTROL_REGISTER ((char)0x81)
|
|
#define LCD_SET_SEGMENT_REMAP ((char)0xA0)
|
|
#define LCD_SET_LCD_BIAS ((char)0xA2)
|
|
#define LCD_SET_ENTIRE_DISPLAY_OFF ((char)0xA4)
|
|
#define LCD_SET_ENTIRE_DISPLAY_ON ((char)0xA5)
|
|
#define LCD_SET_NORMAL_DISPLAY ((char)0xA6)
|
|
#define LCD_SET_REVERSE_DISPLAY ((char)0xA7)
|
|
#define LCD_SET_MULTIPLEX_RATIO ((char)0xA8)
|
|
#define LCD_SET_BIAS_TC_OSC ((char)0xA9)
|
|
#define LCD_SET_1OVER4_BIAS_RATIO ((char)0xAA)
|
|
#define LCD_SET_INDICATOR_OFF ((char)0xAC)
|
|
#define LCD_SET_INDICATOR_ON ((char)0xAD)
|
|
#define LCD_SET_DISPLAY_OFF ((char)0xAE)
|
|
#define LCD_SET_DISPLAY_ON ((char)0xAF)
|
|
#define LCD_SET_PAGE_ADDRESS ((char)0xB0)
|
|
#define LCD_SET_COM_OUTPUT_SCAN_DIRECTION ((char)0xC0)
|
|
#define LCD_SET_TOTAL_FRAME_PHASES ((char)0xD2)
|
|
#define LCD_SET_DISPLAY_OFFSET ((char)0xD3)
|
|
#define LCD_SET_READ_MODIFY_WRITE_MODE ((char)0xE0)
|
|
#define LCD_SOFTWARE_RESET ((char)0xE2)
|
|
#define LCD_NOP ((char)0xE3)
|
|
#define LCD_SET_END_OF_READ_MODIFY_WRITE_MODE ((char)0xEE)
|
|
|
|
/* LCD command codes */
|
|
#define LCD_CNTL_RESET 0xe2 /* Software reset */
|
|
#define LCD_CNTL_POWER 0x2f /* Power control */
|
|
#define LCD_CNTL_CONTRAST 0x81 /* Contrast */
|
|
#define LCD_CNTL_OUTSCAN 0xc8 /* Output scan direction */
|
|
#define LCD_CNTL_SEGREMAP 0xa1 /* Segment remap */
|
|
#define LCD_CNTL_DISPON 0xaf /* Display on */
|
|
|
|
#define LCD_CNTL_PAGE 0xb0 /* Page address */
|
|
#define LCD_CNTL_HIGHCOL 0x10 /* Upper column address */
|
|
#define LCD_CNTL_LOWCOL 0x00 /* Lower column address */
|
|
|
|
/*** driver routines ***/
|
|
|
|
void lcd_write_command(int cmd)
|
|
{
|
|
while ((LCDSTAT & 3) != 3);
|
|
LCDCMD = cmd;
|
|
}
|
|
|
|
void lcd_write_data( const unsigned char* data, int count )
|
|
{
|
|
int i;
|
|
for (i=0; i < count; i++) {
|
|
while ((LCDSTAT & 3) != 3);
|
|
LCDDATA = data[i];
|
|
}
|
|
}
|
|
|
|
/*** hardware configuration ***/
|
|
|
|
int lcd_default_contrast(void)
|
|
{
|
|
return 45;
|
|
}
|
|
|
|
void lcd_set_contrast(int val)
|
|
{
|
|
lcd_write_command(LCD_CNTL_CONTRAST);
|
|
lcd_write_command(val);
|
|
}
|
|
|
|
void lcd_set_invert_display(bool yesno)
|
|
{
|
|
if (yesno)
|
|
lcd_write_command(LCD_SET_REVERSE_DISPLAY);
|
|
else
|
|
lcd_write_command(LCD_SET_NORMAL_DISPLAY);
|
|
}
|
|
|
|
/* turn the display upside down (call lcd_update() afterwards) */
|
|
void lcd_set_flip(bool yesno)
|
|
{
|
|
if (yesno)
|
|
{
|
|
lcd_write_command(LCD_SET_SEGMENT_REMAP);
|
|
lcd_write_command(LCD_SET_COM_OUTPUT_SCAN_DIRECTION);
|
|
}
|
|
else
|
|
{
|
|
lcd_write_command(LCD_SET_SEGMENT_REMAP | 0x01);
|
|
lcd_write_command(LCD_SET_COM_OUTPUT_SCAN_DIRECTION | 0x08);
|
|
}
|
|
}
|
|
|
|
void lcd_init_device(void)
|
|
{
|
|
LCDREG10 = 0xf;
|
|
LCDREG04 = 0x4084;
|
|
|
|
/* inits like the original firmware */
|
|
lcd_write_command(LCD_SOFTWARE_RESET);
|
|
lcd_write_command(LCD_SET_INTERNAL_REGULATOR_RESISTOR_RATIO + 4);
|
|
lcd_write_command(LCD_SET_LCD_BIAS);
|
|
lcd_write_command(LCD_SET_POWER_CONTROL_REGISTER + 7);
|
|
/* power control register: op-amp=1, regulator=1, booster=1 */
|
|
lcd_write_command(LCD_SET_DISPLAY_ON);
|
|
lcd_write_command(LCD_SET_NORMAL_DISPLAY);
|
|
lcd_set_flip(false);
|
|
lcd_write_command(LCD_SET_DISPLAY_START_LINE + 0);
|
|
lcd_set_contrast(lcd_default_contrast());
|
|
lcd_write_command(LCD_SET_PAGE_ADDRESS);
|
|
lcd_write_command(LCD_SET_LOWER_COLUMN_ADDRESS + 0);
|
|
lcd_write_command(LCD_SET_HIGHER_COLUMN_ADDRESS + 0);
|
|
|
|
lcd_clear_display();
|
|
lcd_update();
|
|
}
|
|
|
|
/*** Update functions ***/
|
|
|
|
/* Performance function that works with an external buffer
|
|
note that by and bheight are in 8-pixel units! */
|
|
void lcd_blit_mono(const unsigned char *data, int x, int by, int width,
|
|
int bheight, int stride)
|
|
{
|
|
/* Copy display bitmap to hardware */
|
|
while (bheight--)
|
|
{
|
|
lcd_write_command (LCD_CNTL_PAGE | (by++ & 0xf));
|
|
lcd_write_command (LCD_CNTL_HIGHCOL | (((x+4)>>4) & 0xf));
|
|
lcd_write_command (LCD_CNTL_LOWCOL | ((x+4) & 0xf));
|
|
|
|
lcd_write_data(data, width);
|
|
data += stride;
|
|
}
|
|
}
|
|
|
|
|
|
/* Performance function that works with an external buffer
|
|
note that by and bheight are in 8-pixel units! */
|
|
void lcd_blit_grey_phase(unsigned char *values, unsigned char *phases,
|
|
int x, int by, int width, int bheight, int stride)
|
|
{
|
|
(void)values;
|
|
(void)phases;
|
|
(void)x;
|
|
(void)by;
|
|
(void)width;
|
|
(void)bheight;
|
|
(void)stride;
|
|
}
|
|
|
|
/* Update the display.
|
|
This must be called after all other LCD functions that change the display. */
|
|
void lcd_update(void) ICODE_ATTR;
|
|
void lcd_update(void)
|
|
{
|
|
int y;
|
|
|
|
/* Copy display bitmap to hardware */
|
|
for (y = 0; y < LCD_FBHEIGHT; y++)
|
|
{
|
|
lcd_write_command (LCD_CNTL_PAGE | (y & 0xf));
|
|
lcd_write_command (LCD_CNTL_HIGHCOL);
|
|
lcd_write_command (LCD_CNTL_LOWCOL | 4);
|
|
|
|
lcd_write_data (FBADDR(0, y), LCD_WIDTH);
|
|
}
|
|
}
|
|
|
|
/* Update a fraction of the display. */
|
|
void lcd_update_rect(int, int, int, int) ICODE_ATTR;
|
|
void lcd_update_rect(int x, int y, int width, int height)
|
|
{
|
|
int ymax;
|
|
|
|
/* The Y coordinates have to work on even 8 pixel rows */
|
|
ymax = (y + height-1) >> 3;
|
|
y >>= 3;
|
|
|
|
if(x + width > LCD_WIDTH)
|
|
width = LCD_WIDTH - x;
|
|
if (width <= 0)
|
|
return; /* nothing left to do, 0 is harmful to lcd_write_data() */
|
|
if(ymax >= LCD_FBHEIGHT)
|
|
ymax = LCD_FBHEIGHT-1;
|
|
|
|
/* Copy specified rectange bitmap to hardware */
|
|
for (; y <= ymax; y++)
|
|
{
|
|
lcd_write_command (LCD_CNTL_PAGE | (y & 0xf));
|
|
lcd_write_command (LCD_CNTL_HIGHCOL | (((x+4) >> 4) & 0xf));
|
|
lcd_write_command (LCD_CNTL_LOWCOL | ((x+4) & 0xf));
|
|
|
|
lcd_write_data (FBADDR(x,y), width);
|
|
}
|
|
}
|