b7c87ac5a3
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@11045 a1c6a512-1295-4272-9138-f99709370657
1137 lines
29 KiB
C
1137 lines
29 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2002 by Alan Korr
|
|
*
|
|
* All files in this archive are subject to the GNU General Public License.
|
|
* See the file COPYING in the source tree root for full license agreement.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#include "config.h"
|
|
|
|
#include "lcd.h"
|
|
#include "kernel.h"
|
|
#include "thread.h"
|
|
#include <string.h>
|
|
#include <stdlib.h>
|
|
#include "file.h"
|
|
#include "debug.h"
|
|
#include "system.h"
|
|
#include "font.h"
|
|
#include "hwcompat.h"
|
|
#include "rbunicode.h"
|
|
#include "bidi.h"
|
|
|
|
/*** definitions ***/
|
|
|
|
#define LCD_SET_LOWER_COLUMN_ADDRESS ((char)0x00)
|
|
#define LCD_SET_HIGHER_COLUMN_ADDRESS ((char)0x10)
|
|
#define LCD_SET_INTERNAL_REGULATOR_RESISTOR_RATIO ((char)0x20)
|
|
#define LCD_SET_POWER_CONTROL_REGISTER ((char)0x28)
|
|
#define LCD_SET_DISPLAY_START_LINE ((char)0x40)
|
|
#define LCD_SET_CONTRAST_CONTROL_REGISTER ((char)0x81)
|
|
#define LCD_SET_SEGMENT_REMAP ((char)0xA0)
|
|
#define LCD_SET_LCD_BIAS ((char)0xA2)
|
|
#define LCD_SET_ENTIRE_DISPLAY_OFF ((char)0xA4)
|
|
#define LCD_SET_ENTIRE_DISPLAY_ON ((char)0xA5)
|
|
#define LCD_SET_NORMAL_DISPLAY ((char)0xA6)
|
|
#define LCD_SET_REVERSE_DISPLAY ((char)0xA7)
|
|
#define LCD_SET_MULTIPLEX_RATIO ((char)0xA8)
|
|
#define LCD_SET_BIAS_TC_OSC ((char)0xA9)
|
|
#define LCD_SET_1OVER4_BIAS_RATIO ((char)0xAA)
|
|
#define LCD_SET_INDICATOR_OFF ((char)0xAC)
|
|
#define LCD_SET_INDICATOR_ON ((char)0xAD)
|
|
#define LCD_SET_DISPLAY_OFF ((char)0xAE)
|
|
#define LCD_SET_DISPLAY_ON ((char)0xAF)
|
|
#define LCD_SET_PAGE_ADDRESS ((char)0xB0)
|
|
#define LCD_SET_COM_OUTPUT_SCAN_DIRECTION ((char)0xC0)
|
|
#define LCD_SET_TOTAL_FRAME_PHASES ((char)0xD2)
|
|
#define LCD_SET_DISPLAY_OFFSET ((char)0xD3)
|
|
#define LCD_SET_READ_MODIFY_WRITE_MODE ((char)0xE0)
|
|
#define LCD_SOFTWARE_RESET ((char)0xE2)
|
|
#define LCD_NOP ((char)0xE3)
|
|
#define LCD_SET_END_OF_READ_MODIFY_WRITE_MODE ((char)0xEE)
|
|
|
|
/* LCD command codes */
|
|
#define LCD_CNTL_RESET 0xe2 /* Software reset */
|
|
#define LCD_CNTL_POWER 0x2f /* Power control */
|
|
#define LCD_CNTL_CONTRAST 0x81 /* Contrast */
|
|
#define LCD_CNTL_OUTSCAN 0xc8 /* Output scan direction */
|
|
#define LCD_CNTL_SEGREMAP 0xa1 /* Segment remap */
|
|
#define LCD_CNTL_DISPON 0xaf /* Display on */
|
|
|
|
#define LCD_CNTL_PAGE 0xb0 /* Page address */
|
|
#define LCD_CNTL_HIGHCOL 0x10 /* Upper column address */
|
|
#define LCD_CNTL_LOWCOL 0x00 /* Lower column address */
|
|
|
|
#define SCROLLABLE_LINES 13
|
|
|
|
/*** globals ***/
|
|
|
|
unsigned char lcd_framebuffer[LCD_HEIGHT/8][LCD_WIDTH];
|
|
|
|
static int drawmode = DRMODE_SOLID;
|
|
static int xmargin = 0;
|
|
static int ymargin = 0;
|
|
static int curfont = FONT_SYSFIXED;
|
|
#ifndef SIMULATOR
|
|
static int xoffset; /* needed for flip */
|
|
#endif
|
|
|
|
/* scrolling */
|
|
static volatile int scrolling_lines=0; /* Bitpattern of which lines are scrolling */
|
|
static void scroll_thread(void);
|
|
static char scroll_stack[DEFAULT_STACK_SIZE];
|
|
static const char scroll_name[] = "scroll";
|
|
static int scroll_ticks = 12; /* # of ticks between updates*/
|
|
static int scroll_delay = HZ/2; /* ticks delay before start */
|
|
static int scroll_step = 6; /* pixels per scroll step */
|
|
static int bidir_limit = 50; /* percent */
|
|
static struct scrollinfo scroll[SCROLLABLE_LINES];
|
|
|
|
static const char scroll_tick_table[16] = {
|
|
/* Hz values:
|
|
1, 1.25, 1.55, 2, 2.5, 3.12, 4, 5, 6.25, 8.33, 10, 12.5, 16.7, 20, 25, 33 */
|
|
100, 80, 64, 50, 40, 32, 25, 20, 16, 12, 10, 8, 6, 5, 4, 3
|
|
};
|
|
|
|
/*** driver routines ***/
|
|
|
|
/* optimised archos recorder code is in lcd.S */
|
|
|
|
#if CONFIG_CPU == TCC730
|
|
/* Optimization opportunity:
|
|
In the following I do exactly as in the archos firmware.
|
|
There is probably a better way (ie. do only one mask operation)
|
|
*/
|
|
void lcd_write_command(int cmd) {
|
|
P2 &= 0xF7;
|
|
P2 &= 0xDF;
|
|
P2 &= 0xFB;
|
|
P0 = cmd;
|
|
P2 |= 0x04;
|
|
P2 |= 0x08;
|
|
P2 |= 0x20;
|
|
}
|
|
|
|
void lcd_write_data( const unsigned char* data, int count ) {
|
|
int i;
|
|
for (i=0; i < count; i++) {
|
|
P2 |= 0x08;
|
|
P2 &= 0xDF;
|
|
P2 &= 0xFB;
|
|
P0 = data[i];
|
|
P2 |= 0x04;
|
|
P2 |= 0x08;
|
|
P2 |= 0x20;
|
|
}
|
|
}
|
|
|
|
#elif CONFIG_CPU == PNX0101
|
|
|
|
void lcd_write_command(int cmd)
|
|
{
|
|
while ((LCDSTAT & 3) != 3);
|
|
LCDCMD = cmd;
|
|
}
|
|
|
|
void lcd_write_data( const unsigned char* data, int count )
|
|
{
|
|
int i;
|
|
for (i=0; i < count; i++) {
|
|
while ((LCDSTAT & 3) != 3);
|
|
LCDDATA = data[i];
|
|
}
|
|
}
|
|
|
|
#endif
|
|
|
|
/*** hardware configuration ***/
|
|
|
|
#ifndef SIMULATOR
|
|
|
|
int lcd_default_contrast(void)
|
|
{
|
|
#if CONFIG_LCD == LCD_GMINI100
|
|
return 31;
|
|
#elif CONFIG_LCD == LCD_IFP7XX
|
|
return 45;
|
|
#else
|
|
return (read_hw_mask() & LCD_CONTRAST_BIAS) ? 31 : 49;
|
|
#endif
|
|
}
|
|
|
|
void lcd_set_contrast(int val)
|
|
{
|
|
lcd_write_command(LCD_CNTL_CONTRAST);
|
|
lcd_write_command(val);
|
|
}
|
|
|
|
void lcd_set_invert_display(bool yesno)
|
|
{
|
|
if (yesno)
|
|
lcd_write_command(LCD_SET_REVERSE_DISPLAY);
|
|
else
|
|
lcd_write_command(LCD_SET_NORMAL_DISPLAY);
|
|
}
|
|
|
|
/* turn the display upside down (call lcd_update() afterwards) */
|
|
void lcd_set_flip(bool yesno)
|
|
{
|
|
#ifdef HAVE_DISPLAY_FLIPPED
|
|
if (!yesno)
|
|
#else
|
|
if (yesno)
|
|
#endif
|
|
#if CONFIG_LCD == LCD_GMINI100
|
|
{
|
|
lcd_write_command(LCD_SET_SEGMENT_REMAP | 0x01);
|
|
lcd_write_command(LCD_SET_COM_OUTPUT_SCAN_DIRECTION | 0x08);
|
|
xoffset = 132 - LCD_WIDTH;
|
|
}
|
|
else
|
|
{
|
|
lcd_write_command(LCD_SET_SEGMENT_REMAP);
|
|
lcd_write_command(LCD_SET_COM_OUTPUT_SCAN_DIRECTION | 0x08);
|
|
xoffset = 0;
|
|
}
|
|
#else
|
|
|
|
{
|
|
lcd_write_command(LCD_SET_SEGMENT_REMAP);
|
|
lcd_write_command(LCD_SET_COM_OUTPUT_SCAN_DIRECTION);
|
|
xoffset = 132 - LCD_WIDTH; /* 132 colums minus the 112 we have */
|
|
}
|
|
else
|
|
{
|
|
lcd_write_command(LCD_SET_SEGMENT_REMAP | 0x01);
|
|
lcd_write_command(LCD_SET_COM_OUTPUT_SCAN_DIRECTION | 0x08);
|
|
#if CONFIG_LCD == LCD_IFP7XX
|
|
xoffset = 4;
|
|
#else
|
|
xoffset = 0;
|
|
#endif
|
|
}
|
|
#endif
|
|
}
|
|
|
|
#endif /* !SIMULATOR */
|
|
|
|
/* LCD init */
|
|
#ifdef SIMULATOR
|
|
|
|
void lcd_init(void)
|
|
{
|
|
create_thread(scroll_thread, scroll_stack,
|
|
sizeof(scroll_stack), scroll_name IF_PRIO(, PRIORITY_USER_INTERFACE));
|
|
}
|
|
#else
|
|
|
|
void lcd_init(void)
|
|
{
|
|
#if CONFIG_CPU == TCC730
|
|
/* Initialise P0 & some P2 output pins:
|
|
P0 -> all pins normal cmos output
|
|
P2 -> pins 1 to 5 normal cmos output. */
|
|
P0CON = 0xff;
|
|
P2CONL |= 0x5a;
|
|
P2CONL &= 0x5b;
|
|
P2CONH |= 1;
|
|
#elif CONFIG_CPU == PNX0101
|
|
LCDREG10 = 0xf;
|
|
LCDREG04 = 0x4084;
|
|
#else
|
|
/* Initialize PB0-3 as output pins */
|
|
PBCR2 &= 0xff00; /* MD = 00 */
|
|
PBIOR |= 0x000f; /* IOR = 1 */
|
|
#endif
|
|
|
|
/* inits like the original firmware */
|
|
lcd_write_command(LCD_SOFTWARE_RESET);
|
|
lcd_write_command(LCD_SET_INTERNAL_REGULATOR_RESISTOR_RATIO + 4);
|
|
#if CONFIG_LCD == LCD_IFP7XX
|
|
lcd_write_command(LCD_SET_LCD_BIAS);
|
|
#else
|
|
lcd_write_command(LCD_SET_1OVER4_BIAS_RATIO + 0); /* force 1/4 bias: 0 */
|
|
#endif
|
|
lcd_write_command(LCD_SET_POWER_CONTROL_REGISTER + 7);
|
|
/* power control register: op-amp=1, regulator=1, booster=1 */
|
|
lcd_write_command(LCD_SET_DISPLAY_ON);
|
|
lcd_write_command(LCD_SET_NORMAL_DISPLAY);
|
|
lcd_set_flip(false);
|
|
lcd_write_command(LCD_SET_DISPLAY_START_LINE + 0);
|
|
lcd_set_contrast(lcd_default_contrast());
|
|
lcd_write_command(LCD_SET_PAGE_ADDRESS);
|
|
lcd_write_command(LCD_SET_LOWER_COLUMN_ADDRESS + 0);
|
|
lcd_write_command(LCD_SET_HIGHER_COLUMN_ADDRESS + 0);
|
|
|
|
lcd_clear_display();
|
|
lcd_update();
|
|
|
|
create_thread(scroll_thread, scroll_stack,
|
|
sizeof(scroll_stack), scroll_name IF_PRIO(, PRIORITY_USER_INTERFACE));
|
|
}
|
|
|
|
/*** Update functions ***/
|
|
|
|
/* Performance function that works with an external buffer
|
|
note that by and bheight are in 8-pixel units! */
|
|
void lcd_blit(const unsigned char* data, int x, int by, int width,
|
|
int bheight, int stride)
|
|
{
|
|
/* Copy display bitmap to hardware */
|
|
while (bheight--)
|
|
{
|
|
lcd_write_command (LCD_CNTL_PAGE | (by++ & 0xf));
|
|
lcd_write_command (LCD_CNTL_HIGHCOL | (((x+xoffset)>>4) & 0xf));
|
|
lcd_write_command (LCD_CNTL_LOWCOL | ((x+xoffset) & 0xf));
|
|
|
|
lcd_write_data(data, width);
|
|
data += stride;
|
|
}
|
|
}
|
|
|
|
|
|
/* Update the display.
|
|
This must be called after all other LCD functions that change the display. */
|
|
void lcd_update(void) ICODE_ATTR;
|
|
void lcd_update(void)
|
|
{
|
|
int y;
|
|
|
|
/* Copy display bitmap to hardware */
|
|
for (y = 0; y < LCD_HEIGHT/8; y++)
|
|
{
|
|
lcd_write_command (LCD_CNTL_PAGE | (y & 0xf));
|
|
lcd_write_command (LCD_CNTL_HIGHCOL | ((xoffset >> 4) & 0xf));
|
|
lcd_write_command (LCD_CNTL_LOWCOL | (xoffset & 0xf));
|
|
|
|
lcd_write_data (lcd_framebuffer[y], LCD_WIDTH);
|
|
}
|
|
}
|
|
|
|
/* Update a fraction of the display. */
|
|
void lcd_update_rect(int, int, int, int) ICODE_ATTR;
|
|
void lcd_update_rect(int x, int y, int width, int height)
|
|
{
|
|
int ymax;
|
|
|
|
/* The Y coordinates have to work on even 8 pixel rows */
|
|
ymax = (y + height-1) >> 3;
|
|
y >>= 3;
|
|
|
|
if(x + width > LCD_WIDTH)
|
|
width = LCD_WIDTH - x;
|
|
if (width <= 0)
|
|
return; /* nothing left to do, 0 is harmful to lcd_write_data() */
|
|
if(ymax >= LCD_HEIGHT/8)
|
|
ymax = LCD_HEIGHT/8-1;
|
|
|
|
/* Copy specified rectange bitmap to hardware */
|
|
for (; y <= ymax; y++)
|
|
{
|
|
lcd_write_command (LCD_CNTL_PAGE | (y & 0xf));
|
|
lcd_write_command (LCD_CNTL_HIGHCOL | (((x+xoffset) >> 4) & 0xf));
|
|
lcd_write_command (LCD_CNTL_LOWCOL | ((x+xoffset) & 0xf));
|
|
|
|
lcd_write_data (&lcd_framebuffer[y][x], width);
|
|
}
|
|
}
|
|
#endif /* !SIMULATOR */
|
|
|
|
/*** parameter handling ***/
|
|
|
|
void lcd_set_drawmode(int mode)
|
|
{
|
|
drawmode = mode & (DRMODE_SOLID|DRMODE_INVERSEVID);
|
|
}
|
|
|
|
int lcd_get_drawmode(void)
|
|
{
|
|
return drawmode;
|
|
}
|
|
|
|
void lcd_setmargins(int x, int y)
|
|
{
|
|
xmargin = x;
|
|
ymargin = y;
|
|
}
|
|
|
|
int lcd_getxmargin(void)
|
|
{
|
|
return xmargin;
|
|
}
|
|
|
|
int lcd_getymargin(void)
|
|
{
|
|
return ymargin;
|
|
}
|
|
|
|
void lcd_setfont(int newfont)
|
|
{
|
|
curfont = newfont;
|
|
}
|
|
|
|
int lcd_getstringsize(const unsigned char *str, int *w, int *h)
|
|
{
|
|
return font_getstringsize(str, w, h, curfont);
|
|
}
|
|
|
|
/*** low-level drawing functions ***/
|
|
|
|
static void setpixel(int x, int y)
|
|
{
|
|
lcd_framebuffer[y>>3][x] |= 1 << (y & 7);
|
|
}
|
|
|
|
static void clearpixel(int x, int y)
|
|
{
|
|
lcd_framebuffer[y>>3][x] &= ~(1 << (y & 7));
|
|
}
|
|
|
|
static void flippixel(int x, int y)
|
|
{
|
|
lcd_framebuffer[y>>3][x] ^= 1 << (y & 7);
|
|
}
|
|
|
|
static void nopixel(int x, int y)
|
|
{
|
|
(void)x;
|
|
(void)y;
|
|
}
|
|
|
|
lcd_pixelfunc_type* const lcd_pixelfuncs[8] = {
|
|
flippixel, nopixel, setpixel, setpixel,
|
|
nopixel, clearpixel, nopixel, clearpixel
|
|
};
|
|
|
|
static void flipblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void flipblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address ^= bits & mask;
|
|
}
|
|
|
|
static void bgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void bgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address &= bits | ~mask;
|
|
}
|
|
|
|
static void fgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void fgblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address |= bits & mask;
|
|
}
|
|
|
|
static void solidblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void solidblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
unsigned data = *(char*)address;
|
|
|
|
bits ^= data;
|
|
*address = data ^ (bits & mask);
|
|
}
|
|
|
|
static void flipinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void flipinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address ^= ~bits & mask;
|
|
}
|
|
|
|
static void bginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void bginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address &= ~(bits & mask);
|
|
}
|
|
|
|
static void fginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void fginvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
*address |= ~bits & mask;
|
|
}
|
|
|
|
static void solidinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
ICODE_ATTR;
|
|
static void solidinvblock(unsigned char *address, unsigned mask, unsigned bits)
|
|
{
|
|
unsigned data = *(char *)address;
|
|
|
|
bits = ~bits ^ data;
|
|
*address = data ^ (bits & mask);
|
|
}
|
|
|
|
lcd_blockfunc_type* const lcd_blockfuncs[8] = {
|
|
flipblock, bgblock, fgblock, solidblock,
|
|
flipinvblock, bginvblock, fginvblock, solidinvblock
|
|
};
|
|
|
|
/*** drawing functions ***/
|
|
|
|
/* Clear the whole display */
|
|
void lcd_clear_display(void)
|
|
{
|
|
unsigned bits = (drawmode & DRMODE_INVERSEVID) ? 0xFFu : 0;
|
|
|
|
memset(lcd_framebuffer, bits, sizeof lcd_framebuffer);
|
|
scrolling_lines = 0;
|
|
}
|
|
|
|
/* Set a single pixel */
|
|
void lcd_drawpixel(int x, int y)
|
|
{
|
|
if (((unsigned)x < LCD_WIDTH) && ((unsigned)y < LCD_HEIGHT))
|
|
lcd_pixelfuncs[drawmode](x, y);
|
|
}
|
|
|
|
/* Draw a line */
|
|
void lcd_drawline(int x1, int y1, int x2, int y2)
|
|
{
|
|
int numpixels;
|
|
int i;
|
|
int deltax, deltay;
|
|
int d, dinc1, dinc2;
|
|
int x, xinc1, xinc2;
|
|
int y, yinc1, yinc2;
|
|
lcd_pixelfunc_type *pfunc = lcd_pixelfuncs[drawmode];
|
|
|
|
deltax = abs(x2 - x1);
|
|
deltay = abs(y2 - y1);
|
|
xinc2 = 1;
|
|
yinc2 = 1;
|
|
|
|
if (deltax >= deltay)
|
|
{
|
|
numpixels = deltax;
|
|
d = 2 * deltay - deltax;
|
|
dinc1 = deltay * 2;
|
|
dinc2 = (deltay - deltax) * 2;
|
|
xinc1 = 1;
|
|
yinc1 = 0;
|
|
}
|
|
else
|
|
{
|
|
numpixels = deltay;
|
|
d = 2 * deltax - deltay;
|
|
dinc1 = deltax * 2;
|
|
dinc2 = (deltax - deltay) * 2;
|
|
xinc1 = 0;
|
|
yinc1 = 1;
|
|
}
|
|
numpixels++; /* include endpoints */
|
|
|
|
if (x1 > x2)
|
|
{
|
|
xinc1 = -xinc1;
|
|
xinc2 = -xinc2;
|
|
}
|
|
|
|
if (y1 > y2)
|
|
{
|
|
yinc1 = -yinc1;
|
|
yinc2 = -yinc2;
|
|
}
|
|
|
|
x = x1;
|
|
y = y1;
|
|
|
|
for (i = 0; i < numpixels; i++)
|
|
{
|
|
if (((unsigned)x < LCD_WIDTH) && ((unsigned)y < LCD_HEIGHT))
|
|
pfunc(x, y);
|
|
|
|
if (d < 0)
|
|
{
|
|
d += dinc1;
|
|
x += xinc1;
|
|
y += yinc1;
|
|
}
|
|
else
|
|
{
|
|
d += dinc2;
|
|
x += xinc2;
|
|
y += yinc2;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* Draw a horizontal line (optimised) */
|
|
void lcd_hline(int x1, int x2, int y)
|
|
{
|
|
int x;
|
|
unsigned char *dst, *dst_end;
|
|
unsigned mask;
|
|
lcd_blockfunc_type *bfunc;
|
|
|
|
/* direction flip */
|
|
if (x2 < x1)
|
|
{
|
|
x = x1;
|
|
x1 = x2;
|
|
x2 = x;
|
|
}
|
|
|
|
/* nothing to draw? */
|
|
if (((unsigned)y >= LCD_HEIGHT) || (x1 >= LCD_WIDTH) || (x2 < 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (x1 < 0)
|
|
x1 = 0;
|
|
if (x2 >= LCD_WIDTH)
|
|
x2 = LCD_WIDTH-1;
|
|
|
|
bfunc = lcd_blockfuncs[drawmode];
|
|
dst = &lcd_framebuffer[y>>3][x1];
|
|
mask = 1 << (y & 7);
|
|
|
|
dst_end = dst + x2 - x1;
|
|
do
|
|
bfunc(dst++, mask, 0xFFu);
|
|
while (dst <= dst_end);
|
|
}
|
|
|
|
/* Draw a vertical line (optimised) */
|
|
void lcd_vline(int x, int y1, int y2)
|
|
{
|
|
int ny;
|
|
unsigned char *dst;
|
|
unsigned mask, mask_bottom;
|
|
lcd_blockfunc_type *bfunc;
|
|
|
|
/* direction flip */
|
|
if (y2 < y1)
|
|
{
|
|
ny = y1;
|
|
y1 = y2;
|
|
y2 = ny;
|
|
}
|
|
|
|
/* nothing to draw? */
|
|
if (((unsigned)x >= LCD_WIDTH) || (y1 >= LCD_HEIGHT) || (y2 < 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (y1 < 0)
|
|
y1 = 0;
|
|
if (y2 >= LCD_HEIGHT)
|
|
y2 = LCD_HEIGHT-1;
|
|
|
|
bfunc = lcd_blockfuncs[drawmode];
|
|
dst = &lcd_framebuffer[y1>>3][x];
|
|
ny = y2 - (y1 & ~7);
|
|
mask = 0xFFu << (y1 & 7);
|
|
mask_bottom = 0xFFu >> (~ny & 7);
|
|
|
|
for (; ny >= 8; ny -= 8)
|
|
{
|
|
bfunc(dst, mask, 0xFFu);
|
|
dst += LCD_WIDTH;
|
|
mask = 0xFFu;
|
|
}
|
|
mask &= mask_bottom;
|
|
bfunc(dst, mask, 0xFFu);
|
|
}
|
|
|
|
/* Draw a rectangular box */
|
|
void lcd_drawrect(int x, int y, int width, int height)
|
|
{
|
|
if ((width <= 0) || (height <= 0))
|
|
return;
|
|
|
|
int x2 = x + width - 1;
|
|
int y2 = y + height - 1;
|
|
|
|
lcd_vline(x, y, y2);
|
|
lcd_vline(x2, y, y2);
|
|
lcd_hline(x, x2, y);
|
|
lcd_hline(x, x2, y2);
|
|
}
|
|
|
|
/* Fill a rectangular area */
|
|
void lcd_fillrect(int x, int y, int width, int height)
|
|
{
|
|
int ny;
|
|
unsigned char *dst, *dst_end;
|
|
unsigned mask, mask_bottom;
|
|
unsigned bits = 0;
|
|
lcd_blockfunc_type *bfunc;
|
|
bool fillopt = false;
|
|
|
|
/* nothing to draw? */
|
|
if ((width <= 0) || (height <= 0) || (x >= LCD_WIDTH) || (y >= LCD_HEIGHT)
|
|
|| (x + width <= 0) || (y + height <= 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (x < 0)
|
|
{
|
|
width += x;
|
|
x = 0;
|
|
}
|
|
if (y < 0)
|
|
{
|
|
height += y;
|
|
y = 0;
|
|
}
|
|
if (x + width > LCD_WIDTH)
|
|
width = LCD_WIDTH - x;
|
|
if (y + height > LCD_HEIGHT)
|
|
height = LCD_HEIGHT - y;
|
|
|
|
if (drawmode & DRMODE_INVERSEVID)
|
|
{
|
|
if (drawmode & DRMODE_BG)
|
|
{
|
|
fillopt = true;
|
|
}
|
|
}
|
|
else
|
|
{
|
|
if (drawmode & DRMODE_FG)
|
|
{
|
|
fillopt = true;
|
|
bits = 0xFFu;
|
|
}
|
|
}
|
|
bfunc = lcd_blockfuncs[drawmode];
|
|
dst = &lcd_framebuffer[y>>3][x];
|
|
ny = height - 1 + (y & 7);
|
|
mask = 0xFFu << (y & 7);
|
|
mask_bottom = 0xFFu >> (~ny & 7);
|
|
|
|
for (; ny >= 8; ny -= 8)
|
|
{
|
|
if (fillopt && (mask == 0xFFu))
|
|
memset(dst, bits, width);
|
|
else
|
|
{
|
|
unsigned char *dst_row = dst;
|
|
|
|
dst_end = dst_row + width;
|
|
do
|
|
bfunc(dst_row++, mask, 0xFFu);
|
|
while (dst_row < dst_end);
|
|
}
|
|
|
|
dst += LCD_WIDTH;
|
|
mask = 0xFFu;
|
|
}
|
|
mask &= mask_bottom;
|
|
|
|
if (fillopt && (mask == 0xFFu))
|
|
memset(dst, bits, width);
|
|
else
|
|
{
|
|
dst_end = dst + width;
|
|
do
|
|
bfunc(dst++, mask, 0xFFu);
|
|
while (dst < dst_end);
|
|
}
|
|
}
|
|
|
|
/* About Rockbox' internal bitmap format:
|
|
*
|
|
* A bitmap contains one bit for every pixel that defines if that pixel is
|
|
* black (1) or white (0). Bits within a byte are arranged vertically, LSB
|
|
* at top.
|
|
* The bytes are stored in row-major order, with byte 0 being top left,
|
|
* byte 1 2nd from left etc. The first row of bytes defines pixel rows
|
|
* 0..7, the second row defines pixel row 8..15 etc.
|
|
*
|
|
* This is the same as the internal lcd hw format. */
|
|
|
|
/* Draw a partial bitmap */
|
|
void lcd_bitmap_part(const unsigned char *src, int src_x, int src_y,
|
|
int stride, int x, int y, int width, int height)
|
|
ICODE_ATTR;
|
|
void lcd_bitmap_part(const unsigned char *src, int src_x, int src_y,
|
|
int stride, int x, int y, int width, int height)
|
|
{
|
|
int shift, ny;
|
|
unsigned char *dst, *dst_end;
|
|
unsigned mask, mask_bottom;
|
|
lcd_blockfunc_type *bfunc;
|
|
|
|
/* nothing to draw? */
|
|
if ((width <= 0) || (height <= 0) || (x >= LCD_WIDTH) || (y >= LCD_HEIGHT)
|
|
|| (x + width <= 0) || (y + height <= 0))
|
|
return;
|
|
|
|
/* clipping */
|
|
if (x < 0)
|
|
{
|
|
width += x;
|
|
src_x -= x;
|
|
x = 0;
|
|
}
|
|
if (y < 0)
|
|
{
|
|
height += y;
|
|
src_y -= y;
|
|
y = 0;
|
|
}
|
|
if (x + width > LCD_WIDTH)
|
|
width = LCD_WIDTH - x;
|
|
if (y + height > LCD_HEIGHT)
|
|
height = LCD_HEIGHT - y;
|
|
|
|
src += stride * (src_y >> 3) + src_x; /* move starting point */
|
|
src_y &= 7;
|
|
y -= src_y;
|
|
dst = &lcd_framebuffer[y>>3][x];
|
|
shift = y & 7;
|
|
ny = height - 1 + shift + src_y;
|
|
|
|
bfunc = lcd_blockfuncs[drawmode];
|
|
mask = 0xFFu << (shift + src_y);
|
|
mask_bottom = 0xFFu >> (~ny & 7);
|
|
|
|
if (shift == 0)
|
|
{
|
|
bool copyopt = (drawmode == DRMODE_SOLID);
|
|
|
|
for (; ny >= 8; ny -= 8)
|
|
{
|
|
if (copyopt && (mask == 0xFFu))
|
|
memcpy(dst, src, width);
|
|
else
|
|
{
|
|
const unsigned char *src_row = src;
|
|
unsigned char *dst_row = dst;
|
|
|
|
dst_end = dst_row + width;
|
|
do
|
|
bfunc(dst_row++, mask, *src_row++);
|
|
while (dst_row < dst_end);
|
|
}
|
|
|
|
src += stride;
|
|
dst += LCD_WIDTH;
|
|
mask = 0xFFu;
|
|
}
|
|
mask &= mask_bottom;
|
|
|
|
if (copyopt && (mask == 0xFFu))
|
|
memcpy(dst, src, width);
|
|
else
|
|
{
|
|
dst_end = dst + width;
|
|
do
|
|
bfunc(dst++, mask, *src++);
|
|
while (dst < dst_end);
|
|
}
|
|
}
|
|
else
|
|
{
|
|
dst_end = dst + width;
|
|
do
|
|
{
|
|
const unsigned char *src_col = src++;
|
|
unsigned char *dst_col = dst++;
|
|
unsigned mask_col = mask;
|
|
unsigned data = 0;
|
|
|
|
for (y = ny; y >= 8; y -= 8)
|
|
{
|
|
data |= *src_col << shift;
|
|
|
|
if (mask_col & 0xFFu)
|
|
{
|
|
bfunc(dst_col, mask_col, data);
|
|
mask_col = 0xFFu;
|
|
}
|
|
else
|
|
mask_col >>= 8;
|
|
|
|
src_col += stride;
|
|
dst_col += LCD_WIDTH;
|
|
data >>= 8;
|
|
}
|
|
data |= *src_col << shift;
|
|
bfunc(dst_col, mask_col & mask_bottom, data);
|
|
}
|
|
while (dst < dst_end);
|
|
}
|
|
}
|
|
|
|
/* Draw a full bitmap */
|
|
void lcd_bitmap(const unsigned char *src, int x, int y, int width, int height)
|
|
{
|
|
lcd_bitmap_part(src, 0, 0, width, x, y, width, height);
|
|
}
|
|
|
|
/* put a string at a given pixel position, skipping first ofs pixel columns */
|
|
static void lcd_putsxyofs(int x, int y, int ofs, const unsigned char *str)
|
|
{
|
|
unsigned short ch;
|
|
unsigned short *ucs;
|
|
struct font* pf = font_get(curfont);
|
|
|
|
ucs = bidi_l2v(str, 1);
|
|
|
|
while ((ch = *ucs++) != 0 && x < LCD_WIDTH)
|
|
{
|
|
int width;
|
|
const unsigned char *bits;
|
|
|
|
/* get proportional width and glyph bits */
|
|
width = font_get_width(pf,ch);
|
|
|
|
if (ofs > width)
|
|
{
|
|
ofs -= width;
|
|
continue;
|
|
}
|
|
|
|
bits = font_get_bits(pf, ch);
|
|
|
|
lcd_mono_bitmap_part(bits, ofs, 0, width, x, y, width - ofs,
|
|
pf->height);
|
|
|
|
x += width - ofs;
|
|
ofs = 0;
|
|
}
|
|
}
|
|
/* put a string at a given pixel position */
|
|
void lcd_putsxy(int x, int y, const unsigned char *str)
|
|
{
|
|
lcd_putsxyofs(x, y, 0, str);
|
|
}
|
|
|
|
/*** Line oriented text output ***/
|
|
|
|
/* put a string at a given char position */
|
|
void lcd_puts(int x, int y, const unsigned char *str)
|
|
{
|
|
lcd_puts_style_offset(x, y, str, STYLE_DEFAULT, 0);
|
|
}
|
|
|
|
void lcd_puts_style(int x, int y, const unsigned char *str, int style)
|
|
{
|
|
lcd_puts_style_offset(x, y, str, style, 0);
|
|
}
|
|
|
|
void lcd_puts_offset(int x, int y, const unsigned char *str, int offset)
|
|
{
|
|
lcd_puts_style_offset(x, y, str, STYLE_DEFAULT, offset);
|
|
}
|
|
|
|
/* put a string at a given char position, style, and pixel position,
|
|
* skipping first offset pixel columns */
|
|
void lcd_puts_style_offset(int x, int y, const unsigned char *str,
|
|
int style, int offset)
|
|
{
|
|
int xpos,ypos,w,h,xrect;
|
|
int lastmode = drawmode;
|
|
|
|
/* make sure scrolling is turned off on the line we are updating */
|
|
scrolling_lines &= ~(1 << y);
|
|
|
|
if(!str || !str[0])
|
|
return;
|
|
|
|
lcd_getstringsize(str, &w, &h);
|
|
xpos = xmargin + x*w / utf8length(str);
|
|
ypos = ymargin + y*h;
|
|
drawmode = (style & STYLE_INVERT) ?
|
|
(DRMODE_SOLID|DRMODE_INVERSEVID) : DRMODE_SOLID;
|
|
lcd_putsxyofs(xpos, ypos, offset, str);
|
|
drawmode ^= DRMODE_INVERSEVID;
|
|
xrect = xpos + MAX(w - offset, 0);
|
|
lcd_fillrect(xrect, ypos, LCD_WIDTH - xrect, h);
|
|
drawmode = lastmode;
|
|
}
|
|
|
|
/*** scrolling ***/
|
|
|
|
/* Reverse the invert setting of the scrolling line (if any) at given char
|
|
position. Setting will go into affect next time line scrolls. */
|
|
void lcd_invertscroll(int x, int y)
|
|
{
|
|
struct scrollinfo* s;
|
|
|
|
(void)x;
|
|
|
|
s = &scroll[y];
|
|
s->invert = !s->invert;
|
|
}
|
|
|
|
void lcd_stop_scroll(void)
|
|
{
|
|
scrolling_lines=0;
|
|
}
|
|
|
|
void lcd_scroll_speed(int speed)
|
|
{
|
|
scroll_ticks = scroll_tick_table[speed];
|
|
}
|
|
|
|
void lcd_scroll_step(int step)
|
|
{
|
|
scroll_step = step;
|
|
}
|
|
|
|
void lcd_scroll_delay(int ms)
|
|
{
|
|
scroll_delay = ms / (HZ / 10);
|
|
}
|
|
|
|
void lcd_bidir_scroll(int percent)
|
|
{
|
|
bidir_limit = percent;
|
|
}
|
|
|
|
void lcd_puts_scroll(int x, int y, const unsigned char *string)
|
|
{
|
|
lcd_puts_scroll_style(x, y, string, STYLE_DEFAULT);
|
|
}
|
|
|
|
void lcd_puts_scroll_style(int x, int y, const unsigned char *string, int style)
|
|
{
|
|
lcd_puts_scroll_style_offset(x, y, string, style, 0);
|
|
}
|
|
|
|
void lcd_puts_scroll_offset(int x, int y, const unsigned char *string,
|
|
int offset)
|
|
{
|
|
lcd_puts_scroll_style_offset(x, y, string, STYLE_DEFAULT, offset);
|
|
}
|
|
|
|
void lcd_puts_scroll_style_offset(int x, int y, const unsigned char *string,
|
|
int style, int offset)
|
|
{
|
|
struct scrollinfo* s;
|
|
int w, h;
|
|
|
|
s = &scroll[y];
|
|
|
|
s->start_tick = current_tick + scroll_delay;
|
|
s->invert = false;
|
|
if (style & STYLE_INVERT) {
|
|
s->invert = true;
|
|
lcd_puts_style_offset(x,y,string,STYLE_INVERT,offset);
|
|
}
|
|
else
|
|
lcd_puts_offset(x,y,string,offset);
|
|
|
|
lcd_getstringsize(string, &w, &h);
|
|
|
|
if (LCD_WIDTH - x * 8 - xmargin < w) {
|
|
/* prepare scroll line */
|
|
char *end;
|
|
|
|
memset(s->line, 0, sizeof s->line);
|
|
strcpy(s->line, string);
|
|
|
|
/* get width */
|
|
s->width = lcd_getstringsize(s->line, &w, &h);
|
|
|
|
/* scroll bidirectional or forward only depending on the string
|
|
width */
|
|
if ( bidir_limit ) {
|
|
s->bidir = s->width < (LCD_WIDTH - xmargin) *
|
|
(100 + bidir_limit) / 100;
|
|
}
|
|
else
|
|
s->bidir = false;
|
|
|
|
if (!s->bidir) { /* add spaces if scrolling in the round */
|
|
strcat(s->line, " ");
|
|
/* get new width incl. spaces */
|
|
s->width = lcd_getstringsize(s->line, &w, &h);
|
|
}
|
|
|
|
end = strchr(s->line, '\0');
|
|
strncpy(end, string, LCD_WIDTH/2);
|
|
|
|
s->len = utf8length(string);
|
|
s->offset = offset;
|
|
s->startx = xmargin + x * s->width / s->len;;
|
|
s->backward = false;
|
|
scrolling_lines |= (1<<y);
|
|
}
|
|
else
|
|
/* force a bit switch-off since it doesn't scroll */
|
|
scrolling_lines &= ~(1<<y);
|
|
}
|
|
|
|
static void scroll_thread(void)
|
|
{
|
|
struct font* pf;
|
|
struct scrollinfo* s;
|
|
int index;
|
|
int xpos, ypos;
|
|
int lastmode;
|
|
|
|
/* initialize scroll struct array */
|
|
scrolling_lines = 0;
|
|
|
|
while ( 1 ) {
|
|
for ( index = 0; index < SCROLLABLE_LINES; index++ ) {
|
|
/* really scroll? */
|
|
if ( !(scrolling_lines&(1<<index)) )
|
|
continue;
|
|
|
|
s = &scroll[index];
|
|
|
|
/* check pause */
|
|
if (TIME_BEFORE(current_tick, s->start_tick))
|
|
continue;
|
|
|
|
if (s->backward)
|
|
s->offset -= scroll_step;
|
|
else
|
|
s->offset += scroll_step;
|
|
|
|
pf = font_get(curfont);
|
|
xpos = s->startx;
|
|
ypos = ymargin + index * pf->height;
|
|
|
|
if (s->bidir) { /* scroll bidirectional */
|
|
if (s->offset <= 0) {
|
|
/* at beginning of line */
|
|
s->offset = 0;
|
|
s->backward = false;
|
|
s->start_tick = current_tick + scroll_delay * 2;
|
|
}
|
|
if (s->offset >= s->width - (LCD_WIDTH - xpos)) {
|
|
/* at end of line */
|
|
s->offset = s->width - (LCD_WIDTH - xpos);
|
|
s->backward = true;
|
|
s->start_tick = current_tick + scroll_delay * 2;
|
|
}
|
|
}
|
|
else {
|
|
/* scroll forward the whole time */
|
|
if (s->offset >= s->width)
|
|
s->offset %= s->width;
|
|
}
|
|
|
|
lastmode = drawmode;
|
|
drawmode = s->invert ?
|
|
(DRMODE_SOLID|DRMODE_INVERSEVID) : DRMODE_SOLID;
|
|
lcd_putsxyofs(xpos, ypos, s->offset, s->line);
|
|
drawmode = lastmode;
|
|
lcd_update_rect(xpos, ypos, LCD_WIDTH - xpos, pf->height);
|
|
}
|
|
|
|
sleep(scroll_ticks);
|
|
}
|
|
}
|
|
|