12fa759aad
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26684 a1c6a512-1295-4272-9138-f99709370657
247 lines
7.2 KiB
C
247 lines
7.2 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id:$
|
|
*
|
|
* Copyright (C) 2010 Marcin Bukat
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#include "config.h"
|
|
|
|
#include "system.h"
|
|
#include "kernel.h"
|
|
#include "lcd.h"
|
|
|
|
/*** definitions ***/
|
|
/* TOMATO LSI 0350 - definitions and slightly tweaked functions
|
|
* taken from lcd-remote-iaudio.c
|
|
*/
|
|
|
|
#define LCD_SET_DUTY_RATIO 0x48
|
|
#define LCD_SELECT_ADC 0xa0
|
|
#define LCD_SELECT_SHL 0xc0
|
|
#define LCD_SET_COM0 0x44
|
|
#define LCD_OSC_ON 0xab
|
|
#define LCD_SELECT_DCDC 0x64
|
|
#define LCD_SELECT_RES 0x20
|
|
#define LCD_SET_VOLUME 0x81
|
|
#define LCD_SET_BIAS 0x50
|
|
#define LCD_CONTROL_POWER 0x28
|
|
#define LCD_DISPLAY_ON 0xae
|
|
#define LCD_SET_INITLINE 0x40
|
|
#define LCD_SET_COLUMN 0x10
|
|
#define LCD_SET_PAGE 0xb0
|
|
#define LCD_SET_GRAY 0x88
|
|
#define LCD_SET_PWM_FRC 0x90
|
|
#define LCD_SET_POWER_SAVE 0xa8
|
|
#define LCD_REVERSE 0xa6
|
|
#define LCD_RESET 0xe2
|
|
|
|
/* cached settings */
|
|
static bool cached_invert = false;
|
|
static bool cached_flip = false;
|
|
static int cached_contrast = DEFAULT_CONTRAST_SETTING;
|
|
|
|
/*** hardware configuration ***/
|
|
int lcd_default_contrast(void)
|
|
{
|
|
return DEFAULT_CONTRAST_SETTING;
|
|
}
|
|
|
|
void lcd_powersave(bool on)
|
|
{
|
|
if (on)
|
|
/* enter power saving mode
|
|
* this turns off lcd without controller reset
|
|
* probably ~1mA saving
|
|
*/
|
|
lcd_write_command(LCD_SET_POWER_SAVE | 1);
|
|
else
|
|
/* leave lcd power saving mode
|
|
* no need to reset and initialize controller
|
|
*/
|
|
lcd_write_command(LCD_SET_POWER_SAVE | 0);
|
|
}
|
|
|
|
void lcd_set_contrast(int val)
|
|
{
|
|
if (val < MIN_CONTRAST_SETTING)
|
|
val = MIN_CONTRAST_SETTING;
|
|
else if (val > MAX_CONTRAST_SETTING)
|
|
val = MAX_CONTRAST_SETTING;
|
|
|
|
cached_contrast = val;
|
|
lcd_write_command_e(LCD_SET_VOLUME, val);
|
|
}
|
|
|
|
void lcd_set_invert_display(bool yesno)
|
|
{
|
|
cached_invert = yesno;
|
|
lcd_write_command(LCD_REVERSE | yesno);
|
|
|
|
}
|
|
|
|
/* turn the display upside down (call lcd_update() afterwards) */
|
|
void lcd_set_flip(bool yesno)
|
|
{
|
|
cached_flip = yesno;
|
|
if(yesno)
|
|
{
|
|
lcd_write_command(LCD_SELECT_ADC | 1);
|
|
lcd_write_command(LCD_SELECT_SHL | 0);
|
|
lcd_write_command_e(LCD_SET_COM0, 0);
|
|
}
|
|
else
|
|
{
|
|
lcd_write_command(LCD_SELECT_ADC | 0);
|
|
lcd_write_command(LCD_SELECT_SHL | 8);
|
|
lcd_write_command_e(LCD_SET_COM0, 0);
|
|
}
|
|
}
|
|
|
|
void lcd_shutdown(void)
|
|
{
|
|
/* Set power save -> Power OFF (VDD - VSS) .. that's it */
|
|
lcd_write_command(LCD_SET_POWER_SAVE | 1);
|
|
}
|
|
|
|
void lcd_init_device(void)
|
|
{
|
|
and_l(~0x00000800, &GPIO_FUNCTION); /* CS3 line */
|
|
|
|
/* LCD Reset GPO34 */
|
|
or_l(0x00000004, &GPIO1_ENABLE); /* set as output */
|
|
or_l(0x00000004, &GPIO1_FUNCTION); /* switch to secondary function - GPIO */
|
|
|
|
and_l(~0x00000004, &GPIO1_OUT); /* RESET low */
|
|
sleep(1); /* delay at least 1000 ns */
|
|
or_l(0x00000004, &GPIO1_OUT); /* RESET high */
|
|
sleep(1);
|
|
|
|
/* parameters setup taken from original firmware */
|
|
lcd_write_command(LCD_RESET);
|
|
lcd_write_command_e(LCD_SET_DUTY_RATIO,0x80); /* 1/128 */
|
|
lcd_write_command(LCD_OSC_ON);
|
|
lcd_write_command(LCD_SELECT_DCDC | 3); /* DC/DC 6xboost */
|
|
lcd_write_command(LCD_SELECT_RES | 7); /* Regulator resistor: 7.2 */
|
|
lcd_write_command(LCD_SET_BIAS | 6); /* 1/11 */
|
|
lcd_write_command(LCD_SET_PWM_FRC | 6); /* 3FRC + 12PWM */
|
|
lcd_write_command_e(LCD_SET_GRAY | 0, 0x00);
|
|
lcd_write_command_e(LCD_SET_GRAY | 1, 0x00);
|
|
lcd_write_command_e(LCD_SET_GRAY | 2, 0x0c);
|
|
lcd_write_command_e(LCD_SET_GRAY | 3, 0x00);
|
|
lcd_write_command_e(LCD_SET_GRAY | 4, 0xc4);
|
|
lcd_write_command_e(LCD_SET_GRAY | 5, 0x00);
|
|
lcd_write_command_e(LCD_SET_GRAY | 6, 0xcc);
|
|
lcd_write_command_e(LCD_SET_GRAY | 7, 0x00);
|
|
|
|
lcd_write_command(LCD_CONTROL_POWER | 7); /* All circuits ON */
|
|
lcd_write_command(LCD_DISPLAY_ON | 1); /* display on */
|
|
|
|
lcd_set_flip(cached_flip);
|
|
lcd_set_contrast(cached_contrast);
|
|
lcd_set_invert_display(cached_invert);
|
|
|
|
lcd_update();
|
|
}
|
|
|
|
/* Update the display.
|
|
This must be called after all other LCD functions that change the display. */
|
|
void lcd_update(void) ICODE_ATTR;
|
|
void lcd_update(void)
|
|
{
|
|
int y;
|
|
|
|
for(y = 0;y < LCD_FBHEIGHT;y++)
|
|
{
|
|
lcd_write_command(LCD_SET_PAGE | y);
|
|
lcd_write_command_e(LCD_SET_COLUMN, 0);
|
|
lcd_write_data(lcd_framebuffer[y], LCD_WIDTH);
|
|
}
|
|
|
|
|
|
}
|
|
|
|
/* Update a fraction of the display. */
|
|
void lcd_update_rect(int, int, int, int) ICODE_ATTR;
|
|
void lcd_update_rect(int x, int y, int width, int height)
|
|
{
|
|
int ymax;
|
|
|
|
/* The Y coordinates have to work on even 8 pixel rows */
|
|
ymax = (y + height-1) >> 3;
|
|
y >>= 3;
|
|
|
|
if (x + width > LCD_WIDTH)
|
|
width = LCD_WIDTH - x;
|
|
|
|
if (width <= 0)
|
|
return; /* nothing left to do, 0 is harmful to lcd_write_data() */
|
|
|
|
if (ymax >= LCD_FBHEIGHT)
|
|
ymax = LCD_FBHEIGHT-1;
|
|
|
|
/* Copy specified rectange bitmap to hardware */
|
|
for (; y <= ymax; y++)
|
|
{
|
|
lcd_write_command(LCD_SET_PAGE | y );
|
|
lcd_write_command_e(LCD_SET_COLUMN | ((x >> 4) & 0xf), x & 0x0f);
|
|
lcd_write_data (&lcd_framebuffer[y][x], width);
|
|
}
|
|
|
|
}
|
|
|
|
/* Helper function. */
|
|
void lcd_mono_data(const unsigned char *data, int count);
|
|
|
|
/* Performance function that works with an external buffer
|
|
note that by and bheight are in 8-pixel units! */
|
|
void lcd_blit_mono(const unsigned char *data, int x, int by, int width,
|
|
int bheight, int stride)
|
|
{
|
|
while (bheight--)
|
|
{
|
|
lcd_write_command(LCD_SET_PAGE | (by & 0xf));
|
|
lcd_write_command_e(LCD_SET_COLUMN | ((x >> 4) & 0xf), x & 0xf);
|
|
|
|
lcd_mono_data(data, width);
|
|
data += stride;
|
|
by++;
|
|
}
|
|
}
|
|
|
|
/* Helper function for lcd_grey_phase_blit(). */
|
|
void lcd_grey_data(unsigned char *values, unsigned char *phases, int count);
|
|
|
|
/* Performance function that works with an external buffer
|
|
note that by and bheight are in 8-pixel units! */
|
|
void lcd_blit_grey_phase(unsigned char *values, unsigned char *phases,
|
|
int x, int by, int width, int bheight, int stride)
|
|
{
|
|
stride <<= 3; /* 8 pixels per block */
|
|
|
|
while (bheight--)
|
|
{
|
|
lcd_write_command(LCD_SET_PAGE | (by & 0xf));
|
|
lcd_write_command_e(LCD_SET_COLUMN | ((x >> 4) & 0xf), x & 0xf);
|
|
|
|
lcd_grey_data(values, phases, width);
|
|
values += stride;
|
|
phases += stride;
|
|
by++;
|
|
}
|
|
}
|
|
|