8632f955f4
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31274 a1c6a512-1295-4272-9138-f99709370657
416 lines
12 KiB
C
416 lines
12 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2011 by Amaury Pouly
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#include "config.h"
|
|
#include "system.h"
|
|
#include "sd.h"
|
|
#include "sdmmc.h"
|
|
#include "ssp-imx233.h"
|
|
#include "pinctrl-imx233.h"
|
|
#include "button-target.h"
|
|
#include "fat.h"
|
|
#include "disk.h"
|
|
#include "usb.h"
|
|
#include "debug.h"
|
|
|
|
/**
|
|
* This code assumes a single SD card slot
|
|
*/
|
|
|
|
#ifdef SANSA_FUZEPLUS
|
|
#define SD_SSP 1
|
|
#else
|
|
#error You need to configure the ssp to use
|
|
#endif
|
|
|
|
static tCardInfo card_info;
|
|
static long sd_stack [(DEFAULT_STACK_SIZE*2 + 0x200)/sizeof(long)];
|
|
static struct mutex sd_mutex;
|
|
static const char sd_thread_name[] = "sd";
|
|
static struct event_queue sd_queue;
|
|
static int sd_first_drive;
|
|
static int last_disk_activity;
|
|
|
|
static void sd_detect_callback(int ssp)
|
|
{
|
|
(void)ssp;
|
|
/* This is called only if the state was stable for 300ms - check state
|
|
* and post appropriate event. */
|
|
if(imx233_ssp_sdmmc_detect(SD_SSP))
|
|
queue_broadcast(SYS_HOTSWAP_INSERTED, 0);
|
|
else
|
|
queue_broadcast(SYS_HOTSWAP_EXTRACTED, 0);
|
|
imx233_ssp_sdmmc_setup_detect(SD_SSP, true, sd_detect_callback, false);
|
|
}
|
|
|
|
void sd_power(bool on)
|
|
{
|
|
#ifdef SANSA_FUZEPLUS
|
|
/* The Fuze+ uses pin B0P8 for whatever reason, power ? */
|
|
imx233_set_pin_function(0, 8, PINCTRL_FUNCTION_GPIO);
|
|
imx233_enable_gpio_output(0, 8, true);
|
|
imx233_set_gpio_output(0, 8, !on);
|
|
/* disable pull ups when not needed to save power */
|
|
imx233_ssp_setup_ssp1_sd_mmc_pins(on, 4, PINCTRL_DRIVE_4mA, false);
|
|
/* It also setups pin B1P30, unknown purpose */
|
|
imx233_set_pin_function(1, 30, PINCTRL_FUNCTION_GPIO);
|
|
imx233_enable_gpio_output(1, 30, false);
|
|
#endif
|
|
}
|
|
|
|
void sd_enable(bool on)
|
|
{
|
|
static int sd_enable = 2; /* 2 means not on and not off, for init purpose */
|
|
if(sd_enable == on)
|
|
return;
|
|
|
|
sd_enable = on;
|
|
}
|
|
|
|
#define MCI_NO_RESP 0
|
|
#define MCI_RESP (1<<0)
|
|
#define MCI_LONG_RESP (1<<1)
|
|
#define MCI_ACMD (1<<2)
|
|
#define MCI_NOCRC (1<<3)
|
|
#define MCI_BUSY (1<<4)
|
|
|
|
static bool send_cmd(uint8_t cmd, uint32_t arg, uint32_t flags, uint32_t *resp)
|
|
{
|
|
if((flags & MCI_ACMD) && !send_cmd(SD_APP_CMD, card_info.rca, MCI_RESP, resp))
|
|
return false;
|
|
|
|
enum imx233_ssp_resp_t resp_type = (flags & MCI_LONG_RESP) ? SSP_LONG_RESP :
|
|
(flags & MCI_RESP) ? SSP_SHORT_RESP : SSP_NO_RESP;
|
|
enum imx233_ssp_error_t ret = imx233_ssp_sd_mmc_transfer(SD_SSP, cmd, arg,
|
|
resp_type, NULL, 0, !!(flags & MCI_BUSY), false, resp);
|
|
if(resp_type == SSP_LONG_RESP)
|
|
{
|
|
/* Our SD codes assume most significant word first, so reverse resp */
|
|
uint32_t tmp = resp[0];
|
|
resp[0] = resp[3];
|
|
resp[3] = tmp;
|
|
tmp = resp[1];
|
|
resp[1] = resp[2];
|
|
resp[2] = tmp;
|
|
}
|
|
return ret == SSP_SUCCESS;
|
|
}
|
|
|
|
static int sd_wait_for_tran_state(void)
|
|
{
|
|
unsigned long response;
|
|
unsigned int timeout = current_tick + 5*HZ;
|
|
int cmd_retry = 10;
|
|
|
|
while (1)
|
|
{
|
|
while(!send_cmd(SD_SEND_STATUS, card_info.rca, SSP_SHORT_RESP, &response) && cmd_retry > 0)
|
|
cmd_retry--;
|
|
|
|
if(cmd_retry <= 0)
|
|
return -1;
|
|
|
|
if(((response >> 9) & 0xf) == SD_TRAN)
|
|
return 0;
|
|
|
|
if(TIME_AFTER(current_tick, timeout))
|
|
return -10 * ((response >> 9) & 0xf);
|
|
|
|
last_disk_activity = current_tick;
|
|
}
|
|
}
|
|
|
|
static int sd_init_card(void)
|
|
{
|
|
sd_enable(false);
|
|
sd_power(false);
|
|
sd_power(true);
|
|
sd_enable(true);
|
|
imx233_ssp_start(SD_SSP);
|
|
imx233_ssp_softreset(SD_SSP);
|
|
imx233_ssp_set_mode(SD_SSP, HW_SSP_CTRL1__SSP_MODE__SD_MMC);
|
|
/* SSPCLK @ 96MHz
|
|
* gives bitrate of 96000 / 240 / 1 = 400kHz */
|
|
imx233_ssp_set_timings(SD_SSP, 240, 0, 0xffff);
|
|
|
|
imx233_ssp_sd_mmc_power_up_sequence(SD_SSP);
|
|
imx233_ssp_set_bus_width(SD_SSP, 1);
|
|
imx233_ssp_set_block_size(SD_SSP, 9);
|
|
|
|
card_info.rca = 0;
|
|
bool sd_v2 = false;
|
|
uint32_t resp;
|
|
long init_timeout;
|
|
/* go to idle state */
|
|
if(!send_cmd(SD_GO_IDLE_STATE, 0, MCI_NO_RESP, NULL))
|
|
return -1;
|
|
/* CMD8 Check for v2 sd card. Must be sent before using ACMD41
|
|
Non v2 cards will not respond to this command */
|
|
if(send_cmd(SD_SEND_IF_COND, 0x1AA, MCI_RESP, &resp))
|
|
if((resp & 0xFFF) == 0x1AA)
|
|
sd_v2 = true;
|
|
/* timeout for initialization is 1sec, from SD Specification 2.00 */
|
|
init_timeout = current_tick + HZ;
|
|
do
|
|
{
|
|
/* this timeout is the only valid error for this loop*/
|
|
if(TIME_AFTER(current_tick, init_timeout))
|
|
return -2;
|
|
|
|
/* ACMD41 For v2 cards set HCS bit[30] & send host voltage range to all */
|
|
if(!send_cmd(SD_APP_OP_COND, (0x00FF8000 | (sd_v2 ? 1<<30 : 0)),
|
|
MCI_ACMD|MCI_NOCRC|MCI_RESP, &card_info.ocr))
|
|
return -100;
|
|
} while(!(card_info.ocr & (1<<31)));
|
|
|
|
/* CMD2 send CID */
|
|
if(!send_cmd(SD_ALL_SEND_CID, 0, MCI_RESP|MCI_LONG_RESP, card_info.cid))
|
|
return -3;
|
|
|
|
/* CMD3 send RCA */
|
|
if(!send_cmd(SD_SEND_RELATIVE_ADDR, 0, MCI_RESP, &card_info.rca))
|
|
return -4;
|
|
|
|
/* Try to switch V2 cards to HS timings, non HS seem to ignore this */
|
|
if(sd_v2)
|
|
{
|
|
/* CMD7 w/rca: Select card to put it in TRAN state */
|
|
if(!send_cmd(SD_SELECT_CARD, card_info.rca, MCI_RESP, NULL))
|
|
return -5;
|
|
|
|
if(sd_wait_for_tran_state())
|
|
return -6;
|
|
|
|
/* CMD6 */
|
|
if(!send_cmd(SD_SWITCH_FUNC, 0x80fffff1, MCI_NO_RESP, NULL))
|
|
return -7;
|
|
sleep(HZ/10);
|
|
|
|
/* go back to STBY state so we can read csd */
|
|
/* CMD7 w/rca=0: Deselect card to put it in STBY state */
|
|
if(!send_cmd(SD_DESELECT_CARD, 0, MCI_NO_RESP, NULL))
|
|
return -8;
|
|
}
|
|
|
|
/* CMD9 send CSD */
|
|
if(!send_cmd(SD_SEND_CSD, card_info.rca, MCI_RESP|MCI_LONG_RESP, card_info.csd))
|
|
return -9;
|
|
|
|
sd_parse_csd(&card_info);
|
|
|
|
/* SSPCLK @ 96MHz
|
|
* gives bitrate of 96 / 4 / 1 = 24MHz */
|
|
imx233_ssp_set_timings(SD_SSP, 4, 0, 0xffff);
|
|
|
|
/* CMD7 w/rca: Select card to put it in TRAN state */
|
|
if(!send_cmd(SD_SELECT_CARD, card_info.rca, MCI_RESP, &resp))
|
|
return -12;
|
|
if(sd_wait_for_tran_state() < 0)
|
|
return -13;
|
|
|
|
/* ACMD6: set bus width to 4-bit */
|
|
if(!send_cmd(SD_SET_BUS_WIDTH, 2, MCI_RESP|MCI_ACMD, &resp))
|
|
return -15;
|
|
/* ACMD42: disconnect the pull-up resistor on CD/DAT3 */
|
|
if(!send_cmd(SD_SET_CLR_CARD_DETECT, 0, MCI_RESP|MCI_ACMD, &resp))
|
|
return -17;
|
|
|
|
/* Switch to 4-bit */
|
|
imx233_ssp_set_bus_width(SD_SSP, 4);
|
|
|
|
card_info.initialized = 1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void sd_thread(void) NORETURN_ATTR;
|
|
static void sd_thread(void)
|
|
{
|
|
struct queue_event ev;
|
|
|
|
while (1)
|
|
{
|
|
queue_wait_w_tmo(&sd_queue, &ev, HZ);
|
|
|
|
switch(ev.id)
|
|
{
|
|
case SYS_HOTSWAP_INSERTED:
|
|
case SYS_HOTSWAP_EXTRACTED:
|
|
{
|
|
int microsd_init = 1;
|
|
fat_lock(); /* lock-out FAT activity first -
|
|
prevent deadlocking via disk_mount that
|
|
would cause a reverse-order attempt with
|
|
another thread */
|
|
mutex_lock(&sd_mutex); /* lock-out card activity - direct calls
|
|
into driver that bypass the fat cache */
|
|
|
|
/* We now have exclusive control of fat cache and sd */
|
|
|
|
disk_unmount(sd_first_drive); /* release "by force", ensure file
|
|
descriptors aren't leaked and any busy
|
|
ones are invalid if mounting */
|
|
/* Force card init for new card, re-init for re-inserted one or
|
|
* clear if the last attempt to init failed with an error. */
|
|
card_info.initialized = 0;
|
|
|
|
if(ev.id == SYS_HOTSWAP_INSERTED)
|
|
{
|
|
microsd_init = sd_init_card();
|
|
if(microsd_init < 0) /* initialisation failed */
|
|
panicf("microSD init failed : %d", microsd_init);
|
|
|
|
microsd_init = disk_mount(sd_first_drive); /* 0 if fail */
|
|
}
|
|
/*
|
|
* Mount succeeded, or this was an EXTRACTED event,
|
|
* in both cases notify the system about the changed filesystems
|
|
*/
|
|
if(microsd_init)
|
|
queue_broadcast(SYS_FS_CHANGED, 0);
|
|
|
|
sd_enable(false);
|
|
/* Access is now safe */
|
|
mutex_unlock(&sd_mutex);
|
|
fat_unlock();
|
|
break;
|
|
}
|
|
case SYS_TIMEOUT:
|
|
if(!TIME_BEFORE(current_tick, last_disk_activity+(3*HZ)))
|
|
sd_enable(false);
|
|
break;
|
|
case SYS_USB_CONNECTED:
|
|
usb_acknowledge(SYS_USB_CONNECTED_ACK);
|
|
/* Wait until the USB cable is extracted again */
|
|
usb_wait_for_disconnect(&sd_queue);
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
int sd_init(void)
|
|
{
|
|
mutex_init(&sd_mutex);
|
|
queue_init(&sd_queue, true);
|
|
create_thread(sd_thread, sd_stack, sizeof(sd_stack), 0,
|
|
sd_thread_name IF_PRIO(, PRIORITY_USER_INTERFACE) IF_COP(, CPU));
|
|
sd_enable(false);
|
|
imx233_ssp_sdmmc_setup_detect(SD_SSP, true, sd_detect_callback, false);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int transfer_sectors(IF_MD2(int drive,) unsigned long start, int count, void *buf, bool read)
|
|
{
|
|
IF_MD((void) drive);
|
|
int ret = 0;
|
|
uint32_t resp;
|
|
|
|
last_disk_activity = current_tick;
|
|
|
|
mutex_lock(&sd_mutex);
|
|
sd_enable(true);
|
|
|
|
if(card_info.initialized <= 0)
|
|
{
|
|
ret = sd_init_card();
|
|
if(card_info.initialized <= 0)
|
|
goto Lend;
|
|
}
|
|
|
|
if(!send_cmd(SD_SELECT_CARD, card_info.rca, SSP_NO_RESP, NULL))
|
|
{
|
|
ret = -20;
|
|
goto Lend;
|
|
}
|
|
ret = sd_wait_for_tran_state();
|
|
if(ret < 0)
|
|
goto Ldeselect;
|
|
while(count != 0)
|
|
{
|
|
int this_count = MIN(count, IMX233_MAX_SSP_XFER_SIZE / 512);
|
|
/* Set bank_start to the correct unit (blocks or bytes) */
|
|
int bank_start = start;
|
|
if(!(card_info.ocr & (1<<30))) /* not SDHC */
|
|
bank_start *= SD_BLOCK_SIZE;
|
|
ret = imx233_ssp_sd_mmc_transfer(SD_SSP, read ? SD_READ_MULTIPLE_BLOCK : SD_WRITE_MULTIPLE_BLOCK,
|
|
bank_start, SSP_SHORT_RESP, buf, this_count, false, read, &resp);
|
|
if(ret != SSP_SUCCESS)
|
|
break;
|
|
if(!send_cmd(SD_STOP_TRANSMISSION, 0, SSP_SHORT_RESP|MCI_BUSY, &resp))
|
|
{
|
|
ret = -15;
|
|
break;
|
|
}
|
|
count -= this_count;
|
|
start += this_count;
|
|
buf += this_count * 512;
|
|
}
|
|
|
|
Ldeselect:
|
|
/* CMD7 w/rca =0 : deselects card & puts it in STBY state */
|
|
if(!send_cmd(SD_DESELECT_CARD, 0, SSP_NO_RESP, NULL))
|
|
ret = -23;
|
|
Lend:
|
|
mutex_unlock(&sd_mutex);
|
|
return ret;
|
|
}
|
|
|
|
int sd_read_sectors(IF_MD2(int drive,) unsigned long start, int count,
|
|
void* buf)
|
|
{
|
|
return transfer_sectors(IF_MD2(drive,) start, count, buf, true);
|
|
}
|
|
|
|
int sd_write_sectors(IF_MD2(int drive,) unsigned long start, int count,
|
|
const void* buf)
|
|
{
|
|
return transfer_sectors(IF_MD2(drive,) start, count, (void *)buf, false);
|
|
}
|
|
|
|
tCardInfo *card_get_info_target(int card_no)
|
|
{
|
|
(void)card_no;
|
|
return &card_info;
|
|
}
|
|
|
|
int sd_num_drives(int first_drive)
|
|
{
|
|
sd_first_drive = first_drive;
|
|
return 1;
|
|
}
|
|
|
|
bool sd_present(IF_MD(int drive))
|
|
{
|
|
IF_MD((void) drive);
|
|
return imx233_ssp_sdmmc_detect(SD_SSP);
|
|
}
|
|
|
|
bool sd_removable(IF_MD(int drive))
|
|
{
|
|
IF_MD((void) drive);
|
|
return true;
|
|
}
|
|
|
|
long sd_last_disk_activity(void)
|
|
{
|
|
return last_disk_activity;
|
|
}
|
|
|