eefe273ce6
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@27148 a1c6a512-1295-4272-9138-f99709370657
144 lines
4.7 KiB
C
144 lines
4.7 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2009 by Bertrik Sikken
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#include "config.h"
|
|
#include <inttypes.h>
|
|
#include "as3525.h"
|
|
#include "dbop-as3525.h"
|
|
|
|
#if defined(SANSA_FUZE) || defined(SANSA_FUZEV2)
|
|
#define DBOP_PRECHARGE 0x80FF
|
|
#elif defined(SANSA_E200V2) || defined(SANSA_C200V2)
|
|
#define DBOP_PRECHARGE 0xF0FF
|
|
#endif
|
|
|
|
#if CONFIG_CPU == AS3525
|
|
/* doesn't work with the new ams sansas so far and is not needed */
|
|
static short int dbop_input_value = 0;
|
|
|
|
/* read the DBOP data pins */
|
|
unsigned short dbop_read_input(void)
|
|
{
|
|
unsigned int dbop_ctrl_old = DBOP_CTRL;
|
|
unsigned int dbop_timpol23_old = DBOP_TIMPOL_23;
|
|
|
|
/* make sure that the DBOP FIFO is empty */
|
|
while ((DBOP_STAT & (1<<10)) == 0);
|
|
|
|
int delay = 10;
|
|
while (delay--) asm volatile ("nop\n");
|
|
|
|
/* write DBOP_DOUT to pre-charge DBOP data lines with a defined level */
|
|
DBOP_TIMPOL_23 = 0xe007e007; /* no strobe towards lcd */
|
|
DBOP_CTRL = (1 << 19) | /* tri-state output */
|
|
(1 << 16) | /* enw=1 (enable write) */
|
|
(1 << 12); /* ow=1 (16-bit data width) */
|
|
DBOP_DOUT = DBOP_PRECHARGE;
|
|
#if defined(SANSA_C200V2)
|
|
/* two additional writes to precharge longer get rid of the read noise */
|
|
DBOP_DOUT = DBOP_PRECHARGE;
|
|
DBOP_DOUT = DBOP_PRECHARGE;
|
|
#endif
|
|
while ((DBOP_STAT & (1<<10)) == 0);
|
|
|
|
#if defined(SANSA_FUZE) || defined(SANSA_E200V2)
|
|
delay = 50;
|
|
while (delay--) asm volatile ("nop\n");
|
|
#endif
|
|
|
|
/* perform a DBOP read */
|
|
DBOP_CTRL = (1 << 19) | /* tri-state output */
|
|
(1 << 15) | /* strd=1 (start read) */
|
|
(1 << 12) | /* ow=1 (16-bit data width) */
|
|
(31 << 0); /* rs_t=31 (read DBOP at end of cycle) */
|
|
while ((DBOP_STAT & (1<<16)) == 0);
|
|
dbop_input_value = DBOP_DIN;
|
|
|
|
/* restore previous values */
|
|
DBOP_TIMPOL_23 = dbop_timpol23_old;
|
|
DBOP_CTRL = dbop_ctrl_old;
|
|
|
|
return dbop_input_value;
|
|
}
|
|
|
|
/* for the debug menu */
|
|
unsigned short dbop_debug(void)
|
|
{
|
|
return dbop_input_value;
|
|
}
|
|
|
|
#endif
|
|
|
|
static inline void dbop_set_mode(int mode)
|
|
{
|
|
int delay = 10;
|
|
unsigned long ctrl = DBOP_CTRL;
|
|
int curr_mode = (DBOP_CTRL >> 13) & 0x3; // bits 14:13
|
|
#ifdef SANSA_FUZEV2
|
|
if (mode == 32 && curr_mode != 1<<1)
|
|
DBOP_CTRL = (ctrl & ~(1<<13)) | (1<<14); // 2 serial half words
|
|
else if (mode == 16 && curr_mode != 1<<0)
|
|
DBOP_CTRL = (ctrl & ~(1<<14)) | (1<<13); // 2 serial bytes
|
|
#else
|
|
if (mode == 32 && curr_mode == 0)
|
|
DBOP_CTRL = ctrl | (1<<13|1<<14); /* 2 serial half words */
|
|
else if (mode == 16 && curr_mode == (1<<1|1<<0))
|
|
DBOP_CTRL = ctrl & ~(1<<14|1<<13); /* 1 serial half word */
|
|
#endif
|
|
else
|
|
return;
|
|
while(delay--) asm volatile("nop");
|
|
}
|
|
|
|
void dbop_write_data(const int16_t* p_bytes, int count)
|
|
{
|
|
|
|
const int32_t *data;
|
|
if ((intptr_t)p_bytes & 0x3 || count == 1)
|
|
{ /* need to do a single 16bit write beforehand if the address is
|
|
* not word aligned or count is 1, switch to 16bit mode if needed */
|
|
dbop_set_mode(16);
|
|
DBOP_DOUT16 = *p_bytes++;
|
|
if (!(--count))
|
|
return;
|
|
}
|
|
/* from here, 32bit transfers are save
|
|
* set it to transfer 4*(outputwidth) units at a time,
|
|
* if bit 12 is set it only does 2 halfwords though (we never set it)
|
|
* switch to 32bit output if needed */
|
|
dbop_set_mode(32);
|
|
data = (int32_t*)p_bytes;
|
|
while (count > 1)
|
|
{
|
|
DBOP_DOUT32 = *data++;
|
|
count -= 2;
|
|
|
|
/* Wait if push fifo is full */
|
|
while ((DBOP_STAT & (1<<6)) != 0);
|
|
}
|
|
/* While push fifo is not empty */
|
|
while ((DBOP_STAT & (1<<10)) == 0);
|
|
|
|
/* due to the 32bit alignment requirement or uneven count,
|
|
* we possibly need to do a 16bit transfer at the end also */
|
|
if (count > 0)
|
|
dbop_write_data((int16_t*)data, 1);
|
|
}
|