e286b0bbc0
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@27188 a1c6a512-1295-4272-9138-f99709370657
123 lines
4.3 KiB
C
123 lines
4.3 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
* Physical interface of the SI4700 in the Gigabeat S
|
|
*
|
|
* Copyright (C) 2008 by Nils Wallménius
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#include "config.h"
|
|
#include "system.h"
|
|
#include "mc13783.h"
|
|
#include "iomuxc-imx31.h"
|
|
#include "i2c-imx31.h"
|
|
#include "fmradio_i2c.h"
|
|
|
|
static struct i2c_node si4700_i2c_node =
|
|
{
|
|
.num = I2C2_NUM,
|
|
.ifdr = I2C_IFDR_DIV192, /* 66MHz/.4MHz = 165, closest = 192 = 343750Hz */
|
|
/* Just hard-code for now - scaling may require
|
|
* updating */
|
|
.addr = (0x20),
|
|
};
|
|
|
|
void fmradio_i2c_init(void)
|
|
{
|
|
/* RST: LOW */
|
|
bitclr32(&GPIO1_DR, (1 << 26));
|
|
/* RST: OUT */
|
|
bitset32(&GPIO1_GDIR, (1 << 26));
|
|
|
|
/* I2C2 SCL: IN, I2C2: SDA IN */
|
|
bitclr32(&GPIO2_GDIR, (3 << 14));
|
|
/* I2C2 SCL LO, I2C2 SDA LO */
|
|
bitclr32(&GPIO2_DR, (3 << 14));
|
|
|
|
/* open-drain pins - external pullups on PCB. Pullup default but
|
|
* disabled */
|
|
/* RI_DTE1 (I2C2_SCLK) */
|
|
iomuxc_set_pad_config(IOMUXC_RI_DTE1,
|
|
IOMUXC_PAD_PUE_PKE_DISABLE | IOMUXC_PAD_PUS_UP_100K |
|
|
IOMUXC_PAD_HYS | IOMUXC_PAD_ODE);
|
|
/* DCD_DTE1 (I2C2_SDA) */
|
|
iomuxc_set_pad_config(IOMUXC_DCD_DTE1,
|
|
IOMUXC_PAD_PUE_PKE_DISABLE | IOMUXC_PAD_PUS_UP_100K |
|
|
IOMUXC_PAD_HYS | IOMUXC_PAD_ODE);
|
|
|
|
/* set outputs to I2C2 */
|
|
/* RI_DTE1 => I2C2_SCLK */
|
|
iomuxc_set_pin_mux(IOMUXC_RI_DTE1,
|
|
IOMUXC_MUX_OUT_ALT2 | IOMUXC_MUX_IN_ALT2);
|
|
/* DCD_DTE1 => I2C2_SDA */
|
|
iomuxc_set_pin_mux(IOMUXC_DCD_DTE1,
|
|
IOMUXC_MUX_OUT_ALT2 | IOMUXC_MUX_IN_ALT2);
|
|
}
|
|
|
|
void fmradio_i2c_enable(bool enable)
|
|
{
|
|
if (enable)
|
|
{
|
|
/* place in GPIO mode to hold SDIO low during RESET release,
|
|
* SEN1 should be high already (pullup) and GPIO3 left alone */
|
|
bitset32(&GPIO2_GDIR, (1 << 15)); /* SDIO OUT */
|
|
/* I2C2_SDA => MCU2_15 */
|
|
iomuxc_set_pin_mux(IOMUXC_DCD_DTE1,
|
|
IOMUXC_MUX_OUT_GPIO | IOMUXC_MUX_IN_GPIO);
|
|
/* enable CLK32KMCU clock */
|
|
mc13783_set(MC13783_POWER_CONTROL0, MC13783_CLK32KMCUEN);
|
|
/* enable the fm chip (release RESET) */
|
|
bitset32(&GPIO1_DR, (1 << 26));
|
|
sleep(HZ/100);
|
|
/* busmode should be selected - OK to release SDIO */
|
|
bitclr32(&GPIO2_GDIR, (1 << 15)); /* SDIO IN */
|
|
/* restore pin mux (MCU2_15 => I2C2_SDA) */
|
|
iomuxc_set_pin_mux(IOMUXC_DCD_DTE1,
|
|
IOMUXC_MUX_OUT_ALT2 | IOMUXC_MUX_IN_ALT2);
|
|
/* the si4700 is the only thing connected to i2c2 so
|
|
we can diable the i2c module when not in use */
|
|
i2c_enable_node(&si4700_i2c_node, true);
|
|
}
|
|
else
|
|
{
|
|
/* the si4700 is the only thing connected to i2c2 so
|
|
we can diable the i2c module when not in use */
|
|
i2c_enable_node(&si4700_i2c_node, false);
|
|
/* disable the fm chip */
|
|
bitclr32(&GPIO1_DR, (1 << 26));
|
|
/* disable CLK32KMCU clock */
|
|
mc13783_clear(MC13783_POWER_CONTROL0, MC13783_CLK32KMCUEN);
|
|
}
|
|
}
|
|
|
|
int fmradio_i2c_write(unsigned char address, const unsigned char* buf, int count)
|
|
{
|
|
(void)address;
|
|
i2c_write(&si4700_i2c_node, buf, count);
|
|
return 0;
|
|
}
|
|
|
|
int fmradio_i2c_read(unsigned char address, unsigned char* buf, int count)
|
|
{
|
|
(void)address;
|
|
i2c_read(&si4700_i2c_node, -1, buf, count);
|
|
return 0;
|
|
}
|
|
|
|
int si4700_st(void)
|
|
{
|
|
return (GPIO1_DR & (1 << 28)) >> 28;
|
|
}
|