3f17745930
Do not rely on a bootloader initializing the HW, RB initializes and configures GPIO, I2C, and PMU at startup. Change-Id: If7f856b1f345f63de584aa4e4fc22d130cd66c80
88 lines
3 KiB
C
88 lines
3 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id: pmu-target.h 24721 2010-02-17 15:54:48Z theseven $
|
|
*
|
|
* Copyright © 2009 Michael Sparmann
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __PMU_TARGET_H__
|
|
#define __PMU_TARGET_H__
|
|
|
|
#include <stdbool.h>
|
|
#include "config.h"
|
|
|
|
#include "pcf5063x.h"
|
|
|
|
/* undocummented PMU registers */
|
|
#define PCF50635_REG_INT6 0x85
|
|
#define PCF50635_REG_INT6M 0x86
|
|
#define PCF50635_REG_GPIOSTAT 0x87 /* bit1: GPIO2 status (TBC) */
|
|
|
|
/* LDOs */
|
|
#define LDO_UNK1 1 /* TBC: SoC voltage (USB) */
|
|
#define LDO_UNK2 2 /* TBC: SoC voltage (I/O) */
|
|
#define LDO_LCD 3
|
|
#define LDO_CODEC 4
|
|
#define LDO_UNK5 5 /* TBC: nano3g NAND */
|
|
#define LDO_CWHEEL 6
|
|
#define LDO_ACCY 7 /* HCLDO */
|
|
/*
|
|
* Other LDOs:
|
|
* AUTOLDO: Hard Disk
|
|
* DOWN1: CPU
|
|
* DOWN2: SDRAM
|
|
* MEMLDO: SDRAM self-refresh (TBC)
|
|
*
|
|
* EXTON inputs:
|
|
* EXTON1: button/holdswitch related (TBC)
|
|
* EXTON2: USB Vbus (High when present)
|
|
* EXTON3: ACCESSORY (Low when present)
|
|
*
|
|
* PMU GPIO:
|
|
* GPIO1: input, Mikey (jack remote ctrl) interrupt (TBC)
|
|
* GPIO2: input, hold switch (TBC)
|
|
* GPIO3: output, unknown
|
|
*/
|
|
|
|
|
|
unsigned char pmu_read(int address);
|
|
int pmu_write(int address, unsigned char val);
|
|
int pmu_read_multiple(int address, int count, unsigned char* buffer);
|
|
int pmu_write_multiple(int address, int count, unsigned char* buffer);
|
|
int pmu_read_adc(unsigned int adc);
|
|
int pmu_read_battery_voltage(void);
|
|
int pmu_read_battery_current(void);
|
|
void pmu_init(void);
|
|
void pmu_ldo_on_in_standby(unsigned int ldo, int onoff);
|
|
void pmu_ldo_set_voltage(unsigned int ldo, unsigned char voltage);
|
|
void pmu_ldo_power_on(unsigned int ldo);
|
|
void pmu_ldo_power_off(unsigned int ldo);
|
|
void pmu_set_wake_condition(unsigned char condition);
|
|
void pmu_enter_standby(void);
|
|
void pmu_read_rtc(unsigned char* buffer);
|
|
void pmu_write_rtc(unsigned char* buffer);
|
|
void pmu_hdd_power(bool on);
|
|
|
|
void pmu_preinit(void);
|
|
#ifdef BOOTLOADER
|
|
unsigned char pmu_rd(int address);
|
|
int pmu_wr(int address, unsigned char val);
|
|
int pmu_rd_multiple(int address, int count, unsigned char* buffer);
|
|
int pmu_wr_multiple(int address, int count, unsigned char* buffer);
|
|
#endif
|
|
|
|
#endif /* __PMU_TARGET_H__ */
|