0f3987ce7f
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@14479 a1c6a512-1295-4272-9138-f99709370657
135 lines
3.9 KiB
C
135 lines
3.9 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2007 by Barry Wardell
|
|
*
|
|
* Based on code from the Linux Target Image Builder from Freescale
|
|
* available at http://www.bitshrine.org/ and
|
|
* http://www.bitshrine.org/gpp/linux-2.6.16-mx31-usb-2.patch
|
|
* Adapted for Rockbox in January 2007
|
|
* Original file: drivers/usb/gadget/arcotg_udc.c
|
|
*
|
|
* USB Device Controller Driver
|
|
* Driver for ARC OTG USB module in the i.MX31 platform, etc.
|
|
*
|
|
* Copyright 2004-2006 Freescale Semiconductor, Inc. All Rights Reserved.
|
|
*
|
|
* Based on mpc-udc.h
|
|
* Author: Li Yang (leoli@freescale.com)
|
|
* Jiang Bo (Tanya.jiang@freescale.com)
|
|
*
|
|
* All files in this archive are subject to the GNU General Public License.
|
|
* See the file COPYING in the source tree root for full license agreement.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#include "arcotg_udc.h"
|
|
#include "logf.h"
|
|
|
|
static int timeout;
|
|
|
|
/* @qh_addr is the aligned virt addr of ep QH addr
|
|
* it is used to set endpointlistaddr Reg */
|
|
/* was static int dr_controller_setup(void *qh_addr) */
|
|
int dr_controller_setup(void)
|
|
{
|
|
#if 0
|
|
struct arc_usb_config *config;
|
|
|
|
config = udc_controller->config;
|
|
|
|
/* before here, make sure usb_slave_regs has been initialized */
|
|
if (!qh_addr)
|
|
return -EINVAL;
|
|
#endif
|
|
|
|
/* Stop and reset the usb controller */
|
|
UDC_USBCMD &= ~USB_CMD_RUN_STOP;
|
|
|
|
UDC_USBCMD |= USB_CMD_CTRL_RESET;
|
|
|
|
/* Wait for reset to complete */
|
|
timeout = 10000000;
|
|
while ((UDC_USBCMD & USB_CMD_CTRL_RESET) &&
|
|
--timeout) {
|
|
continue;
|
|
}
|
|
if (timeout == 0) {
|
|
logf("%s: TIMEOUT", __FUNCTION__);
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
/* Set the controller as device mode and disable setup lockout */
|
|
UDC_USBMODE |= (USB_MODE_CTRL_MODE_DEVICE | USB_MODE_SETUP_LOCK_OFF);
|
|
|
|
/* Clear the setup status */
|
|
UDC_USBSTS = 0;
|
|
#if 0
|
|
UDC_ENDPOINTLISTADDR = (unsigned int)qh_addr & USB_EP_LIST_ADDRESS_MASK;
|
|
|
|
VDBG("qh_addr=0x%x epla_reg=0x%8x", qh_addr, UOG_ASYNCLISTADDR);
|
|
#endif
|
|
UDC_PORTSC1 = (UDC_PORTSC1 & ~PORTSCX_PHY_TYPE_SEL) | PORTSCX_PTS_UTMI;
|
|
#if 0
|
|
if (config->set_vbus_power)
|
|
config->set_vbus_power(0);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* just Enable DR irq reg and Set Dr controller Run */
|
|
/* was static void dr_controller_run(struct arcotg_udc *udc) */
|
|
void dr_controller_run(void)
|
|
{
|
|
/*Enable DR irq reg */
|
|
UDC_USBINTR = USB_INTR_INT_EN | USB_INTR_ERR_INT_EN |
|
|
USB_INTR_PTC_DETECT_EN | USB_INTR_RESET_EN |
|
|
USB_INTR_DEVICE_SUSPEND | USB_INTR_SYS_ERR_EN;
|
|
#if 0
|
|
/* Clear stopped bit */
|
|
udc->stopped = 0;
|
|
#endif
|
|
/* Set the controller as device mode */
|
|
UDC_USBMODE |= USB_MODE_CTRL_MODE_DEVICE;
|
|
|
|
/* Set controller to Run */
|
|
UDC_USBCMD |= USB_CMD_RUN_STOP;
|
|
|
|
return;
|
|
}
|
|
|
|
/* just Enable DR irq reg and Set Dr controller Run */
|
|
/* was static void dr_controller_stop(struct arcotg_udc *udc) */
|
|
void dr_controller_stop(void)
|
|
{
|
|
#if 0
|
|
/* if we're in OTG mode, and the Host is currently using the port,
|
|
* stop now and don't rip the controller out from under the
|
|
* ehci driver
|
|
*/
|
|
if (udc->gadget.is_otg) {
|
|
if (!(UDC_OTGSC & OTGSC_STS_USB_ID)) {
|
|
logf("Leaving early");
|
|
return;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
/* disable all INTR */
|
|
UDC_USBINTR = 0;
|
|
#if 0
|
|
/* Set stopped bit */
|
|
udc->stopped = 1;
|
|
#endif
|
|
/* Set controller to Stop */
|
|
UDC_USBCMD &= ~USB_CMD_RUN_STOP;
|
|
}
|