Nyaaori/rockbox
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
rockbox/rbutil/mkamsboot/dualboot/dualboot.S
Rafaël Carré c23a7ccbbc Fuzev2: use enrd0 for USB detection, GPIO didn't work on some models 
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26125 a1c6a512-1295-4272-9138-f99709370657
2010-05-18 00:11:42 +00:00

380 lines
11 KiB
ArmAsm
Raw Blame History

/***************************************************************************
* __________ __ ___.
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
* \/ \/ \/ \/ \/
* $Id$
*
* Copyright (C) 2008 Rafaël Carré
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
*
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
* KIND, either express or implied.
*
****************************************************************************/
.text
/* AS3525 hardware registers */
.set GPIOA, 0xC80B0000
.set GPIOB, 0xC80C0000
.set GPIOC, 0xC80D0000
.set GPIOD, 0xC80E0000
.set CGU_PROC, 0xC80F0010
.set CGU_PERI, 0xC80F0014
.set I2C_BASE, 0xC8070000
.set I2C_DATA, 0x00
.set I2C_SLAD0, 0x04
.set I2C_CNTRL, 0x0c
.set I2C_DACNT, 0x10
.set I2C_CPSR0, 0x1c
.set I2C_CPSR1, 0x20
.set I2C_IMR, 0x24
.set I2C_SR, 0x30
.set I2C_SADDR, 0x44
.set AS3514_I2C_ADDR, 0x46
.set AS3514_IRQ_ENRD0, 0x25
.set PCLK, 24000000
.set I2C_CLK, 400000
.set I2C_PRESCALER, ((PCLK + I2C_CLK -1) / I2C_CLK)
.set I2C_PRESCALER_LOW, (I2C_PRESCALER & 0xff)
.set I2C_PRESCALER_HIGH, (I2C_PRESCALER >> 8)
#if I2C_PRESCALER_HIGH > 3
#error i2c prescaler too big!
#endif
/* Vectors */
ldr pc, =start /* reset vector */
/* next vectors are unused, halt cpu */
1: b 1b
1: b 1b
1: b 1b
1: b 1b
1: b 1b
1: b 1b
1: b 1b
/* These values are filled in by mkamsboot - don't move them from offset 0x20 */
uclunpack_end: .word 0 /* End of the ucl_unpack function */
uclunpack_size: .word 0 /* Size in bytes of the ucl_unpack function */
ucl_of_end: .word 0 /* End of the ucl-compressed OF image */
ucl_of_size: .word 0 /* Size in bytes of the compressed OF image */
ucl_rb_end: .word 0 /* End of the ucl-compressed RB image */
ucl_rb_size: .word 0 /* Size in bytes of the compressed RB image */
ucl_dest: .word 0 /* End of our destination buffer (end of memory) */
start:
/* First copy the UCL unpack function to the end of RAM */
ldr r0, uclunpack_end /* Source */
ldr r1, uclunpack_size /* Source length */
sub r2, r0, r1 /* Source start - 1*/
ldr r3, ucl_dest /* Destination end */
uclcopy:
ldrb r4, [r0], #-1
strb r4, [r3], #-1
cmp r2, r0
bne uclcopy
/* store the new destination buffer */
str r3, ucl_dest
/* enable gpio clock */
ldr r0, =CGU_PERI
ldr r1, [r0]
orr r1, r1, #(1<<16)
str r1, [r0]
/* TODO : M200V4 ? */
#if defined(SANSA_CLIP) || defined(SANSA_CLIPV2)
#define USB_PIN 6
#elif defined(SANSA_FUZE) || defined(SANSA_E200V2)
#define USB_PIN 3
#endif
#ifdef USB_PIN /* TODO : remove this check when we'll have an USB driver */
ldr r0, =GPIOA
mov r1, #0
str r1, [r0, #0x400]
ldr r1, [r0, #(4*(1<<USB_PIN))]
cmp r1, #0
bne boot_of
#endif
#if defined(SANSA_C200V2)
/* Instead of checking the GPIO, check the audio master IRQ_ENRD0
* USB_STATUS bit on C200V2 */
ldr r0, =CGU_PERI
ldr r1, [r0]
/* enable i2c audio master clock */
orr r1, r1, #(1<<17)
/* make sure 24MHz clk_main is selected */
bic r1, r1, #0x7f
str r1, [r0]
ldr r0, =I2C_BASE
/* disable i2c interrupts */
mov r1, #0
str r1, [r0, #I2C_IMR]
/* setup prescaler */
mov r1, #I2C_PRESCALER_LOW
str r1, [r0, #I2C_CPSR0]
mov r1, #I2C_PRESCALER_HIGH
str r1, [r0, #I2C_CPSR1]
/* setup i2c slave address */
mov r1, #(AS3514_I2C_ADDR << 1)
str r1, [r0, #I2C_SLAD0]
mov r2, #0x51
str r2, [r0, #I2C_CNTRL]
/* wait for not busy */
1:
ldr r1, [r0, #I2C_SR]
tst r1, #1
bne 1b
/* start read of irq_enrd0 */
mov r1, #AS3514_IRQ_ENRD0
str r1, [r0, #I2C_SADDR]
orr r2, r2, #(1 << 1)
str r2, [r0, #I2C_CNTRL]
mov r1, #1
str r1, [r0, #I2C_DACNT]
/* wait for transfer to finish */
1:
ldr r1, [r0, #I2C_DACNT]
cmp r1, #0
bne 1b
/* load result and test USB_STATUS bit */
ldr r1, [r0, #I2C_DATA]
tst r1, #(1 << 3)
bne boot_of
#endif
/* Here are model specific tests, for dual boot without a computer */
/* All models use left button */
/* /!\ Right button for c200v2 (left button is unkwown) */
#ifdef SANSA_CLIP
.set row, (1<<5) /* enable output on C5 */
.set col, (1<<0) /* read keyscan column B0 */
ldr r0, =GPIOC
mov r1, #row
str r1, [r0, #0x400]
str r1, [r0, #(4*row)]
ldr r0, =GPIOB
mov r1, #0
str r1, [r0, #0x400]
ldr r1, [r0, #(4*col)]
cmp r1, #0
bne boot_of
#elif defined(SANSA_CLIPV2)
.set row, (1<<4) /* enable output on D4 */
.set col, (1<<0) /* read keyscan column D0 */
ldr r0, =GPIOD
mov r1, #((1<<5)|(1<<4)|(1<<3)) /* all rows as output */
str r1, [r0, #0x400]
/* all rows high */
mov r1, #(1<<3)
str r1, [r0, #(4*(1<<3))]
mov r1, #(1<<4)
str r1, [r0, #(4*(1<<4))]
mov r1, #(1<<5)
str r1, [r0, #(4*(1<<5))]
mov r1, #0 /* button row low */
str r1, [r0, #(4*row)]
mov r1, #5 /* small delay */
1: subs r1, r1, #1
bne 1b
ldr r1, [r0, #(4*col)]
cmp r1, #0
beq boot_of
#elif defined(SANSA_E200V2) || defined(SANSA_FUZE)
ldr r0, =GPIOC
mov r1, #0
str r1, [r0, #0x400]
ldr r1, [r0, #0x20] /* read pin C3 */
cmp r1, #0 /* C3 = #0 means button pressed */
beq boot_of
#elif defined(SANSA_FUZEV2)
ldr r0, =GPIOC
mov r1, #0
str r1, [r0, #0x400]
ldr r1, [r0, #0x20] /* read pin C3 */
cmp r1, #0 /* C3 != #0 means button pressed */
bne boot_of
#elif defined(SANSA_CLIPPLUS)
@ read pins
ldr r0, =GPIOC
ldr r1, [r0, #4*(1<<3)] @ read pin C3 "|<<"
ldr r0, =GPIOA
ldr r2, [r0, #4*(1<<1)] @ read pin A1 "Home"
orr r2, r2, r1 @ c3 || A1
cmp r2, #0 @ test input from pins
bne boot_of @ branch directly to OF if either pin high
#elif defined(SANSA_C200V2)
/* check for RIGHT on C6, should changed to LEFT as soon as it
* known in which pin that is in order for consistency */
ldr r0, =GPIOC
mov r1, #0
str r1, [r0, #0x400] /* set pin to output */
ldr r1, [r0, #256] /* 1<<(6+2) */
cmp r1, #0 /* C6 low means button pressed */
beq boot_of
#elif defined(SANSA_M200V4)
.set row, (1<<5) /* enable output on A5 */
.set col, (1<<0) /* read keyscan column A0 */
ldr r0, =GPIOA
mov r1, #row
str r1, [r0, #0x400]
str r1, [r0, #(4*row)]
ldr r2, [r0, #(4*col)]
/* check value read (1 means button pressed) */
cmp r2, #0
bne boot_of
#else
#error No target-specific key check defined!
#endif
#if defined(SANSA_CLIPPLUS) || defined(SANSA_FUZEV2)
/* Check for USB after buttons because I trust more the GPIO code than
* the i2c code.
* Also it seems we need to wait a bit before detecting USB connection
* on those models, but not on c200v2
*/
ldr r0, =CGU_PROC
mov r1, #0
str r1, [r0] @ fclk = 24MHz
ldr r0, =CGU_PERI
ldr r1, [r0]
/* enable i2c audio master clock */
orr r1, r1, #(1<<17)
/* pclk = fclk = 24MHz */
bic r1, r1, #0x7f
str r1, [r0]
ldr r0, =I2C_BASE
/* disable i2c interrupts */
mov r1, #0
str r1, [r0, #I2C_IMR]
/* setup prescaler */
mov r1, #I2C_PRESCALER_LOW
str r1, [r0, #I2C_CPSR0]
mov r1, #I2C_PRESCALER_HIGH
str r1, [r0, #I2C_CPSR1]
/* setup i2c slave address */
mov r1, #(AS3514_I2C_ADDR << 1)
str r1, [r0, #I2C_SLAD0]
mov r2, #0x51
str r2, [r0, #I2C_CNTRL]
/* wait for not busy */
1:
ldr r1, [r0, #I2C_SR]
tst r1, #1
bne 1b
/* wait a bit (~100ms) else detection fails */
mov r1, #0x80000
1: subs r1, r1, #1
bne 1b
/* start read of irq_enrd0 */
mov r1, #AS3514_IRQ_ENRD0
str r1, [r0, #I2C_SADDR]
orr r2, r2, #(1 << 1)
str r2, [r0, #I2C_CNTRL]
mov r1, #1
str r1, [r0, #I2C_DACNT]
/* wait for transfer to finish */
1:
ldr r1, [r0, #I2C_DACNT]
cmp r1, #0
bne 1b
/* load result and test USB_STATUS bit */
ldr r1, [r0, #I2C_DATA]
tst r1, #(1 << 3)
bne boot_of
#endif
/* The dualboot button was not held, so we boot rockbox */
ldr r0, ucl_rb_end /* Address of compressed image */
ldr r1, ucl_rb_size /* Compressed size */
b decompress
boot_of:
ldr r0, ucl_of_end /* Address of compressed image */
ldr r1, ucl_of_size /* Compressed size */
decompress:
/* At this point: */
/* r0 = source_end for UCL image to copy */
/* r1 = size of UCL image to copy */
ldr r3, ucl_dest
add r5, r3, #2 /* r5 is entry point of copy of uclunpack */
/* function, plus one (for thumb mode */
sub r4, r3, r1 /* r4 := destination_start - 1 */
fw_copy:
ldrb r2, [r0], #-1
strb r2, [r3], #-1
cmp r3, r4 /* Stop when we reached dest_start-1 */
bne fw_copy
/* Call the ucl decompress function, which will branch to 0x0 */
/* on completion */
add r0, r3, #1 /* r0 := Start of compressed image */
/* r1 already contains compressed size */
mov r2, #0 /* r2 := Destination for unpacking */
bx r5 /* Branch to uclunpack, switching to thumb */
/* never reached : uclunpack will branch to the reset vector (0x0) */
Reference in a new issue View git blame Copy permalink