This allows the user to make use of the DAC's power-saving abilities.
The two modes are "high performance" and "battery saver". This feature
is supported by the AK4376 DAC in the upcoming FiiO M3K port.
The setting is only a manual toggle right now, but in the future it
could be hooked up to the battery level (via another setting) so it
can be toggled automatically when the battery gets too low.
Change-Id: I482af6e2f969fcbdeb3411bd3ff91f866b12d027
The Q and K have a slightly different case, but the hardware under the
shell is completely identical.
These models are rebadged versions:
* Hifiwalker H2 (== Q)
* AGPTek H3 (== K)
* Surfans F20 (== K)
Other notes:
* Significant improvements in the shared Hiby-platform launcher/loader
* SD card can theoretically be hot-swapped now
* Support external USB mass storage!
* Some consolidation of Hiby-platform targets
* Some consolidation of plugin keymaps
Todo/known issues:
* Keymaps need to be gone over properly
* Convert to HAVE_SCROLLWHEEL?
Change-Id: I5a8a4f22c38a5b69392ca7c0a8ad8c4e07d9523c
Most credit goes to: Roman Skylarov
Additional integration and refactoring by myself.
*** COMPLETELY UNTESTED ***
Change-Id: Ia64c36d92e0214c6b15f7a868df286f8113ea27b
* xduoo x3ii/x20: Better line out support
* less granular volume settings (too many steps before)
* Better handling of swiching sample rates
* Log actual sample rate in debug menu
Most credit goes to Roman Stolyarov
Additional integration [re]work by myself
Change-Id: I63af3740678cf2ed3170f61534e1029c81826bb6
Provided by Roman Stolyarov
Integration, Refactoring, and Upstreaming by Solomon Peachy
X3II confirmed working by forum tester, X20 is nearly identical.
This includes bootloader, main firmware, and the flash image patcher.
Eventual Todo:
* Further refactor AGPTek Rocker & xduoo hiby bootloaders
* Further refactor AGPTek Rocker & xduoo hosted platform code
Change-Id: I34a674051d368efcc75d1d18c725971fe46c3eee
Cleaned up, rebased, and forward-ported from the xvortex fork.
(original credit to vsoftster@gmail.com)
Change-Id: Ibcc023a0271ea81e901450a88317708c2683236d
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
SUPPORTED SERIES:
- NWZ-E450
- NWZ-E460
- NWZ-E470
- NWZ-E580
- NWZ-A10
NOTES:
- bootloader makefile convert an extra font to be installed alongside the bootloader
since sysfont is way too small
- the toolsicon bitmap comes from the Oxygen iconset
- touchscreen driver is untested
TODO:
- implement audio routing driver (pcm is handled by pcm-alsa)
- fix playback: it crashes on illegal instruction in DEBUG builds
- find out why the browser starts at / instead of /contents
- implement radio support
- implement return to OF for usb handling
- calibrate battery curve (NB: of can report a battery level on a 0-5 scale but
probabl don't want to use that ?)
- implement simulator build (we need a nice image of the player)
- figure out if we can detect jack removal
POTENTIAL TODOS:
- try to build a usb serial gadget and gdbserver
Change-Id: Ic77d71e0651355d47cc4e423a40fb64a60c69a80
Everytime I use it, I get highly confused because it's complicated and
undocumented. The code is spread all over the place and some targets clearly
use incorrect values. This is the first step of a series to cleanup audio settings
and document it properly.
Change-Id: I20cb7af2bfa33986cb8b0bf8573f17a92227f893
Reorganization
- Separated iBasso devices from PLATFORM_ANDROID. These are now standlone
hosted targets. Most device specific code is in the
firmware/target/hosted/ibasso directory.
- No dependency on Android SDK, only the Android NDK is needed.
32 bit Android NDK and Android API Level 16.
- Separate implementation for each device where feasible.
Code cleanup
- Rewrite of existing code, from simple reformat to complete reimplementation.
- New backlight interface, seperating backlight from touchscreen.
- Rewrite of device button handler, removing unneeded code and fixing memory
leaks.
- New Debug messages interface logging to Android adb logcat (DEBUGF, panicf,
logf).
- Rewrite of lcd device handler, removing unneeded code and fixing memory leaks.
- Rewrite of audiohw device handler/pcm interface, removing unneeded code and
fixing memory leaks, enabling 44.1/48kHz pthreaded playback.
- Rewrite of power and powermng, proper shutdown, using batterylog results
(see http://gerrit.rockbox.org/r/#/c/1047/).
- Rewrite of configure (Android NDK) and device specific config.
- Rewrite of the Android NDK specific Makefile.
Misc
- All plugins/games/demos activated.
- Update tinyalsa to latest from https://github.com/tinyalsa/tinyalsa.
Includes
- http://gerrit.rockbox.org/r/#/c/993/
- http://gerrit.rockbox.org/r/#/c/1010/
- http://gerrit.rockbox.org/r/#/c/1035/
Does not include http://gerrit.rockbox.org/r/#/c/1007/ due to new backlight
interface and new option for hold switch, touchscreen, physical button
interaction.
Rockbox needs the iBasso DX50/DX90 loader for startup, see
http://gerrit.rockbox.org/r/#/c/1099/
The loader expects Rockbox to be installed in /mnt/sdcard/.rockbox/. If
/mnt/sdcard/ is accessed as USB mass storage device, Rockbox will exit
gracefully and the loader will restart Rockbox on USB disconnect.
Tested on iBasso DX50.
Compiled (not tested) for iBasso DX90.
Compiled (not tested) for PLATFORM_ANDROID.
Change-Id: I5f5e22e68f5b4cf29c28e2b40b2c265f2beb7ab7
HiFi E.T. MA8 is almost the same as MA9 except
another DAC(pcm1792 in ma8, df1704 in ma9).
MA8 has ILI9342 lcd, MA8C has ILI9342C lcd.
Change-Id: If2ac04f5a3382590b2a392c46286559f54b2ed6a
HAVE_SW_VOLUME_CONTROL is required and at this time only affects the
SDL targets using pcm-sdl.c.
Enables balance control in SDL targets, unless mono volume is in use.
Compiles software volume control as unbuffered when
PCM_SW_VOLUME_UNBUFFERED is defined. This avoids the overhead and
extra latency introduced by the double buffer when it is not needed.
Use this config when the target's PCM driver is buffered and sufficient
latency exists to perform safely the volume scaling.
Simulated targets that are double-buffered when made as native targets
remain so in the sim in order to run the same code.
Change-Id: Ifa77d2d3ae7376c65afecdfc785a084478cb5ffb
Reviewed-on: http://gerrit.rockbox.org/457
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
If AUDIOHW_CAPS is defined without explicit BASS_CAP/TREBLE_CAP while
HAVE_SW_TONE_CONTROLS is defined, AUDIOHW_HAVE_BASS/TREBLE should be
defined or otherwise the tone controls won't show up. TREBLE/BASS were
being defined if AUDIOHW_CAPS was NOT defined, but the same rule should
apply if the codec needs to specify other caps but doesn't use hardware
tone controls.
(I'm surprised noone noticed some settings gone missing :-)
Change-Id: I85b5c467bab07bb62362a0dc2d582267ac2d8ec9
* SOUND_x enum can be generated by audiohw_settings.h along with settings
entries and sound_val2phys.
* VOLUME_MIN and VOLUME_MAX are no longer necessary within sound.c. If
you need them, they are for target-defined purposes.
* Fix up SDL volume implementation in sdl.c. Move sim volume calculation
code to pcm-sdl.c.
* Min trigger tresholds were based upon VOLUME_MIN for some reason.
These setting have nothing to do with playback volume. Since it is no
longer present, set these at -89dB which is the minimum peak meter
sensitivity setting.
* Fix an oversight in wm8758.c. I forgot to add the dB->register
conversion to audiohw_set_volume.
Change-Id: Ie1df33f1793eee75e6793f16bc7bddd16edb7f75
This is going right in since it's long overdue. If anything is goofed,
drop me a line or just tweak it yourself if you know what's wrong. :-)
Make HW/SW codec interface more uniform when emulating HW functionality
on SWCODEC for functions such as "audiohw_set_pitch". The firmware-to-
DSP plumbing is in firmware/drivers/audiohw-swcodec.c. "sound_XXX"
APIs are all in sound.c with none in DSP code any longer.
Reduce number of settings definitions needed by each codec by providing
defaults for common ones like balance, channels and SW tone controls.
Remove need for separate SIM code and tables and add virtual codec header
for hosted targets.
Change-Id: I3f23702bca054fc9bda40f49824ce681bb7f777b
This port is a hybrid native/RaaA port. It runs on a embedded linux system,
but is the only application. It therefore can implement lots of stuff that
native targets also implement, while leveraging the underlying linux kernel.
The port is quite advanced. User interface, audio playback, plugins work
mostly fine. Missing is e.g. power mangement and USB (see SamsungYPR0 wiki page).
Included in utils/ypr0tools are scripts and programs required to generate
a patched firmware. The patched firmware has the rootfs modified to load
Rockbox. It includes a early/safe USB mode.
This port needs a new toolchain, one that includes glibc headers and libraries.
rockboxdev.sh can generate it, but e.g. codesourcey and distro packages may
also work.
Most of the initial effort is done by Lorenzo Miori and others (on ABI),
including reverse engineering and patching of the original firmware,
initial drivers, and more. Big thanks to you.
Flyspray: FS#12348
Author: Lorenzo Miori, myself
Merry christmas to ypr0 owners! :)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31415 a1c6a512-1295-4272-9138-f99709370657
Included are drivers for buttons, backlight, lcd, audio and storage.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31000 a1c6a512-1295-4272-9138-f99709370657
Major known issues:
- No bootloader yet
- No support for the first-generation 160GB CE-ATA hard disk drive yet
- Audio playback is slow, only FLAC seems to reach realtime
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@28953 a1c6a512-1295-4272-9138-f99709370657
General state is: Rockbox is usable (plays music, saves configuration, touchscreen works too).
Problems:
- Playing music in the background (i.e. when switching to another app) doesn't work reliably, but I'm working on that now.
- no cabbiev2 (only some preliminary files for it), no other default theme.
- screen flickers sometimes if the updates are too frequent
- no multi screen apk/package
- strange behavior when a phone call comes in
The java files (and the eclipse project) resides in android/, which is also supposed to be the build folder.
I've put a small README in there for instructions. There are some steps needed after the make part, which are described there,
and which eclipse mostly handles. But there ought to be some script/makefile rules which do that instead in the future.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@27668 a1c6a512-1295-4272-9138-f99709370657
It still works mostly like the simulator. There's also some minor left overs from the sim, but it does not define SIMULATOR.
It installs into the current (build) dir, and you need to run it with '--root .' (because it looks for ./.rockbox and not ./simdisk/rockbox) as options. That's one of the few kludges left that should be resolved soon'ish.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@27310 a1c6a512-1295-4272-9138-f99709370657
- Refactor the program startup. main() is now in main.c like on target, and the implicit application thread will now act as our main thread (previously a separate one was created for this in thread initialization).
This is part of Rockbox as an application and is the first step to make an application port from the uisimulator. In a further step the sim bits from the sdl build will be separated out.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26065 a1c6a512-1295-4272-9138-f99709370657
Remove audiohw_mute from header as well, and make this function static
to each driver (commented out when it was unused)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25733 a1c6a512-1295-4272-9138-f99709370657