NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
The STMP3700 has unreliable vbusvalid irq so we need to use
vdd5gtvddio. Therefore, using the vbusvalid bit produces
inconsistent results between events and detect. Fix that
by making power handle all the usb detect stuff.
Change-Id: Ic521b2f6677602e184fe46352c5359f4b4ba8d56
There are many small differences between them. In particular
some regulators are not available on stmp3600. Also the vbusvalid
detect method is not available as an irq on stmp3600 and seems
broken on stmp3700. Finally die temperature is handled by the
power block on stmp3600.
Change-Id: I2c68b418738f15564e445d3a1496018cef97fff7
Do low level power init in system_init(). This can be needed
since imx233 must be able to frequecy scale atfer system_init()
and kernel_init() and this is only possible if power system was
initialised.
Change-Id: I27c66ec0dccd60bda26a45be24683c0bfe72c6da
Make sure DCDC is running at boot (it is disabled by default when
5V is present and we don't want to rely on the bootloader to
change this).
When changing the voltage on a regulator, it usually takes 2ms for
the voltage to stabilize. In DCDC mode, there is an irq to notify
about the event so use it ! This is especially important when
changing cpu frequency because increasing the cpu freq while the
voltage is rising is unreliable.
Change-Id: Icfe9ef3ee90156d1e17da0820d9041859f7f3bca
Remove the old debug stuff about VDDx and add a clean api to
get/set the regulator (VDDD, VDDA, VDDIO, VDDMEM). This is useful
for proper frequency scaling.
Change-Id: Ia5a1a712fd66652a8ad9601ed00db31aba5a7561
- now identity map dram uncached and have a cached and buffered virtual alias
- rework dma to handle virtual to physical pointers conversion
- fix lcd frame pointer
- implement usb detection properly
- implement bootloader usb properly
- allow the bootloader to disable MMC windowing (useful for recovery)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30432 a1c6a512-1295-4272-9138-f99709370657
