This will help debugging, and can be disabled for releases if needed
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31226 a1c6a512-1295-4272-9138-f99709370657
Fix problems with volume of recorded material by converting 14-bit samples to
16-bit. Remove duplicate samples from recorded data and support proper
samplerate since ADC runs 1/2 the codec clock. Support monitoring mono on both
output channels by feeding data manually to I2SOUT under the right conditions.
DMA is no longer used for recording since frames must be processed as described
above but it does allow full-duplex audio.
Miscellaneous change includes a proper constant (HW_SAMPR_DEFAULT) to reset the
hardware samplerate when recording is closed. PP5024 and AS3525 have different
default recording rates (22kHz and 44kHz respectively) but both have half-speed
ADC.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31180 a1c6a512-1295-4272-9138-f99709370657
AMS*: define CURRENT_MAX_CHG to give more correct estimation of recharge time
The amount of current each target draws from the charger is defined in
powermgmt-target.h
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@27994 a1c6a512-1295-4272-9138-f99709370657
Gets a bit more battery life
Adjust current usage, it was a bit too low for Clipv2/Clip+
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26866 a1c6a512-1295-4272-9138-f99709370657
A specific poweroff function needs to be used for wake-up to work
Disable RTC in bootloaders for consistency with other Sansas
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26243 a1c6a512-1295-4272-9138-f99709370657
build it on fuzev2 and clipv2 too, it should be the same controller
as3525v1 file is only build for CONFIG_USBOTG == USBOTG_AS3525, no need
to check for it in the .c file
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26142 a1c6a512-1295-4272-9138-f99709370657
also remove an obsolete comment and an unrelated option of the config file
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26000 a1c6a512-1295-4272-9138-f99709370657
When the rest of the code is confirmed to work properly without CPU
frequency changes, it will be possible to reliabily test set_cpu_frequency()
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25924 a1c6a512-1295-4272-9138-f99709370657
Instead of modifying CGU_PROC to get 24MHz pclk, just switch to fastbus else Clip+ wouldn't boot
Tested on fuzev1/Clip+
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25413 a1c6a512-1295-4272-9138-f99709370657
Add HAVE_AS3543 config define to differentiate the bits changed since as3514/as3517
Enable recording on Fuzev2/Clipv2/Clip+, although it was tested on Clip+ only
Note: storage is still read-only so I tested by listening to headphones loopback and watching the recording level in recscreen
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25390 a1c6a512-1295-4272-9138-f99709370657
CGU_PROC looks different from as3525v1 and there have been reports of
Clip+ becoming warm when boosted
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25020 a1c6a512-1295-4272-9138-f99709370657
Reuse some code from Clip (LCD) and a lot of code from AS3525
Add a new CPU type : AS3525v2, identical to AS3525 except it's an ARMv5 (arm926-ejs)
SD code still not working
For an unknown reason LCD doesn't work anymore (to be investigated)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24131 a1c6a512-1295-4272-9138-f99709370657
