Turn on 4x oversampling inside UDA1380 codec.
This allow will move the quantization noise to the higher frequencies,
that slightly improve the final sound quality.
Change-Id: Idf79cd877c526d8937a47c34e9c180d837a15db1
Reviewed-on: http://gerrit.rockbox.org/435
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
Reviewed-by: Björn Stenberg <bjorn@haxx.se>
No code changed, just shuffling stuff around. This should make it easier to
build only select parts kernel and use different implementations.
Change-Id: Ie1f00f93008833ce38419d760afd70062c5e22b5
This is the basic port to the new target Samsung
YP-R1, which runs on a similar platform as YP-R0.
Port is usable, although there are still
some optimizations that have to be done.
Change-Id: If83a8e386369e413581753780c159026d9e41f04
HiFi E.T. MA8 is almost the same as MA9 except
another DAC(pcm1792 in ma8, df1704 in ma9).
MA8 has ILI9342 lcd, MA8C has ILI9342C lcd.
Change-Id: If2ac04f5a3382590b2a392c46286559f54b2ed6a
Using a better resolution causes havoc in the user interface
because it doesn't properly handle steps and people start to
believe I am responsible for all this mess.
Change-Id: I02b68dce5802692efde3da226eeeb49e4995f97a
If target has HW tone controls but no HW prescaler (non-implemented or
non-existent), audiohw_set_prescaler() should, for now, do nothing.
Change-Id: If1b1a36970dca82fda1c350fbaa4d6ce068a6d32
Conversion from centibels to register values was left out of
audiohw_set_lineout_volume().
Credit goes to Dave Marsh for providing the fix.
Just another little oversight from sound/audiohw rework.
Change-Id: I7f8b1c5fb575ac95b5d595c2f4824fbb5ebbd3c8
Just one more SNAFU after redoing sound.c. Software bass/treble controls
in the DSP expect .1 dB gain increments but the gains were being set as
1 dB increments because that's what the AUDIOHW_SETTING specifies. Just
x10 the gains given to audiohw_set_bass/treble.
Change-Id: Id5296f93908ec0036a5605d3a60a2cb5eec91bb5
HAVE_SW_VOLUME_CONTROL is required and at this time only affects the
SDL targets using pcm-sdl.c.
Enables balance control in SDL targets, unless mono volume is in use.
Compiles software volume control as unbuffered when
PCM_SW_VOLUME_UNBUFFERED is defined. This avoids the overhead and
extra latency introduced by the double buffer when it is not needed.
Use this config when the target's PCM driver is buffered and sufficient
latency exists to perform safely the volume scaling.
Simulated targets that are double-buffered when made as native targets
remain so in the sim in order to run the same code.
Change-Id: Ifa77d2d3ae7376c65afecdfc785a084478cb5ffb
Reviewed-on: http://gerrit.rockbox.org/457
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
* SOUND_x enum can be generated by audiohw_settings.h along with settings
entries and sound_val2phys.
* VOLUME_MIN and VOLUME_MAX are no longer necessary within sound.c. If
you need them, they are for target-defined purposes.
* Fix up SDL volume implementation in sdl.c. Move sim volume calculation
code to pcm-sdl.c.
* Min trigger tresholds were based upon VOLUME_MIN for some reason.
These setting have nothing to do with playback volume. Since it is no
longer present, set these at -89dB which is the minimum peak meter
sensitivity setting.
* Fix an oversight in wm8758.c. I forgot to add the dB->register
conversion to audiohw_set_volume.
Change-Id: Ie1df33f1793eee75e6793f16bc7bddd16edb7f75
This is going right in since it's long overdue. If anything is goofed,
drop me a line or just tweak it yourself if you know what's wrong. :-)
Make HW/SW codec interface more uniform when emulating HW functionality
on SWCODEC for functions such as "audiohw_set_pitch". The firmware-to-
DSP plumbing is in firmware/drivers/audiohw-swcodec.c. "sound_XXX"
APIs are all in sound.c with none in DSP code any longer.
Reduce number of settings definitions needed by each codec by providing
defaults for common ones like balance, channels and SW tone controls.
Remove need for separate SIM code and tables and add virtual codec header
for hosted targets.
Change-Id: I3f23702bca054fc9bda40f49824ce681bb7f777b
Onda VX747 sim was missing a limits #define; #include limits.h in
pcm_sw_volume.h.
Simply use the software volume control for the SIM volume control
rather than the SDL volume control when the target would have it
natively.
Change-Id: I8e924a2ff1b410f602452d2ea9b691efb82c931e
Basically it uses the default SI4700 radio chip driver, the only thing that's different is the I2C access,
written specifically to interact with my kernel module.
Next things to add are:
- RDS support!
Change-Id: I0ed125641e00f93124d7a34f90dd508e7f1db5a4
Signed-off-by: Lorenzo Miori <memorys60@gmail.com>
The headphone volume register value reads differently in Line1 and DAC mode.
Since the volume is not set again when switching between playback and radio,
we need to remember the hp volume and reapply setting when changing the mode.
Change-Id: I8fbd344f78653c19d81a39dd3f680ec6885cb1ec
Use two stage amplification (PGA gain and digital stage gain)
combined to extend recgain range to -17.25 +60.0dB.
Change-Id: I4df8af801730b7efb2d35096de077ba31d331222
move prototypes to ascodec.h
move code to ascodec*.c
YPR0: use adc-as3514.c instead of duplicating it
TODO: merge as3514.h and ascodec.h ?
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31626 a1c6a512-1295-4272-9138-f99709370657
* Introduce CONFIG_BATTERY_MEASURE define, to allow targets (application)
to break powermgmt.c's assumption about the ability to read battery voltage.
There's now additionally percentage (android) and remaining time measure
(maemo). No measure at all also works (sdl app). If voltage can't be measured,
then battery_level() is king and it'll be used for power_history and runtime
estimation.
* Implement target's API in the simulator, i.e. _battery_voltage(), so it
doesn't need to implement it's own powermgmt.c and other stubs. Now
the sim behaves much more like a native target, although it still
changes the simulated battery voltage quickly,
* Other changes include include renaming battery_adc_voltage() to
_battery_voltage(), for consistency with the new target functions and
making some of the apps code aware that voltage and runtime estimation
is not always available.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31548 a1c6a512-1295-4272-9138-f99709370657
It's now using completely the same driver as Sansa daps.
This also increases the volume range.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31428 a1c6a512-1295-4272-9138-f99709370657
This port is a hybrid native/RaaA port. It runs on a embedded linux system,
but is the only application. It therefore can implement lots of stuff that
native targets also implement, while leveraging the underlying linux kernel.
The port is quite advanced. User interface, audio playback, plugins work
mostly fine. Missing is e.g. power mangement and USB (see SamsungYPR0 wiki page).
Included in utils/ypr0tools are scripts and programs required to generate
a patched firmware. The patched firmware has the rootfs modified to load
Rockbox. It includes a early/safe USB mode.
This port needs a new toolchain, one that includes glibc headers and libraries.
rockboxdev.sh can generate it, but e.g. codesourcey and distro packages may
also work.
Most of the initial effort is done by Lorenzo Miori and others (on ABI),
including reverse engineering and patching of the original firmware,
initial drivers, and more. Big thanks to you.
Flyspray: FS#12348
Author: Lorenzo Miori, myself
Merry christmas to ypr0 owners! :)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31415 a1c6a512-1295-4272-9138-f99709370657
