A GNU extension that returns dst + size instead of dst. It's a nice
shortcut when copying strings with a known size or back-to-back blocks
and you have to do it often.
May of course be called directly or alternately through
__builtin_mempcpy in some compiler versions.
For ASM on native targets, it is implemented as an alternate entrypoint
to memcpy which adds minimal code and overhead.
Change-Id: I4cbb3483f6df3c1007247fe0a95fd7078737462b
This patch redoes the filesystem code from the FAT driver up to the
clipboard code in onplay.c.
Not every aspect of this is finished therefore it is still "WIP". I
don't wish to do too much at once (haha!). What is left to do is get
dircache back in the sim and find an implementation for the dircache
indicies in the tagcache and playlist code or do something else that
has the same benefit. Leaving these out for now does not make anything
unusable. All the basics are done.
Phone app code should probably get vetted (and app path handling
just plain rewritten as environment expansions); the SDL app and
Android run well.
Main things addressed:
1) Thread safety: There is none right now in the trunk code. Most of
what currently works is luck when multiple threads are involved or
multiple descriptors to the same file are open.
2) POSIX compliance: Many of the functions behave nothing like their
counterparts on a host system. This leads to inconsistent code or very
different behavior from native to hosted. One huge offender was
rename(). Going point by point would fill a book.
3) Actual running RAM usage: Many targets will use less RAM and less
stack space (some more RAM because I upped the number of cache buffers
for large memory). There's very little memory lying fallow in rarely-used
areas (see 'Key core changes' below). Also, all targets may open the same
number of directory streams whereas before those with less than 8MB RAM
were limited to 8, not 12 implying those targets will save slightly
less.
4) Performance: The test_disk plugin shows markedly improved performance,
particularly in the area of (uncached) directory scanning, due partly to
more optimal directory reading and to a better sector cache algorithm.
Uncached times tend to be better while there is a bit of a slowdown in
dircache due to it being a bit heavier of an implementation. It's not
noticeable by a human as far as I can say.
Key core changes:
1) Files and directories share core code and data structures.
2) The filesystem code knows which descriptors refer to same file.
This ensures that changes from one stream are appropriately reflected
in every open descriptor for that file (fileobj_mgr.c).
3) File and directory cache buffers are borrowed from the main sector
cache. This means that when they are not in use by a file, they are not
wasted, but used for the cache. Most of the time, only a few of them
are needed. It also means that adding more file and directory handles
is less expensive. All one must do in ensure a large enough cache to
borrow from.
4) Relative path components are supported and the namespace is unified.
It does not support full relative paths to an implied current directory;
what is does support is use of "." and "..". Adding the former would
not be very difficult. The namespace is unified in the sense that
volumes may be specified several times along with relative parts, e.g.:
"/<0>/foo/../../<1>/bar" :<=> "/<1>/bar".
5) Stack usage is down due to sharing of data, static allocation and
less duplication of strings on the stack. This requires more
serialization than I would like but since the number of threads is
limited to a low number, the tradoff in favor of the stack seems
reasonable.
6) Separates and heirarchicalizes (sic) the SIM and APP filesystem
code. SIM path and volume handling is just like the target. Some
aspects of the APP file code get more straightforward (e.g. no path
hashing is needed).
Dircache:
Deserves its own section. Dircache is new but pays homage to the old.
The old one was not compatible and so it, since it got redone, does
all the stuff it always should have done such as:
1) It may be update and used at any time during the build process.
No longer has one to wait for it to finish building to do basic file
management (create, remove, rename, etc.).
2) It does not need to be either fully scanned or completely disabled;
it can be incomplete (i.e. overfilled, missing paths), still be
of benefit and be correct.
3) Handles mounting and dismounting of individual volumes which means
a full rebuild is not needed just because you pop a new SD card in the
slot. Now, because it reuses its freed entry data, may rebuild only
that volume.
4) Much more fundamental to the file code. When it is built, it is
the keeper of the master file list whether enabled or not ("disabled"
is just a state of the cache). Its must always to ready to be started
and bind all streams opened prior to being enabled.
5) Maintains any short filenames in OEM format which means that it does
not need to be rebuilt when changing the default codepage.
Miscellaneous Compatibility:
1) Update any other code that would otherwise not work such as the
hotswap mounting code in various card drivers.
2) File management: Clipboard needed updating because of the behavioral
changes. Still needs a little more work on some finer points.
3) Remove now-obsolete functionality such as the mutex's "no preempt"
flag (which was only for the prior FAT driver).
4) struct dirinfo uses time_t rather than raw FAT directory entry
time fields. I plan to follow up on genericizing everything there
(i.e. no FAT attributes).
5) unicode.c needed some redoing so that the file code does not try
try to load codepages during a scan, which is actually a problem with
the current code. The default codepage, if any is required, is now
kept in RAM separarately (bufalloced) from codepages specified to
iso_decode() (which must not be bufalloced because the conversion
may be done by playback threads).
Brings with it some additional reusable core code:
1) Revised file functions: Reusable code that does things such as
safe path concatenation and parsing without buffer limitations or
data duplication. Variants that copy or alter the input path may be
based off these.
To do:
1) Put dircache functionality back in the sim. Treating it internally
as a different kind of file system seems the best approach at this
time.
2) Restore use of dircache indexes in the playlist and database or
something effectively the same. Since the cache doesn't have to be
complete in order to be used, not getting a hit on the cache doesn't
unambiguously say if the path exists or not.
Change-Id: Ia30f3082a136253e3a0eae0784e3091d138915c8
Reviewed-on: http://gerrit.rockbox.org/566
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
After a local commit, any file that included version.h would have to
be recompiled on account of the changed version string. This changes
version.h in the build directory to rbversion.h and includes the
preprocessor macro from rbversion.h in firmware/common/version.c so
that only that one file needs to be recompiled after a local commit
rather than a whole slew of them.
Change-Id: I900d97e3a24a0610698283416d97b4fa3a3a2cf6
Reviewed-on: http://gerrit.rockbox.org/937
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
We redefine the top-level macros to our own in order to maintain
compatibility with compound initializers by wrapping the mid or low
level definitions from the OS header.
This allows, hopefully optimized, macros from the host OS's headers to
be used when building any hosted target obviating the need for
NEED_GENERIC_BYTESWAPS unless the target simply doesn't define its
own optimized versions (MIPS!).
Throw in some 64-bit swaps for completeness' sake; they generate no code
if not yet used anyway.
Change-Id: I21b384b55fea46833d01ea3cad1ad8952ea01a11
The changed thread code may not wish to save the old context under
certain circumstances but thread-unix.c assumed it would, cached it
and used it unconditionally.
Also, prevent it from leaking away all the jump buffers (old problem).
Creating and removing threads would eventually run it out of buffers
and then it would crash after that. Plugins, like Pictureflow, which
have worker threads could only be started a few times. Implement a
simple O(1) allocator that will reuse them and stays self-contained
to its own types (as it appears the original author intended).
Change-Id: Icf65413c086b346fb79bf827102b725269e2812c
Nice colorful diffs reveals some lines that should NOT have been
removed when !defined(HAVE_PRIORITY_SCHEDULING) in mutex_unlock.
Change-Id: I4152ea864b7706217c670e1b99250b09e69c5858
Forgot to (void) an unused parameter when priorityless.
usb-drv-rl27xx.c was using a compound init to initialize a semaphore
but the structure changed so that it is no longer correct. Use
designated initializers to avoid having to complete all fields.
Forgot to break compatibility on all plugins and codecs since the
kernel objects are now different. Take care of that too and do the
sort thing.
Change-Id: Ie2ab8da152d40be0c69dc573ced8d697d94b0674
Abstracts threading from itself a bit, changes the way its queues are
handled and does type hiding for that as well.
Do alot here due to already required major brain surgery.
Threads may now be on a run queue and a wait queue simultaneously so
that the expired timer only has to wake the thread but not remove it
from the wait queue which simplifies the implicit wake handling.
List formats change for wait queues-- doubly-linked, not circular.
Timeout queue is now singly-linked. The run queue is still circular
as before.
Adds a better thread slot allocator that may keep the slot marked as
used regardless of the thread state. Assists in dumping special tasks
that switch_thread was tasked to perform (blocking tasks).
Deletes alot of code yet surprisingly, gets larger than expected.
Well, I'm not not minding that for the time being-- omlettes and break
a few eggs and all that.
Change-Id: I0834d7bb16b2aecb2f63b58886eeda6ae4f29d59
Forms implemented to a greater or lesser degree at the moment:
ll_* = singly-linked list
lld_* = doubly-linked list
lldc_* = doubly-linked circular list
Change-Id: Ieed5af50fc59165c8b14c3513b3b5d0e6f7de9fa
* HWCODEC bootloaders
* Remove references to thread structures outside the kernel. They are
private and should not be used elsewhere. The mrobe-100 is an offender
that gets squashed.
* The ata.c hack stuff for large sector disks on iPod Video gets squashed
for the same reason. I will no longer maintain it, period; please find
the real reason for its difficulties.
Change-Id: Iae1a675beac887754eb3cc59b560c941077523f5
* Seal away private thread and kernel definitions and declarations
into the internal headers in order to better hide internal structure.
* Add a thread-common.c file that keeps shared functions together.
List functions aren't messed with since that's about to be changed to
different ones.
* It is necessary to modify some ARM/PP stuff since GCC was complaining
about constant pool distance and I would rather not force dump it. Just
bl the cache calls in the startup and exit code and let it use veneers
if it must.
* Clean up redundant #includes in relevant areas and reorganize them.
* Expunge useless and dangerous stuff like remove_thread().
Change-Id: I6e22932fad61a9fac30fd1363c071074ee7ab382
thread_queue_wake() doesn't need the 2nd parameter. The original purpose
for it never came to be.
Non priority version mrsw_writer_wakeup_readers was left improperly
finished. Get that back into line.
Change-Id: Ic613a2479f3cc14dc7c761517670eb15178da9f5
find_first_set_bit() becomes a small inline on ARMv5+ and checkwps now gets
made with -std=gnu99 (it eats all the GCCOPTS) like the rest of things.
Change-Id: Ie6039b17fec057a3dcb0f453d8fd5efac984df89
Any number of readers may be in the critical section at a time and writers
are mutually exclusive to all other threads. They are a better choice when
data is rarely modified but often read and multiple threads can safely
access it for reading.
Priority inheritance is fully implemented along with other changes to the
kernel to fully support it on multiowner objects.
This also cleans up priority code in the kernel and updates some associated
structures in existing objects to the cleaner form.
Currently doesn't add the mrsw_lock.[ch] files since they're not yet
needed by anything but the supporting improvements are still useful.
This includes a typed bitarray API (bitarray.h) which is pretty basic
for now.
Change-Id: Idbe43dcd9170358e06d48d00f1c69728ff45b0e3
Reviewed-on: http://gerrit.rockbox.org/801
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
Remote buttons are bound to the standard buttons in button-target.h, but they can
have a separate buttonmap, if someone wants.
Change-Id: Id8c78a3dfec0005bf588dc16416870b4c7c56836
OF doesn't do such thing. Values in mV are converted proportionally, so no change
to the battery meter.
Change-Id: Ic545b0514535e7f17f0379ed02f6bdf515f69ac6
The "percent_to_volt_charge" values are quite arbitrary
and may need some more tweaking.
Change-Id: I9f177d46681030d615fe2c2e78cf9bd2dde026af
Reviewed-on: http://gerrit.rockbox.org/824
Reviewed-by: Szymon Dziok <b0hoon@o2.pl>
Tested: Szymon Dziok <b0hoon@o2.pl>
This doesn't touch external tools as I see no need for.
Change-Id: Ia69248c4b6a033c3772916525257e3540bddcffa
Reviewed-on: http://gerrit.rockbox.org/891
Tested: Sebastian Leonhardt <sebastian.leonhardt@web.de>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
crc32gentab() which initilizes crc table was called in bootloader
but not in main binary. Fix this temporary by always calling it in
load_mi4(). The proper fix probably to switch to const table and
drop runtime initialization.
Change-Id: I8b0c2c791642f56ed56189d156647661935a815d
Apparently the backlight driver is leaking current even when the PWM set to 0.
This patch should greatly improve the battery life of the device.
Change-Id: I76bbc8a87cae452e599b37de17e91f373cee58bc
On those targets, since the LCDIF cannot recover from underflow, changing the
EMI frequency kills one frame and cause flicker.
Change-Id: Id3c130636bcfddcc6c54896602699fbaa1636ab4
* e200v2 shouldn't use 24bit (was just for testing)
* samsung ypr0/ypr1 should enable it but the correct number must be passed to bmp2rb
Change-Id: Ia91b0ff80a54265d4c3111d9dcb8e7b9dd12b5d4
With LCD driver all calculation will be performed on RGB888 and the hardware/OS
can display from our 24bit framebuffer.
It is not yet as performance optimized as the existing drivers but should be
good enough.The vast number of small changes is due to the fact that
fb_data can be a struct type now, while most of the code expected a scalar type.
lcd-as-memframe ASM code does not work with 24bit currently so the with 24bit
it enforces the generic C code.
All plugins are ported over. Except for rockpaint. It uses so much memory that
it wouldnt fit into the 512k plugin buffer anymore (patches welcome).
Change-Id: Ibb1964545028ce0d8ff9833ccc3ab66be3ee0754
An upcoming lcd-24bit.c driver will re-use a lot of code from the 16bit
drivers, so prepare for that.
Change-Id: I7bc7f6b992e5e3f4e0a0aa54dc08103ebb05315f
There is no simple method to detect radio through the 3-wire interface, so it's
not implemented for the YH-925 for now. YH-920 always has a radio.
Change-Id: Iea484d752915fcd40dbbbd7dbbf13e81aaf548db
Because of architecture of the codec it's always necessary to route the input
signal from ADC to DAC, in order to have a control over the monitoring volume
and in order to hear anything while recording.
Change-Id: I1089894c949ab7371857d74aedb6bdf5a7d39c41
Although both players basically have the same keys, the
differences in the layout is rather big, so I think both
deserve their own keymaps.
(On the yh820 the FFWD/PLAY/REW buttons are located above the
direction keys, on the yh920 at the side of the player.
Furthermore the yh920/925 has a REC switch, whereas
yh820 has a push button.)
Change-Id: I0e62a1b101c387646c0bdb07ea142d9d2430ca15
Reviewed-on: http://gerrit.rockbox.org/814
Reviewed-by: Szymon Dziok <b0hoon@o2.pl>
The lcd driver now works but is awfully slow. The trick is to put it in system
mode instead of RGB and setup 16bpp. The GRAM data can then be sent directly
with the SPI but since it's bit-banged and the CPU running at slow speed,
full screen refresh takes over a second, even with a slightly optmised version.
The OF uses a DMA mechanism with a proper LCD controller but the setup is much
more complicated and doesn't work at the moment.
Change-Id: I6c95d91de31bff97d0a5848b8e2078c21deb5895
errno is supposed to be thread local and we do that here in a rather
makeshift way by implementing a function that returns a pointer to
the __errno variable in the thread block.
If more serious TLS is required, perhaps it would be worthwhile
implementing it using the linker and the "__thread" storage attribute.
That's a bit overkill just for this. I'm also not liking what I saw
the compiler producing.
Change-Id: I03bc0bd6a89f6e3d6bae7653284ee01054614f9a
Reviewed-on: http://gerrit.rockbox.org/803
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
The write buffer should not be modified but the current code does and then
forget to restore it to its original content. I'm not sure if any code relies
to the write buffer to not be modifies by the write function but this seems like
a reasonable assumption in general so it's better not to break it.
Change-Id: I449a01db2ec51d2273e59b69c59db0e7d2eed3db
Scrollstrip works as quadrature encoder. We set pin change
interrupt for both edges of signal both lines and sample the state
in ISR. From time to time the sequence is out-of-sync which was
properly detected but erroneously handled leaving scrollstip
interrupts disabled.
Change-Id: I08e4f99c6c27df0f8180aa16e6e1d9e4203bafa7
Reviewed-on: http://gerrit.rockbox.org/782
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
Tested: Marcin Bukat <marcin.bukat@gmail.com>
This patch completes the plugin keymaps for the Zen X-Fi3 and enables those plugins for compilation.
One key was changed in "button-target.h" for compatibility with Rockboy.
This also caused the changes to "keymap-zenxfi3.c", to keep the stock functionality (no further changes in here).
Change-Id: Ic222faf89e9a9a2332a49d6e532cedb6eb16d3d7
Reviewed-on: http://gerrit.rockbox.org/762
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Apart from the fact that the original settings were much
to sensitive for my taste, they are now easier configurable.
Change-Id: If1772367fc1f34fa1255f57b1831d1f33dc34558
Reviewed-on: http://gerrit.rockbox.org/772
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
Before, the Cypress chip power is always turn on either from internal battery
or from usb host. In this regard, the internal battery energy was spend on the
inactive chip. Now power of the Cypress chip is enabled only on the external usb host.
Change-Id: Iae7cddd1237ea9ed93fee5404575cc01543cb00c
Reviewed-on: http://gerrit.rockbox.org/433
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
When the align parameter was a 32bit value (like all default integer literals),
and the to-be-aligned value is a pointer the upper 32bit got corrupted because
the value was casted down to 32bit.
Note: This hasnt been a problem because apparently the sim always gets 32bit
addresses (I found this when compiling Rockbox as a library).
Change-Id: I0d2d3fd8bfa210326b27162bb22c059da97d207a
Turn on 4x oversampling inside UDA1380 codec.
This allow will move the quantization noise to the higher frequencies,
that slightly improve the final sound quality.
Change-Id: Idf79cd877c526d8937a47c34e9c180d837a15db1
Reviewed-on: http://gerrit.rockbox.org/435
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
Reviewed-by: Björn Stenberg <bjorn@haxx.se>
Defining HAVE_BUTTON_DATA without simultaneously defining HAVE_TOUCHSCREEN
caused compile errors. (I need them separated for a scrollstrip driver.)
Change-Id: I945d3437d840035ccc0c147f8155029b403c6ec2
Reviewed-on: http://gerrit.rockbox.org/771
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
add_event_ex is added that takes an extra user_data pointer. This pointer is
passed to the callback (add_event and add_event_ex have slightly different
callbacks types). All callbacks also get the event id passed. Events added
with add_event_ex must be removed with remove_event_ex because the user_data
pointer must match in addition to the callback pointer.
On the other add_event is simplified to omit the oneshort parameter which
was almost always false (still there with add_event_ex).
As a side effect the ata_idle_notify callbacks are changed as well, they
do not take a data parameter anymore which was always NULL anyway.
This commit also adds some documentation to events.h
Change-Id: I13e29a0f88ef908f175b376d83550f9e0231f772
This complements offset-based resume and playback start funcionality.
The implementation is global on both HWCODEC and SWCODEC.
Basically, if either the specified elapsed or offset are non-zero,
it indicates a mid-track resume.
To resume by time only, set elapsed to nonzero and offset to zero.
To resume by offset only, set offset to nonzero and elapsed to zero.
Which one the codec uses and which has priority is up to the codec;
however, using an elapsed time covers more cases:
* Codecs not able to use an offset such as VGM or other atomic
formats
* Starting playback at a nonzero elapsed time from a source that
contains no offset, such as a cuesheet
The change re-versions pretty much everything from tagcache to nvram.
Change-Id: Ic7aebb24e99a03ae99585c5e236eba960d163f38
Reviewed-on: http://gerrit.rockbox.org/516
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
The build system needed fixes because the tools paths changed and one tool that
we used (apkbuilder) was removed entirely. Recent NDKs don't ship gcc 4.4.3
anymore, therefore switch to 4.6. The code itself needed a fix for a jni
reference bug that was uncovered by KitKat.
The port now builds with latest sdk (r22) and ndk (r9d).
Change-Id: Id74fa54ba93bbb0ee30373fbe79e92c5ff03201d
With the lcd underflow code at work, it results in small flicker when
switching frequency but it should be fine because it doesn't happen very
often and I don't think there is a way to avoid it without disabling EMI
frequency scaling.
Change-Id: I458732d52bbf27cda2510c3836539db1fb24ea15
For some reason the power subsystem needs to know the relationship between
the VDD{D,A,IO} and uses a weird register to do so.
Change-Id: I7fcc75f6cc0460b4997914986deda7ca544a4940
Contrary to the imx233, the stmp37xx lcdif doesn't know how to properly
recover from underflow and things are worse because of the errata which
makes the lcdif not clear the fifo. Workaround this by detecting underflow
and taking action: stop dotclk mode (will clear fifo) and schedule next frame.
The dma transfers now write the ctrl register as part of the PIO writes,
making the code simpler.
Change-Id: I15abc24567f322cd03bf2ef7903094f7f0178427
Uses a cosine factor to smoothly shift the PCM level from the old level
to the new one over the length of a frame.
Implements indirect calls to PCM scaling function instead of testing
conditions on every callback, cleanly assigning a different call to
do the volume transition. The volume change call then assigns the final
scaling function.
Change-Id: If1004b92a91c5ca766dd0e4014ec274636e8ed26
Reviewed-on: http://gerrit.rockbox.org/763
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
Implement scanning as binary tree in array.
Make the ADC calls fewer without compromising read quality.
Declare the thread function as 'noreturn' to save some stack. Reduce
stack size (regardless, % use is now a bit lower).
Change-Id: I239792fd2a0a2c019d1ec4af1d6d4b466cdf0ef5
I must have been blind and copied some intermediate file
instead of final version. No functional change, only fixes.
Change-Id: Icaa868225517662c88f8492b1f04808407853361
No code changed, just shuffling stuff around. This should make it easier to
build only select parts kernel and use different implementations.
Change-Id: Ie1f00f93008833ce38419d760afd70062c5e22b5
This patch adds a configurable line separator between list items, very
similar to lists in Android. Additionally, below the list item there is a
thicker line. It can be disabled in the settings. Its color can
be configured as well.
Remote and monochrome displays are explicitly unsupported. If there is desire
this can be changed but it doesn't seem useful to me.
Change-Id: I005313b0d8f5ecd15864bf20e66ea4e3390d8b7d
DPI values are autogenerated from the resolution and collected display size
values. These values are inserted as comments as well.
Change-Id: Id03aedf9af18348f773dfce002805e480f6751e8
1) Avoid load/store delay slot by reorganizing instructions
in copy loops
2) Fix off-by-one error in cache initialization code.
This was harmless as it simply set line0 twice, now it sets
every cacheline only once.
3) Fix off-by-word error in .bss clearing loop.
The addiu in branch delay slot even if calculated is not seen
by the branch instruction itself, so the code did one word
too much in clearing.
4) Fix off-by-word error in deadbeefing stack.
See above.
Change-Id: Iabb09a55979de7aa2e2b9234273683fc7e9762c5
A missing comma messed the lookup table up :'( Be aware that the kernel
on the ypr0 doesn't support many codepages in which case its default (iso8859)
will be used.
Change-Id: Iaa4a4b8338fb047d29f6a4e2a80eba5c296d27ce
"/" couldn't be opened. This regression was introduced by 731072d. Trailing
slash should not be stripped for the root directory.
Change-Id: Idd2d9b1f33e7be789bcf432e586e6715eb4152f4
This is needed for readdir() and dir_get_info() to work properly because
they depend on hash/path matching.
Change-Id: Ibd23def10eebabd76cdddac2739a5274159e88a9
It's quite rare that it is called for a symlink to a directory. But it only
needs a second syscall to stat() if that happened. Therefore speed up the
common case by avoiding an unecessary second syscall.
Change-Id: I911105f76631ebccc7696a1540e9cf069a706000
The two functions need to check whether they are called for a specific path
to implement the virtual mount point for the external storage. This
is statistically rare and a hit on the common case. Therefore speed up
the common case by performing integer comparision first, and only expensive
string construction and comparision if that succeeds.
Change-Id: I3c41fe073e1f4f8eb62d2b8556a36937c9cb8290
A thread polls the appropriate GPIO pin for sd card presence and mounts
using the mount system call.
Change-Id: I31ab41c4120f4af64eb6998b7e7b6f9051585efb
The external storage will be created during make install, as simext folder in
the build directory. Upon pressing the e key the sim will mount (virtually
) this into the root directory. It can be accessed in the same way as an
sd/mmc card on real targets. This requires quite some path trickery in io.c.
Change-Id: I2fa9070a3146101ec5655b5b4115ca349d1d4bf4
Part of this change is to align sdlapp builds to other application targets
in that the sim_* wrappers are not used anymore (except for sim_read/write).
Path mangling is now done in rbpaths.c as well.
Change-Id: I9726da73b50a83d9e1a1840288de16ec01ea029d
The iocharset mount option names the codepages slightly differently and
must be translated properly.
Change-Id: I147a256e3453136282244201c27225a30cdfdca0
The virtual external storage can be inserted/extracted with the e key. This
has little effect because there is no way to access the storage (yet, a later
commit will change this). Except on ondio where the mmc needs to be
extracted before entering USB (like on real target).
Change-Id: I523402832f3b4ae71e0603b281aba4fb8592a897
CONFIG_STORAGE & STORAGE_HOSTFS allows to use parts of the storage_* API to be
compiled for application targets without compiling storage.c or performing
actually raw storage access. This is primarily to enable application targets to
implement HAVE_MULTIVOMULE/HAVE_HOTSWAP (in a later commit).
SIMULATOR uses the same mechanism without explicitely defining STORAGE_HOSTFS
(how to add a bit to an existing preprocessor token?).
Change-Id: Ib3f8ee0d5231e2ed21ff00842d51e32bc4fc7292
This driver will subsume the old button-lradc driver and support far more
options. It can sense LRADC channels, PSWITCH, GPIOs and it handles special
"buttons" like headphone insertion and hold detection. It also provides a
more natural description of the buttons using a target-defined table with some
macros to make it easy to read and write. It uniformely handles debouncing on
LRADC channels and PSWITCH.
Change-Id: Ie61d1f593fdcf3bd456ba1d53a1fd784286834ce
On some OSes like Windows or if running in a virtual machine, the one second
timeout might be too short.
Change-Id: I717f7a2aaed1cb3d40e8fbe6f9b1081b43ceea95
Original fix by Marcin: it had a problem because crt0 on imx233 is more
complicated than many targets: since we use virtual memory, we first disable
the MMU, then move the entire image (including init and itext stuff), then
setup a temporary stack to setup the MMU. Only when the MMU is enabled, can
we move the init and itext stuff to its right location and finally boot.
This requires some trickery because:
- the initial move copies everything, including init and itext
- the stack overlaps with init and itext to reclaim space
- the temporary stack cannot be the same as the main stack to avoid trashing
the init and itext code, also it needs to be a physical address
Change-Id: Ibaf331c7d90b61f99225d93c9e621eb0f3f8f2dc
Rework the irq code, to put more code in the C part. When interrupt
nesting is enable, Rockbox gets pretty unstable so disable it for now.
Change-Id: Iee18b539c80ea408273f6082975faaa87d3ee1b6
