Maybe it's not possible to change NAK while the DMA engine is active.
Burst probably can't hurt.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@27052 a1c6a512-1295-4272-9138-f99709370657
it achieves all the requirements, work fine on c200v2, and is much simpler
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26933 a1c6a512-1295-4272-9138-f99709370657
Reserve 1MB of DRAM for loading rockbox and use the rest as BSS
Write sdram setup in assembler and move it to a separate file, together
with MMU init code
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26926 a1c6a512-1295-4272-9138-f99709370657
not working yet : an empty drive is detected
won't link on fuzev1: drivers allocated in usb_storage.c are too large
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26905 a1c6a512-1295-4272-9138-f99709370657
has made it more reliable. It seems to basically work now, but
somehow when Linux tries to read the partition table and it gets the
"scsi read10" command, the storage_read_sectors(drive=0, start=0, count=8)
call never returns...
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26894 a1c6a512-1295-4272-9138-f99709370657
we still need to convert uncached addresses to physical addresses
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26177 a1c6a512-1295-4272-9138-f99709370657
No need for special address handling, all addresses are equal to their physical address
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26176 a1c6a512-1295-4272-9138-f99709370657
build it on fuzev2 and clipv2 too, it should be the same controller
as3525v1 file is only build for CONFIG_USBOTG == USBOTG_AS3525, no need
to check for it in the .c file
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26142 a1c6a512-1295-4272-9138-f99709370657
Note to self: Next time don't forget to check a AMSv2 build before committing...
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26130 a1c6a512-1295-4272-9138-f99709370657
-> Change references to as3517 into as3515
there is a reference to the as3515 in the public as3525 datasheet to
support this fact
as3517 is used in the as3527 SoC, the (public) as3527 datasheet has
detailed information on its registers
the audio codec/PMU used in as3525v2 (thought to be as3543) appears to be
compatible (identical?) with as3517
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26075 a1c6a512-1295-4272-9138-f99709370657
as3525 comes with a as3517, as3525v2 with a as3543, rename specific
registers accordingly
Existing problems: FM (line out) doesn't work, volume can't go below a
certain point
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25260 a1c6a512-1295-4272-9138-f99709370657
When read it returns all enabled interrupt sources
When written it enables interrupt sources for each bit set
So just like VIC_INT_EN_CLEAR, we don't have to read the previous value
before writing to it (VIC_INT_EN_CLEAR is write-only anyway)
Thanks to Fred Bauer for spotting
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23734 a1c6a512-1295-4272-9138-f99709370657
Implement usb_enable()
Reorder/Modify usb_drv_init() to match closer the OF and remove a freeze
(USB registers were accessed before the USB module was enabled)
Add a panic in USB isr to be sure we notice when it's called
Reset GPIOA direction for usb_detect() to notice extraction
Add some comments
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23184 a1c6a512-1295-4272-9138-f99709370657
Work based on AMD 5536 linux driver and AMD Geode CS5536 datasheet
Rockbox still doesn't reboot on USB insert
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@21689 a1c6a512-1295-4272-9138-f99709370657
