Motivation:
This driver began as a set of functions to help to test and
experiment with different DMA configurations. It is cumbersome,
time consuming, and leads to mistakes to handle LLIs and DMA
registers dispersed along the code.
Later, i decided to adapt an old DMA queue driver written in the
past for a similar (scatter-gather) controller, all task/queue
code is based on the old driver.
Finally, some cleaning and dmac_ch_get_info() function was added
to complete RB needs.
Description:
- Generic, can be used by other targets including the same
controller. Not difficult to adapt for other similar
controllers if necesary.
- Easy to experiment and compare results using different
setups and/or queue algorithms:
Multi-controller and fully configurable from an unique place.
All task and LLI management is done by the driver, user only
has to (statically) allocate them.
- Two queue modes:
QUEUE_NORMAL: each task in the queue is launched using a new
DMA transfer once previous task is finished.
QUEUE_LINK: when a task is queued, it is linked with the last
queued task, creating a single continuous DMA transfer. New
tasks must be queued while the channel is running, otherwise
the continuous DMA transfer will be broken.
On Classic, QUEUE_LINK mode is needed for I2S continuous
transfers, QUEUE_NORMAL is used for LCD and could be useful
in the future for I2C or UART (non-blocking serial debug) if
necessary.
- Robust DMA transfer progress info (peak meter), needs final
testing, see below.
Technical details about DMA progress:
There are comments in the code related to the method actually
used (sequence method), it reads progress without halting the
DMA transfer. Althought the datasheet does not recommend to do
that, the sequence method seems to be robust, I ran tests calling
dmac_ch_get_info() millions of times and the results were always
as expected (tests done at 2:1 CPU/AHB clock ratio, no other
ratios were tried but probably sequence method will work for any
typical ratio).
This controller allows to halt the transfer and drain the DMAC
FIFO, DMA requests are ignored when the DMA channel is halted.
This method is not suitable for playback because FIFO is never
drained to I2S peripheral (who raises the DMA requests). This
method probably works for capture, the FIFO is drained to memory
before halting.
Another way is to disable (stop) the playback channel. When the
channel is disabled, all FIFO data is lost. It is unknown how much
the FIFO was filled when it was cleared, SRCADDR counter includes
the lost data, therefore the only useful information is LINK and
COUNT, that is the same information disponible when using the
sequence method. At this point we must procced in the same way as
in sequence method, in addition the playback channel should be
relaunched (configure + start) after calculating real SRCADDR.
The stop+relaunch method should work, it is a bit complicated,
and not valid for all peripheral FIFO configurations (depending
on stream rate). Moreover, due to the way the COUNT register is
implemented in HW, I suspect that this method will fail when
source and destination bus widths doesn't match. And more
important, it is not easy to garantize that no sample is lost
here or there, using the sequence method we can always be sure
that playback is ok.
Change-Id: Ib12a1e2992e2b6da4fc68431128c793a21b4b540
This patch implements a simple API to use the external interrupt
hardware present on s5l8702 (GPIO interrupt controller). This
GPIOIC has been fully tested using emcore apps.
Code is based on openiBoot project, there are a few modifications
to optimize space considering we will only use two or three external
interrupts. The API compiles and works, but has been never used,
therefore probably will need some changes to the final version.
External interrupts are necessary for jack remote+mic controller
(see iAP Interface Specifiction: Headphone Remote and Mic System),
this controller is located at I2C bus address 0x72, there is a IRQ
line for remote button press/release events routed to GPIO E6. At
this moment, the functionallity of this controller has been
extensively tested using emcore, getting a lot of information about
how it works. Microphone is already working on RB, jack accessory
detection and button events are work in progress.
PMU IRQ line is also routed to GPIO F3, it signals many events:
holdswitch, usb plug, wall adapter, low battery... The use of PMU
interrupts is the orthodox way of doing things, at this moment
there is no work done in this direction, there are a lot of PMU
events and i think it is a matter of discursion what to do and how.
Change-Id: Icc2e48965e664ca56c9518d84a81c9d9fdd31736
Depends on http://gerrit.rockbox.org/r/#/c/1043/.
This patch adds a new setting in Settings -> General
-> System: Freq Scaling Governor
Usable in Quickscreen and Shortcuts.
Possible settings are:
- Conservative: Slow frequency switching.
- Ondemand or Interactive: Fast frequency switching.
- Powersave: Allways lowest frequency.
- Performance: Allways highest frequency.
German translation provided.
This may be genric for Android kernel based devices but is only enabled
for iBasso Devices. Other maintainers may choose do adopt this.
Change-Id: I10296f5be9586ad3a409105db0cd03682a30e9c1
Reorganization
- Separated iBasso devices from PLATFORM_ANDROID. These are now standlone
hosted targets. Most device specific code is in the
firmware/target/hosted/ibasso directory.
- No dependency on Android SDK, only the Android NDK is needed.
32 bit Android NDK and Android API Level 16.
- Separate implementation for each device where feasible.
Code cleanup
- Rewrite of existing code, from simple reformat to complete reimplementation.
- New backlight interface, seperating backlight from touchscreen.
- Rewrite of device button handler, removing unneeded code and fixing memory
leaks.
- New Debug messages interface logging to Android adb logcat (DEBUGF, panicf,
logf).
- Rewrite of lcd device handler, removing unneeded code and fixing memory leaks.
- Rewrite of audiohw device handler/pcm interface, removing unneeded code and
fixing memory leaks, enabling 44.1/48kHz pthreaded playback.
- Rewrite of power and powermng, proper shutdown, using batterylog results
(see http://gerrit.rockbox.org/r/#/c/1047/).
- Rewrite of configure (Android NDK) and device specific config.
- Rewrite of the Android NDK specific Makefile.
Misc
- All plugins/games/demos activated.
- Update tinyalsa to latest from https://github.com/tinyalsa/tinyalsa.
Includes
- http://gerrit.rockbox.org/r/#/c/993/
- http://gerrit.rockbox.org/r/#/c/1010/
- http://gerrit.rockbox.org/r/#/c/1035/
Does not include http://gerrit.rockbox.org/r/#/c/1007/ due to new backlight
interface and new option for hold switch, touchscreen, physical button
interaction.
Rockbox needs the iBasso DX50/DX90 loader for startup, see
http://gerrit.rockbox.org/r/#/c/1099/
The loader expects Rockbox to be installed in /mnt/sdcard/.rockbox/. If
/mnt/sdcard/ is accessed as USB mass storage device, Rockbox will exit
gracefully and the loader will restart Rockbox on USB disconnect.
Tested on iBasso DX50.
Compiled (not tested) for iBasso DX90.
Compiled (not tested) for PLATFORM_ANDROID.
Change-Id: I5f5e22e68f5b4cf29c28e2b40b2c265f2beb7ab7
The port to for this two targets has been entirely developped by Ilia Sergachev (alias Il or xzcc). His source
can be found at https://bitbucket.org/isergachev/rockbox . The few necesary modifications for the DX90 port
was done by headwhacker form head-fi.org. Unfortunately i could not try out the final state of the DX90 port.
The port is hosted on android (without java) as standalone app. The official Firmware is required to run this port.
Ilia did modify the source files for the "android" target in the rockbox source to make the DX port work. The work I did
was to separate the code for DX50 (&DX90) from the android target.
On this Target Ilia used source from tinyalsa from AOSP. I did not touch that part of the code because I do not understand it.
What else I changed from Ilias sources besides the separation from the target "android":
* removed a dirty hack to keep backlight off
* changed value battery meter to voltage battery meter
* made all plugins compile (named target as "standalone") and added keymaps
* i added the graphics for the manual but did not do anything else for the manual yet
* minor optimizations
known bugs:
* timers are slowed donw when playback is active (tinyalsa related?)
* some minor bugs
Things to do:
* The main prolem will be how to install the app correctly. A guy called DOC2008 added a CWM (by androtab.info) to the
official firmware and Ilia made a CWM installation script and a dualboot selector (rbutils/ibassoboot, build with
ndk-build). We will have to find a way to install rockbox in a proper way without breaking any copyrights.
Maybe ADB is an option but it is not enable with OF by default. Patching the OF is probably the way to go.
* All the wiki and manual
to build:
needed: android ndk installed, android sdk installed with additional build-tools 19.1.0 installed
./tools/configure
select iBasso DX50 or iBasso DX90
make -j apk
the content of rockbox.zip/.rockbox needs to be copied to /system/rockbox/app_rockbox/rockbox/ (rockbox app not needed)
the content of libs/armeabi to /system/rockbox/lib/ (rockbox app needed)
The boot selector is needed as /system/bin/MangoPlayer and the iBasso app as /system/bin/MangoPlayer_original. There
is also the "vold" file. The one from OF does not work with DX50 rockbox (DX90 works!?), the one from Ilia is necessary.
Until we have found a proper way to install it, it can only be installed following the instructions of Ilia on his
bitbucket page, using the CWM-OF and his installation script package.
Change-Id: Ic4faaf84824c162aabcc08e492cee6e0068719d0
Reviewed-on: http://gerrit.rockbox.org/941
Tested: Chiwen Chang <rock1104.tw@yahoo.com.tw>
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
This patch redoes the filesystem code from the FAT driver up to the
clipboard code in onplay.c.
Not every aspect of this is finished therefore it is still "WIP". I
don't wish to do too much at once (haha!). What is left to do is get
dircache back in the sim and find an implementation for the dircache
indicies in the tagcache and playlist code or do something else that
has the same benefit. Leaving these out for now does not make anything
unusable. All the basics are done.
Phone app code should probably get vetted (and app path handling
just plain rewritten as environment expansions); the SDL app and
Android run well.
Main things addressed:
1) Thread safety: There is none right now in the trunk code. Most of
what currently works is luck when multiple threads are involved or
multiple descriptors to the same file are open.
2) POSIX compliance: Many of the functions behave nothing like their
counterparts on a host system. This leads to inconsistent code or very
different behavior from native to hosted. One huge offender was
rename(). Going point by point would fill a book.
3) Actual running RAM usage: Many targets will use less RAM and less
stack space (some more RAM because I upped the number of cache buffers
for large memory). There's very little memory lying fallow in rarely-used
areas (see 'Key core changes' below). Also, all targets may open the same
number of directory streams whereas before those with less than 8MB RAM
were limited to 8, not 12 implying those targets will save slightly
less.
4) Performance: The test_disk plugin shows markedly improved performance,
particularly in the area of (uncached) directory scanning, due partly to
more optimal directory reading and to a better sector cache algorithm.
Uncached times tend to be better while there is a bit of a slowdown in
dircache due to it being a bit heavier of an implementation. It's not
noticeable by a human as far as I can say.
Key core changes:
1) Files and directories share core code and data structures.
2) The filesystem code knows which descriptors refer to same file.
This ensures that changes from one stream are appropriately reflected
in every open descriptor for that file (fileobj_mgr.c).
3) File and directory cache buffers are borrowed from the main sector
cache. This means that when they are not in use by a file, they are not
wasted, but used for the cache. Most of the time, only a few of them
are needed. It also means that adding more file and directory handles
is less expensive. All one must do in ensure a large enough cache to
borrow from.
4) Relative path components are supported and the namespace is unified.
It does not support full relative paths to an implied current directory;
what is does support is use of "." and "..". Adding the former would
not be very difficult. The namespace is unified in the sense that
volumes may be specified several times along with relative parts, e.g.:
"/<0>/foo/../../<1>/bar" :<=> "/<1>/bar".
5) Stack usage is down due to sharing of data, static allocation and
less duplication of strings on the stack. This requires more
serialization than I would like but since the number of threads is
limited to a low number, the tradoff in favor of the stack seems
reasonable.
6) Separates and heirarchicalizes (sic) the SIM and APP filesystem
code. SIM path and volume handling is just like the target. Some
aspects of the APP file code get more straightforward (e.g. no path
hashing is needed).
Dircache:
Deserves its own section. Dircache is new but pays homage to the old.
The old one was not compatible and so it, since it got redone, does
all the stuff it always should have done such as:
1) It may be update and used at any time during the build process.
No longer has one to wait for it to finish building to do basic file
management (create, remove, rename, etc.).
2) It does not need to be either fully scanned or completely disabled;
it can be incomplete (i.e. overfilled, missing paths), still be
of benefit and be correct.
3) Handles mounting and dismounting of individual volumes which means
a full rebuild is not needed just because you pop a new SD card in the
slot. Now, because it reuses its freed entry data, may rebuild only
that volume.
4) Much more fundamental to the file code. When it is built, it is
the keeper of the master file list whether enabled or not ("disabled"
is just a state of the cache). Its must always to ready to be started
and bind all streams opened prior to being enabled.
5) Maintains any short filenames in OEM format which means that it does
not need to be rebuilt when changing the default codepage.
Miscellaneous Compatibility:
1) Update any other code that would otherwise not work such as the
hotswap mounting code in various card drivers.
2) File management: Clipboard needed updating because of the behavioral
changes. Still needs a little more work on some finer points.
3) Remove now-obsolete functionality such as the mutex's "no preempt"
flag (which was only for the prior FAT driver).
4) struct dirinfo uses time_t rather than raw FAT directory entry
time fields. I plan to follow up on genericizing everything there
(i.e. no FAT attributes).
5) unicode.c needed some redoing so that the file code does not try
try to load codepages during a scan, which is actually a problem with
the current code. The default codepage, if any is required, is now
kept in RAM separarately (bufalloced) from codepages specified to
iso_decode() (which must not be bufalloced because the conversion
may be done by playback threads).
Brings with it some additional reusable core code:
1) Revised file functions: Reusable code that does things such as
safe path concatenation and parsing without buffer limitations or
data duplication. Variants that copy or alter the input path may be
based off these.
To do:
1) Put dircache functionality back in the sim. Treating it internally
as a different kind of file system seems the best approach at this
time.
2) Restore use of dircache indexes in the playlist and database or
something effectively the same. Since the cache doesn't have to be
complete in order to be used, not getting a hit on the cache doesn't
unambiguously say if the path exists or not.
Change-Id: Ia30f3082a136253e3a0eae0784e3091d138915c8
Reviewed-on: http://gerrit.rockbox.org/566
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
Forms implemented to a greater or lesser degree at the moment:
ll_* = singly-linked list
lld_* = doubly-linked list
lldc_* = doubly-linked circular list
Change-Id: Ieed5af50fc59165c8b14c3513b3b5d0e6f7de9fa
* Seal away private thread and kernel definitions and declarations
into the internal headers in order to better hide internal structure.
* Add a thread-common.c file that keeps shared functions together.
List functions aren't messed with since that's about to be changed to
different ones.
* It is necessary to modify some ARM/PP stuff since GCC was complaining
about constant pool distance and I would rather not force dump it. Just
bl the cache calls in the startup and exit code and let it use veneers
if it must.
* Clean up redundant #includes in relevant areas and reorganize them.
* Expunge useless and dangerous stuff like remove_thread().
Change-Id: I6e22932fad61a9fac30fd1363c071074ee7ab382
Any number of readers may be in the critical section at a time and writers
are mutually exclusive to all other threads. They are a better choice when
data is rarely modified but often read and multiple threads can safely
access it for reading.
Priority inheritance is fully implemented along with other changes to the
kernel to fully support it on multiowner objects.
This also cleans up priority code in the kernel and updates some associated
structures in existing objects to the cleaner form.
Currently doesn't add the mrsw_lock.[ch] files since they're not yet
needed by anything but the supporting improvements are still useful.
This includes a typed bitarray API (bitarray.h) which is pretty basic
for now.
Change-Id: Idbe43dcd9170358e06d48d00f1c69728ff45b0e3
Reviewed-on: http://gerrit.rockbox.org/801
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
With LCD driver all calculation will be performed on RGB888 and the hardware/OS
can display from our 24bit framebuffer.
It is not yet as performance optimized as the existing drivers but should be
good enough.The vast number of small changes is due to the fact that
fb_data can be a struct type now, while most of the code expected a scalar type.
lcd-as-memframe ASM code does not work with 24bit currently so the with 24bit
it enforces the generic C code.
All plugins are ported over. Except for rockpaint. It uses so much memory that
it wouldnt fit into the 512k plugin buffer anymore (patches welcome).
Change-Id: Ibb1964545028ce0d8ff9833ccc3ab66be3ee0754
There is no simple method to detect radio through the 3-wire interface, so it's
not implemented for the YH-925 for now. YH-920 always has a radio.
Change-Id: Iea484d752915fcd40dbbbd7dbbf13e81aaf548db
No code changed, just shuffling stuff around. This should make it easier to
build only select parts kernel and use different implementations.
Change-Id: Ie1f00f93008833ce38419d760afd70062c5e22b5
This driver will subsume the old button-lradc driver and support far more
options. It can sense LRADC channels, PSWITCH, GPIOs and it handles special
"buttons" like headphone insertion and hold detection. It also provides a
more natural description of the buttons using a target-defined table with some
macros to make it easy to read and write. It uniformely handles debouncing on
LRADC channels and PSWITCH.
Change-Id: Ie61d1f593fdcf3bd456ba1d53a1fd784286834ce
This patch includes some refactoring:
- renaming according to Rockbox guidelines
- GPIO code merging, still with target defines
- some simplification in firmware/SOURCES
Change-Id: I7fd95aece53f40efdf8caac22348376615795431
This is the basic port to the new target Samsung
YP-R1, which runs on a similar platform as YP-R0.
Port is usable, although there are still
some optimizations that have to be done.
Change-Id: If83a8e386369e413581753780c159026d9e41f04
The port uses the imx233 soc, it's a STMP3650 based Samsung player
Change-Id: I50b6d7e77fd292fab5ed26de87853cd5aaf9eaa4
Reviewed-on: http://gerrit.rockbox.org/490
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
Choices are limited for those: i2c is either generic software or imx233
hardware and power is either none or with a gpio. So factor ever possible
combination in a single common file and use fmradio-target.h to supply the
required parameters. This will remove a bunch of duplicate code.
Change-Id: If12faeb2e371631cd39cc18a4c1d859812007934
The old code allowed each target to specify its adc targets but this proved
useless since the target rely directly on imx233/lradc for input method and
generic adc is mostly used for battery and debug. Remove all target specific
files and provide a generic implemenation. The targets can still specify a
battery temperature channel in powermgmt-target.h
Change-Id: I68cf2e3e46379d174ac6d774ffb237bb15a19ae3
HiFi E.T. MA8 is almost the same as MA9 except
another DAC(pcm1792 in ma8, df1704 in ma9).
MA8 has ILI9342 lcd, MA8C has ILI9342C lcd.
Change-Id: If2ac04f5a3382590b2a392c46286559f54b2ed6a
The only difference between this target and HiFi E.T. MA9
is display driver (ILI9342 in MA9 and ILI9342c in MA9C)
Change-Id: Icc3d2490f850902a653175360f12283f3708bbb7
Enable simulator for the target ypr0 to
be built and used.
Change-Id: I1b080f07ab90f5c4856881d08ad70e1053bbb0c0
Reviewed-on: http://gerrit.rockbox.org/618
Reviewed-by: Frank Gevaerts <frank@gevaerts.be>
Target that have a touchpad/touchscreen should disable it while
being locked (In order to avoid LCD to drain battery power due to
"key locked" constant reporting messages. If they a have a keylock
button this was already handled at driver level. If not (e.g. fuze+),
they will have to implement a switch at driver level that action.c
can operate on softlock.
This patch does the following for any target having a touchpad
or a touchscreen and no HAS_BUTTON_HOLD (ie any softlock target)
1) it implements the code to call button_enable_touch(bool en) in
action.c.
2) button_enable_touch is implemented in button.c and call
either touchpad_enable or touchscreen_enable
3) those two function are implemented respectively in touchscreen.c
and a new touchpad.c file. They provide a generic way to silents touch's
device and call a function at driver level where target specific code
can be implemented if possible/needed (for power saving for instance).
Those function name are touchpad_enable_device and touchscreen_enable_device
4) we implement an empty function at driver level of targets that need it
to have them still being able to compiled.
Change-Id: I9ead78a25bd33466a8533f5b9f259b395cb5ce49
Reviewed-on: http://gerrit.rockbox.org/569
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
The idea is to share loading code between bootloaders and rolo().
Change-Id: I1656ed91946d7a05cb7c9fa7a16793c3c862a5cd
Reviewed-on: http://gerrit.rockbox.org/190
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
The driver is current unused and very minimal. It can used on
targets which have an accessible UART port and it will be used on
some creative targets as backlight control.
Change-Id: Id710d63574aadb0a2d7327b03187506b469470b1
Based on FS#9920 by Ryan Press with changes to selection logic so
that it works on my iPod Photo. Should also work on iPod Color/4G
and Mini2G. Moved all target specific code from
firmware/drivers/serial.c into new file
firmware/target/arm/pp/uart-pp.c in the same manner as other
target specific uart code.
Update to fix build error on ipodmini2g by adding defines in config file.
Removed unwanted whitespace
Tested on iPod Photo.
Change-Id: Ia5539563966198e06372d70b5adf2ef78882f863
Reviewed-on: http://gerrit.rockbox.org/455
Reviewed-by: andypotter <liveboxandy@gmail.com>
Tested-by: andypotter <liveboxandy@gmail.com>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
This is going right in since it's long overdue. If anything is goofed,
drop me a line or just tweak it yourself if you know what's wrong. :-)
Make HW/SW codec interface more uniform when emulating HW functionality
on SWCODEC for functions such as "audiohw_set_pitch". The firmware-to-
DSP plumbing is in firmware/drivers/audiohw-swcodec.c. "sound_XXX"
APIs are all in sound.c with none in DSP code any longer.
Reduce number of settings definitions needed by each codec by providing
defaults for common ones like balance, channels and SW tone controls.
Remove need for separate SIM code and tables and add virtual codec header
for hosted targets.
Change-Id: I3f23702bca054fc9bda40f49824ce681bb7f777b
Implements double-buffered volume, balance and prescaling control in
the main PCM driver when HAVE_SW_VOLUME_CONTROL is defined ensuring
that all PCM is volume controlled and level changes are low in latency.
Supports -73 to +6 dB using a 15-bit factor so that no large-integer
math is needed.
Low-level hardware drivers do not have to implement it themselves but
parameters can be changed (currently defined in pcm-internal.h) to work
best with a particular SoC or to provide different volume ranges.
Volume and prescale calls should be made in the codec driver. It should
appear as a normal hardware interface. PCM volume calls expect .1 dB
units.
Change-Id: Idf6316a64ef4fb8abcede10707e1e6c6d01d57db
Reviewed-on: http://gerrit.rockbox.org/423
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
As per title this patch aims at splitting common target
code and specific target code in a better way to
support future ports within the same environment
(e.g. Samsung YP-R1 where the Linux and the SoC
are the same, with differences in hardware devices
handling)
Change-Id: I67b4918c46403b184d3d8f42ab5aae7d01037fd0
Reviewed-on: http://gerrit.rockbox.org/409
Reviewed-by: Thomas Martitz <kugel@rockbox.org>
Tested-by: Thomas Martitz <kugel@rockbox.org>
CPU frequency scaling is basically useless without scaling the
memory frequency. On the i.MX233, the EMI (external memory
interface) and DRAM blocks are responsable for the DDR settings.
This commits implements emi frequency scaling. Only some settings
are implemented and the timings values only apply to mDDR
(extracted from Sigmatel linux port) and have been checked to
work on the Fuze+ and Zen X-Fi2/3. This feature is still disabled
by default but I expected some battery life savings by boosting
higher to 454MHz and unboosting lower to 64MHz.
Note that changing the emi frequency is particularly tricky and
to avoid writing it entirely in assembly we rely on the compiler
to not use the stack except in the prolog and epilog (because
it's in dram which is disabled when doing the change) and to put
constant pools in iram which should always be true if the
compiler isn't completely dumb and since the code itself is put
in iram. If this proves to be insufficient, one can always switch
the stack to the irq stack since interrupts are disabled during
the change.
Change-Id: If6ef5357f7ff091130ca1063e48536c6028f23ba
Merge sd and mmc drivers into a single sdmmc driver. This allows
some factoring of the code and simplify bug fixing. Also fix the
dma/cache related issue by doing all transfers via a correctly
aligned buffer. The current code is not smart enough to take
advantage of large user buffers currently but at least it is safe!
Change-Id: Ib0fd16dc7d52ef7bfe99fd586e03ecf08691edcd
Logs information, errors, etc to disk using the register_storage_idle_func
mechanism to write to the disk when available. Currently, this is disabled
in normal builds, but can be enabled by adding ROCKBOX_HAS_LOGDISKF to the
config file. By default, it uses a 2KB buffer and drops text if the buffer
overflows.
The system includes a simple warning level mechanism that can be used to by
default exclude non-serious errors from logging on release builds.
Change-Id: I0a3d186a93625c7c93dae37b993a0d37e5a3a925
Reviewed-on: http://gerrit.rockbox.org/288
Reviewed-by: Jonathan Gordon <rockbox@jdgordon.info>
Tested-by: Michael Giacomelli <mgiacomelli@gmail.com>
Reviewed-by: Michael Giacomelli <mgiacomelli@gmail.com>
Basically it uses the default SI4700 radio chip driver, the only thing that's different is the I2C access,
written specifically to interact with my kernel module.
Next things to add are:
- RDS support!
Change-Id: I0ed125641e00f93124d7a34f90dd508e7f1db5a4
Signed-off-by: Lorenzo Miori <memorys60@gmail.com>
Refactor native/hosted implementation seperation while at it
(no wrappers starting with _ anymore).
Change-Id: If68ae89700443bb3be483c1cace3d6739409560a
The freescale firmware partitions has a lots of quirks that
need to be dealt with, so do it the proper way.
Change-Id: I8a5bd3fb462a4df143bc6c931057f3ffedd4b3d3
The icoll code now has an IRQ storm detection mechanism which
will prevent the device from hard freezing in case it happen.
Change-Id: I9861238dce61d29af1e48f9c534ec63a7f23465c
Simplified stack unwinder for ARM. This is port of
http://www.mcternan.me.uk/ArmStackUnwinding/
backtrace() is called from UIE() on native targets
and from panicf() on both native and ARM RaaA.
Change-Id: I8e4b3c02490dd60b30aa372fe842d193b8929ce0
Now lcd_framebuffer is the only framebuffer in the system. We still use a ARM-buffered buffer
which serve as an intermediate buffer for copying, to accomodate the requirement of the controller.
We implement lcd_update_rect() properly using this new scheme (this requires two little quirks),
this allows to implement lcd_blit_yuv with the right semantic (bypasses the framebuffer). YUV to RGB
conversion is still done in software but the DCP CSC should be able to do that but the hardware rotation
scheme is not the same as our software so it will require some tricks.
Change-Id: I0752e9c2f1a705d2e6a6010084e1f150965d8370
Core, codecs and plugins link it separately so this gets rid of SOURCES trickery.
Don't build it for hosted targets.
Change-Id: If15ef90e93cd218a4352ae8e89eea95d3122452f
move prototypes to ascodec.h
move code to ascodec*.c
YPR0: use adc-as3514.c instead of duplicating it
TODO: merge as3514.h and ascodec.h ?
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31626 a1c6a512-1295-4272-9138-f99709370657
* Introduce CONFIG_BATTERY_MEASURE define, to allow targets (application)
to break powermgmt.c's assumption about the ability to read battery voltage.
There's now additionally percentage (android) and remaining time measure
(maemo). No measure at all also works (sdl app). If voltage can't be measured,
then battery_level() is king and it'll be used for power_history and runtime
estimation.
* Implement target's API in the simulator, i.e. _battery_voltage(), so it
doesn't need to implement it's own powermgmt.c and other stubs. Now
the sim behaves much more like a native target, although it still
changes the simulated battery voltage quickly,
* Other changes include include renaming battery_adc_voltage() to
_battery_voltage(), for consistency with the new target functions and
making some of the apps code aware that voltage and runtime estimation
is not always available.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31548 a1c6a512-1295-4272-9138-f99709370657
Voltage can be read using as3543 adc (i.e. ascodec api, on this target implemented
via ioctl()). TODO: Look into possibly controlling charging more by re-using
powermgmt-ascodec.c. However, charging seems to be controlled by the kernel,
so may not be needed.
Charger state can be read using /dev/minivet. It allows to differentiate between
wall charger and usb charging, but that's not implemented (is it even worthwhile?)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31470 a1c6a512-1295-4272-9138-f99709370657
This port is a hybrid native/RaaA port. It runs on a embedded linux system,
but is the only application. It therefore can implement lots of stuff that
native targets also implement, while leveraging the underlying linux kernel.
The port is quite advanced. User interface, audio playback, plugins work
mostly fine. Missing is e.g. power mangement and USB (see SamsungYPR0 wiki page).
Included in utils/ypr0tools are scripts and programs required to generate
a patched firmware. The patched firmware has the rootfs modified to load
Rockbox. It includes a early/safe USB mode.
This port needs a new toolchain, one that includes glibc headers and libraries.
rockboxdev.sh can generate it, but e.g. codesourcey and distro packages may
also work.
Most of the initial effort is done by Lorenzo Miori and others (on ABI),
including reverse engineering and patching of the original firmware,
initial drivers, and more. Big thanks to you.
Flyspray: FS#12348
Author: Lorenzo Miori, myself
Merry christmas to ypr0 owners! :)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31415 a1c6a512-1295-4272-9138-f99709370657
The new menu is very helpful on RaaA, but also shown in the sim. It shows
the process cpu usage, process' time stats (user,sys,real) and the cpu
frequency stats.
It uses a thread to sample the data, however the thread is not created
until the menu is visited for the first time.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31364 a1c6a512-1295-4272-9138-f99709370657
Massage the way it interfaces a bit to make things more flexible.
The chroma_buf scheme on Sansa Connect and Creative ZVx calling the
lcd_write_yuv420_lines implementation in lcd-as-memframe.S with five params
with a chroma buffer that the function can't use wouldn't work anyway so just
have them use the stock implementation (really, how was that working?).
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31335 a1c6a512-1295-4272-9138-f99709370657
For this commit: Sansa e200v1, Gigabeat F, Gigabeat S and Mini2440 are
changed over. Quite a number of other targets probably can be as well.
General LCD code is moved out of the target drivers into
drivers/lcd-memframe.c.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31311 a1c6a512-1295-4272-9138-f99709370657
Only done for files shared across multiple targets
Note that several targets share the same CONFIG_LCD but use completely
different drivers
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31285 a1c6a512-1295-4272-9138-f99709370657
add a comment about why we don't return 0 when no tuner was detected
build the file on all as3525v2 targets
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31284 a1c6a512-1295-4272-9138-f99709370657
pcf5060*.c has the same name than the RTC driver, but it's not the RTC driver itself
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31280 a1c6a512-1295-4272-9138-f99709370657
tuner and rtcs are already included by CONFIG_TUNER and CONFIG_RTC
It's not possible to remove all duplicates, because some models must support 2 RTCs.
a bitfield could be used instead, like is done for CONFIG_TUNER
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31279 a1c6a512-1295-4272-9138-f99709370657
Merge clipv1/clipv2 code since they use the same 3x3 matrix
clipzip keyscan buttons now work in bootloader
clipplus untouched (no matrix)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31235 a1c6a512-1295-4272-9138-f99709370657
Included are drivers for buttons, backlight, lcd, audio and storage.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@31000 a1c6a512-1295-4272-9138-f99709370657
Origional implementation by Robert Keevil with contributions from Frederik Vestre, Stoyan Stratev, Craig Elliott, Michael Sparmann, Thomas Schott, Rosso Maltese, and syncs from a bunch of other people!
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30995 a1c6a512-1295-4272-9138-f99709370657
The buflib memory allocator is handle based and can free and
compact, move or resize memory on demand. This allows to effeciently
allocate memory dynamically without an MMU, by avoiding fragmentation
through memory compaction.
This patch adds the buflib library to the core, along with
convinience wrappers to omit the context parameter. Compaction is
not yet enabled, but will be in a later patch. Therefore, this acts as a
replacement for buffer_alloc/buffer_get_buffer() with the benifit of a debug
menu.
See buflib.h for some API documentation.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@30380 a1c6a512-1295-4272-9138-f99709370657
