rockbox/firmware/target/arm/as3525/sansa-clipzip/lcd-clipzip.c

/***************************************************************************
 *             __________               __   ___.
 *   Open      \______   \ ____   ____ |  | _\_ |__   _______  ___
 *   Source     |       _//  _ \_/ ___\|  |/ /| __ \ /  _ \  \/  /
 *   Jukebox    |    |   (  <_> )  \___|    < | \_\ (  <_> > <  <
 *   Firmware   |____|_  /\____/ \___  >__|_ \|___  /\____/__/\_ \
 *                     \/            \/     \/    \/            \/
 * $Id$
 *
 * Copyright (C) 2008 François Dinel
 * Copyright (C) 2008-2009 Rafaël Carré
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version 2
 * of the License, or (at your option) any later version.
 *
 * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
 * KIND, either express or implied.
 *
 ****************************************************************************/
#include "config.h"

#include "lcd.h"
#include "lcd-clip.h"
#include "system.h"
#include "cpu.h"

/* the detected lcd type (0 or 1) */
static int lcd_type;

/* initialises the host lcd hardware, returns the lcd type */
int lcd_hw_init(void)
{
    /* configure SSP */
    bitset32(&CGU_PERI, CGU_SSP_CLOCK_ENABLE);
    SSP_CPSR = 8;           /* TODO: use AS3525_SSP_PRESCALER, OF uses 8 */
    SSP_CR0 =   (0 << 8) |  /* SCR, serial clock rate divider = 1 */
                (1 << 7) |  /* SPH, phase = 1 */
                (1 << 6) |  /* SPO, polarity = 1 */
                (0 << 4) |  /* FRF, frame format = motorola SPI */
                (7 << 0);   /* DSS, data size select = 8 bits */
    SSP_CR1 =   (1 << 3) |  /* SOD, slave output disable = 1 */
                (0 << 2) |  /* MS, master/slave = master */
                (1 << 1) |  /* SSE, synchronous serial port enabled = true */
                (0 << 0);   /* LBM, loopback mode = normal */
    SSP_IMSC &= ~0xF;       /* disable interrupts */
    SSP_DMACR &= ~0x3;      /* disable DMA */

    /* configure GPIO B2 (lcd D/C#) as output */
    GPIOB_DIR |= (1<<2);

    /* configure GPIO B3 (lcd type detect) as input */
    GPIOB_DIR &= ~(1<<3);

    /* configure GPIO A5 (lcd reset# ?) as output and set low */
    GPIOA_DIR |= (1 << 5);
    GPIOA_PIN(5) = 0;

    /* detect lcd type on GPIO B3 */    
    return GPIOB_PIN(3) ? 1 : 0;
}

/* writes a command byte to the LCD */
static void lcd_write_cmd(uint8_t byte)
{
    /* wait until not busy */
    while (SSP_SR & (1<<4));

    /* LCD command mode */
    GPIOB_PIN(2) = 0;
    
    /* write data */
    SSP_DATA = byte;
    
    /* wait until not busy */
    while (SSP_SR & (1<<4));

    /* LCD data mode */
    GPIOB_PIN(2) = (1 << 2);
}

/* writes a data byte to the LCD */
static void lcd_write_dat(uint8_t data)
{
    /* wait while transmit FIFO */
    while (!(SSP_SR & (1<<1)));   

    /* write data */
    SSP_DATA = data;
}

/* writes both a command and data value to the lcd */
static void lcd_write(uint8_t cmd, uint8_t data)
{
    lcd_write_cmd(cmd);
    lcd_write_dat(data);
}

/* delays during lcd initialisation (for type 0 LCDs) */
static void lcd_delay(int us)
{
    udelay(us);
}

/* initialises lcd type 0 */
static void lcd_init_type0(void)
{
    lcd_write(0x01, 0x00);
    lcd_write(0x14, 0x01);
    lcd_delay(5);

    lcd_write(0x14, 0x00);
    lcd_delay(5);

    lcd_write(0x0F, 0x41);
    lcd_write(0xEA, 0x0A);
    lcd_write(0xEB, 0x42);
    lcd_write(0x18, 0x08);
    lcd_write(0x1A, 0x0B);
    lcd_write(0x48, 0x03);

    /* lcd width/height */
    lcd_write(0x30, 0x00);
    lcd_write(0x31, 0x5F);
    lcd_write(0x32, 0x00);
    lcd_write(0x33, 0x5F);

    lcd_write(0xE0, 0x10);
    lcd_write(0xE1, 0x00);
    lcd_write(0xE5, 0x00);
    lcd_write(0x0D, 0x00);
    lcd_write(0x1D, 0x01);
    lcd_write(0x09, 0x00);
    lcd_write(0x13, 0x00);
    lcd_write(0x16, 0x05);
    lcd_write(0x3A, 0x03);
    lcd_write(0x3B, 0x03);
    lcd_write(0x3C, 0x03);
    lcd_write(0x3D, 0x45);
    lcd_write(0x3E, 0x45);
    lcd_write(0x3F, 0x45);
    lcd_write(0x40, 0x62);
    lcd_write(0x41, 0x3D);
    lcd_write(0x42, 0x46);
}

/* writes a table entry (for type 1 LCDs) */
static void lcd_write_table(uint8_t val)
{
    lcd_write_dat((val >> 4) & 0x07);
    lcd_write_dat((val >> 0) & 0x0F);
}

/* initialises lcd type 1 */
static void lcd_init_type1(void)
{
    static const uint8_t curve[256] = {
        /* 5-bit curve */
        0, 5, 10, 15, 20, 25, 30, 35, 39, 43, 47, 51, 55, 59, 63, 67,
        71, 75, 79, 83, 87, 91, 95, 99, 103, 105, 109, 113, 117, 121, 123, 127,
        /* 6-bit curve */
        0, 2, 4, 6, 8, 10, 12, 16, 18, 24, 26, 28, 30, 32, 34, 36,
        38, 40, 42, 44, 46, 48, 50, 52, 54, 56, 58, 60, 62, 64, 66, 68,
        70, 72, 76, 78, 80, 82, 84, 86, 88, 90, 92, 94, 96, 98, 100, 102,
        104, 106, 108, 110, 112, 114, 116, 118, 120, 121, 122, 123, 124, 125, 126, 127,
        /* 5-bit curve */
        0, 5, 10, 15, 20, 25, 30, 35, 39, 43, 47, 51, 55, 59, 63, 67,
        71, 75, 79, 83, 87, 91, 93, 97, 101, 105, 109, 113, 117, 121, 124, 127
    };
    int i;

    lcd_write_cmd(0x02);
    lcd_write_dat(0x00);

    lcd_write_cmd(0x01);

    lcd_write_cmd(0x03);
    lcd_write_dat(0x00);

    lcd_write_cmd(0x04);
    lcd_write_dat(0x03);

    lcd_write_cmd(0x05);
    lcd_write_dat(0x08);

    lcd_write_cmd(0x06);
    lcd_write_dat(0x00);

    lcd_write_cmd(0x07);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);
    lcd_write_dat(0x04);
    lcd_write_dat(0x1F);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);
    lcd_write_dat(0x05);
    lcd_write_dat(0x0F);

    lcd_write_cmd(0x08);
    lcd_write_dat(0x01);

    lcd_write_cmd(0x09);
    lcd_write_dat(0x07);

    /* lcd width/height */
    lcd_write_cmd(0x0A);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);
    lcd_write_dat(0x05);
    lcd_write_dat(0x0F);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);
    lcd_write_dat(0x05);
    lcd_write_dat(0x0F);

    lcd_write_cmd(0x0B);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);

    lcd_write_cmd(0x0E);
    lcd_write_dat(0x04);
    lcd_write_dat(0x02);
    lcd_write_dat(0x02);
    lcd_write_dat(0x05);
    lcd_write_dat(0x03);
    lcd_write_dat(0x0F);

    lcd_write_cmd(0x0F);
    lcd_write_dat(0x0A);
    lcd_write_dat(0x0A);
    lcd_write_dat(0x0A);

    lcd_write_cmd(0x1C);
    lcd_write_dat(0x08);

    lcd_write_cmd(0x1D);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);
    lcd_write_dat(0x00);

    lcd_write_cmd(0x1E);
    lcd_write_dat(0x05);

    lcd_write_cmd(0x1F);
    lcd_write_dat(0x00);

    lcd_write_cmd(0x30);
    lcd_write_dat(0x10);

    lcd_write_cmd(0x3A);
    for (i = 0; i < 256; i++) {
        lcd_write_table(curve[i]);
    }

    lcd_write_cmd(0x3C);
    lcd_write_dat(0x00);

    lcd_write_cmd(0x3D);
    lcd_write_dat(0x00);
}

/* initialises the lcd */
void lcd_init_device(void)
{
    lcd_type = lcd_hw_init();
    if (lcd_type == 0) {
        lcd_init_type0();
    }
    else {
        lcd_init_type1();
    }
}

/* sets up the lcd to receive frame buffer data */
static void lcd_setup_rect(int x, int x_end, int y, int y_end)
{
    if (lcd_type == 0) {
        lcd_write(0x34, x);
        lcd_write(0x35, x_end);
        lcd_write(0x36, y);
        lcd_write(0x37, y_end);
    }
    else {
        lcd_write_cmd(0x0A);
        lcd_write_dat((x >> 8) & 0xFF);
        lcd_write_dat((x >> 0) & 0xFF);
        lcd_write_dat((x_end >> 8) & 0xFF);
        lcd_write_dat((x_end >> 0) & 0xFF);
        lcd_write_dat((y >> 8) & 0xFF);
        lcd_write_dat((y >> 0) & 0xFF);
        lcd_write_dat((y_end >> 8) & 0xFF);
        lcd_write_dat((y_end >> 0) & 0xFF);
    }
}

/* Updates a fraction of the display. */
void lcd_update_rect(int x, int y, int width, int height)
{
    fb_data *ptr;
    fb_data pixel;
    int row, col;
    int x_end = x + width;
    int y_end = y + height;

    /* check rectangle */
    if ((x >= LCD_WIDTH) || (x_end <= 0) || (y >= LCD_HEIGHT) || (y_end <= 0)) {
        /* rectangle is outside visible display, do nothing */
        return;
    }
    
    /* correct rectangle (if necessary) */
    if (x < 0) {
        x = 0;
    }
    if (x_end > LCD_WIDTH) {
        x_end = LCD_WIDTH;
    }
    if (y < 0) {
        y = 0;
    }
    if (y_end > LCD_HEIGHT) {
        y_end = LCD_HEIGHT;
    }

    /* setup GRAM write window */
    lcd_setup_rect(x, x_end - 1, y, y_end - 1);

    /* write to GRAM */
    lcd_write_cmd((lcd_type == 0) ? 0x08 : 0x0C);
    for (row = y; row < y_end; row++) {
        ptr = &lcd_framebuffer[row][x];
        for (col = x; col < x_end; col++) {
            pixel = *ptr++;
            lcd_write_dat((pixel >> 8) & 0xFF);
            lcd_write_dat((pixel >> 0) & 0xFF);
        }
    }
}

/* updates the entire lcd */
void lcd_update(void)
{
    lcd_update_rect(0, 0, LCD_WIDTH, LCD_HEIGHT);
}