rockbox/firmware/target/coldfire/iaudio/lcd-remote-iaudio.c

/***************************************************************************
 *             __________               __   ___.
 *   Open      \______   \ ____   ____ |  | _\_ |__   _______  ___
 *   Source     |       _//  _ \_/ ___\|  |/ /| __ \ /  _ \  \/  /
 *   Jukebox    |    |   (  <_> )  \___|    < | \_\ (  <_> > <  <
 *   Firmware   |____|_  /\____/ \___  >__|_ \|___  /\____/__/\_ \
 *                     \/            \/     \/    \/            \/
 * $Id$
 *
 * Copyright (C) 2006 by Linus Nielsen Feltzing
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version 2
 * of the License, or (at your option) any later version.
 *
 * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
 * KIND, either express or implied.
 *
 ****************************************************************************/

#include "config.h"
#include "system.h"
#include "kernel.h"
#include "lcd-remote.h"
#include "scroll_engine.h"

/* The LCD in the iAudio M3/M5/X5 remote control is a Tomato LSI 0350 */

#define LCD_SET_DUTY_RATIO 0x48
#define LCD_SELECT_ADC     0xa0
#define LCD_SELECT_SHL     0xc0
#define LCD_SET_COM0       0x44
#define LCD_OSC_ON         0xab
#define LCD_SELECT_DCDC    0x64
#define LCD_SELECT_RES     0x20
#define LCD_SET_VOLUME     0x81
#define LCD_SET_BIAS       0x50
#define LCD_CONTROL_POWER  0x28
#define LCD_DISPLAY_ON     0xae
#define LCD_SET_INITLINE   0x40
#define LCD_SET_COLUMN     0x10
#define LCD_SET_PAGE       0xb0
#define LCD_SET_GRAY       0x88
#define LCD_SET_PWM_FRC    0x90
#define LCD_SET_POWER_SAVE 0xa8
#define LCD_REVERSE        0xa6

#define CS_LO      and_l(~0x00000020, &GPIO1_OUT)
#define CS_HI      or_l(0x00000020, &GPIO1_OUT)
#define CLK_LO     and_l(~0x00004000, &GPIO_OUT)
#define CLK_HI     or_l(0x00004000, &GPIO_OUT)
#define DATA_LO    and_l(~0x00002000, &GPIO_OUT)
#define DATA_HI    or_l(0x00002000, &GPIO_OUT)
#define RS_LO      and_l(~0x00008000, &GPIO_OUT)
#define RS_HI      or_l(0x00008000, &GPIO_OUT)

/* cached settings values */
static bool cached_invert = false;
static bool cached_flip = false;
static int cached_contrast = DEFAULT_REMOTE_CONTRAST_SETTING;

bool remote_initialized = false;


int lcd_remote_default_contrast(void)
{
    return DEFAULT_REMOTE_CONTRAST_SETTING;
}

#if 0 // FIXME
void lcd_remote_powersave(bool on)
{
    if(remote_initialized) {
        if (on)
            lcd_remote_write_command(LCD_SET_POWER_SAVE | 1);
        else
            lcd_remote_write_command(LCD_SET_POWER_SAVE | 1);
    }
}
#endif

void lcd_remote_set_contrast(int val)
{
    if (val < 0)
        val = 0;
    else if (val > 63)
        val = 63;

    cached_contrast = val;
    if(remote_initialized)
        lcd_remote_write_command_ex(LCD_SET_VOLUME, val);
}

bool remote_detect(void)
{
    return (GPIO_READ & 0x01000000)?false:true;
}

void lcd_remote_on(void)
{
    CS_HI;
    CLK_HI;
    sleep(HZ/100);
    
    lcd_remote_write_command(LCD_SET_DUTY_RATIO);
    lcd_remote_write_command(0x70);  /* 1/128 */
    
    lcd_remote_write_command(LCD_OSC_ON);
    
    lcd_remote_write_command(LCD_SELECT_DCDC | 2); /* DC/DC 5xboost */
    
    lcd_remote_write_command(LCD_SELECT_RES | 7); /* Regulator resistor: 7.2 */
    
    lcd_remote_write_command(LCD_SET_BIAS | 6); /* 1/11 */
    
    lcd_remote_write_command(LCD_CONTROL_POWER | 7); /* All circuits ON */

    sleep(3*HZ/100);
    
    lcd_remote_write_command_ex(LCD_SET_GRAY | 0, 0x00);
    lcd_remote_write_command_ex(LCD_SET_GRAY | 1, 0x00);
    lcd_remote_write_command_ex(LCD_SET_GRAY | 2, 0x0c);
    lcd_remote_write_command_ex(LCD_SET_GRAY | 3, 0x00);
    lcd_remote_write_command_ex(LCD_SET_GRAY | 4, 0xcc);
    lcd_remote_write_command_ex(LCD_SET_GRAY | 5, 0x00);
    lcd_remote_write_command_ex(LCD_SET_GRAY | 6, 0xcc);
    lcd_remote_write_command_ex(LCD_SET_GRAY | 7, 0x0c);
    
    lcd_remote_write_command(LCD_SET_PWM_FRC | 6); /* 3FRC + 12PWM */
    
    lcd_remote_write_command(LCD_DISPLAY_ON | 1); /* display on */

    remote_initialized = true;

    lcd_remote_set_flip(cached_flip);
    lcd_remote_set_contrast(cached_contrast);
    lcd_remote_set_invert_display(cached_invert);
}

void lcd_remote_off(void)
{
    remote_initialized = false;
    CS_HI;
    RS_HI;
}

void lcd_remote_poweroff(void)
{
    /* Set power save -> Power OFF (VDD - VSS) .. that's it */
    if (remote_initialized)
        lcd_remote_write_command(LCD_SET_POWER_SAVE | 1);
}

#ifndef BOOTLOADER
/* Monitor remote hotswap */
static void remote_tick(void)
{
    static bool last_status = false;
    static int countdown = 0;
    bool current_status;

    current_status = remote_detect();

    /* Only report when the status has changed */
    if (current_status != last_status)
    {
        last_status = current_status;
        countdown = current_status ? 20*HZ : 1;
    }
    else
    {
        /* Count down until it gets negative */
        if (countdown >= 0)
            countdown--;

        if (current_status)
        {
            if (!(countdown % 48))
            {
                queue_broadcast(SYS_REMOTE_PLUGGED, 0);
            }
        }
        else
        {
            if (countdown == 0)
            {
                queue_broadcast(SYS_REMOTE_UNPLUGGED, 0);
            }
        }
    }
}
#endif

void lcd_remote_init_device(void)
{
    or_l(0x0000e000, &GPIO_OUT);
    or_l(0x0000e000, &GPIO_ENABLE);
    or_l(0x0000e000, &GPIO_FUNCTION);
    
    or_l(0x00000020, &GPIO1_OUT);
    or_l(0x00000020, &GPIO1_ENABLE);
    or_l(0x00000020, &GPIO1_FUNCTION);
    
    and_l(~0x01000000, &GPIO_OUT);
    and_l(~0x01000000, &GPIO_ENABLE);
    or_l(0x01000000, &GPIO_FUNCTION);

    lcd_remote_clear_display();
    if (remote_detect())
        lcd_remote_on();
#ifndef BOOTLOADER
    tick_add_task(remote_tick);
#endif
}

/* Update the display.
   This must be called after all other LCD functions that change the display. */
void lcd_remote_update(void)
{
    int y;
    if(remote_initialized) 
    {
        for(y = 0;y < LCD_REMOTE_FBHEIGHT;y++) 
        {
            /* Copy display bitmap to hardware.
               The COM48-COM63 lines are not connected so we have to skip
               them. Further, the column address doesn't wrap, so we
               have to update one page at a time. */
            lcd_remote_write_command(LCD_SET_PAGE | (y > 5 ? y + 2 : y));
            lcd_remote_write_command_ex(LCD_SET_COLUMN | 0, 0);
            lcd_remote_write_data(FBREMOTEADDR(0, y), LCD_REMOTE_WIDTH);
        }
    }
}

/* Update a fraction of the display. */
void lcd_remote_update_rect(int x, int y, int width, int height)
{
    if(remote_initialized) 
    {
        int ymax;

        /* The Y coordinates have to work on even 8 pixel rows */
        ymax = (y + height-1) >> 3;
        y >>= 3;

        if(x + width > LCD_REMOTE_WIDTH)
            width = LCD_REMOTE_WIDTH - x;
        if (width <= 0)
            return; /* nothing left to do, 0 is harmful to lcd_write_data() */
        if(ymax >= LCD_REMOTE_FBHEIGHT)
            ymax = LCD_REMOTE_FBHEIGHT-1;

        /* Copy specified rectangle bitmap to hardware
           COM48-COM63 are not connected, so we need to skip those */
        for (; y <= ymax; y++) 
        {
            lcd_remote_write_command(LCD_SET_PAGE 
                                     | ((y > 5 ? y + 2 : y) & 0xf));
            lcd_remote_write_command_ex(LCD_SET_COLUMN | ((x >> 4) & 0xf),
                                        x & 0xf);

            lcd_remote_write_data(FBREMOTEADDR(x,y), width);
        }
    }
}

void lcd_remote_set_invert_display(bool yesno)
{
    cached_invert = yesno;
    if(remote_initialized)
        lcd_remote_write_command(LCD_REVERSE | yesno);
}

void lcd_remote_set_flip(bool yesno)
{
    cached_flip = yesno;
    if(remote_initialized) 
    {
        if(yesno) 
        {
            lcd_remote_write_command(LCD_SELECT_ADC | 0);
            lcd_remote_write_command(LCD_SELECT_SHL | 0);
            lcd_remote_write_command_ex(LCD_SET_COM0, 16);
        } 
        else 
        {
            lcd_remote_write_command(LCD_SELECT_ADC | 1);
            lcd_remote_write_command(LCD_SELECT_SHL | 8);
            lcd_remote_write_command_ex(LCD_SET_COM0, 0);
        }
    }
}