115 lines
5 KiB
C
115 lines
5 KiB
C
|
/***************************************************************************
|
||
|
|
* __________ __ ___.
|
||
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
||
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
||
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
||
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
||
|
|
* \/ \/ \/ \/ \/
|
||
|
|
* $Id$
|
||
|
|
*
|
||
|
|
* Copyright (C) 2008 by Michael Sevakis
|
||
|
|
*
|
||
|
|
* This program is free software; you can redistribute it and/or
|
||
|
|
* modify it under the terms of the GNU General Public License
|
||
|
|
* as published by the Free Software Foundation; either version 2
|
||
|
|
* of the License, or (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
||
|
|
* KIND, either express or implied.
|
||
|
|
*
|
||
|
|
****************************************************************************/
|
||
|
|
#ifndef POWERMGMT_TARGET_H
|
||
|
|
#define POWERMGMT_TARGET_H
|
||
|
|
|
||
|
|
/* Can't just run this code willy-nilly. Do not allow charger engagement
|
||
|
|
* without carefully verifying compatibility.
|
||
|
|
*
|
||
|
|
* Things to check:
|
||
|
|
* 1) Charge path configuration for the PMIC.
|
||
|
|
* 2) Correct thermistor reading
|
||
|
|
* 3) Accurate voltage readings
|
||
|
|
* 4) Accurate current sense for the charge path as the sense resistor may
|
||
|
|
* deviate from the 0.1 ohms assumed by the charge path regulator.
|
||
|
|
*/
|
||
|
|
#ifdef TOSHIBA_GIGABEAT_S
|
||
|
|
/*
|
||
|
|
* Gigabeat S qualifications:
|
||
|
|
* 1) Setup for dual-supply mode with separate inputs and providing USB
|
||
|
|
* charging capability through external components.
|
||
|
|
* 2) Curve obtained experimentally - extreme deviation from "optimized"
|
||
|
|
* characteristics.
|
||
|
|
* 3) Verified at battery terminals - no deviation from datasheet formula.
|
||
|
|
* 4) 0.316 ohms <=?? - verified by comparitive current readings on device
|
||
|
|
* with ammeter readings and measurement of on-board components.
|
||
|
|
*/
|
||
|
|
#ifndef BOOTLOADER
|
||
|
|
#define IMX31_ALLOW_CHARGING
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#else
|
||
|
|
#warning This iMX31 target requires validation of charging algorithm - charging disabled
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#define BATT_VTRICKLE_CHARGE 2900 /* Must charge slowly */
|
||
|
|
#define BATT_VSLOW_CHARGE 3500 /* Lower-current charge mode below
|
||
|
|
* this level */
|
||
|
|
#define BATT_VAUTO_RECHARGE 4100 /* When to begin another cycle */
|
||
|
|
#define BATT_USB_VAUTO_RECHARGE 4000 /* When to cycle with USB only */
|
||
|
|
#define BATT_USB_VSTOP 4140 /* When to "stop" when USB only */
|
||
|
|
#define BATT_TOO_LOW 2400 /* No battery? Short? Can't
|
||
|
|
read below 2400mV. */
|
||
|
|
#define CHARGER_TOTAL_TIMER 300 /* minutes */
|
||
|
|
|
||
|
|
/* .316 ohms is closest standard value as measured in 1% tolerance - adjust
|
||
|
|
* relative to .100 ohm which is what the PMIC is "tuned" for. */
|
||
|
|
#define ILEVEL_ADJUST_IN(I) (100*(I) / 316)
|
||
|
|
#define ILEVEL_ADJUST_OUT(I) (316*(I) / 100)
|
||
|
|
|
||
|
|
/* Relative draw to battery capacity - adjusted for sense resistor */
|
||
|
|
#define BATTERY_ICHARGE_COMPLETE (505*9/100) /* 9% of nominal max output */
|
||
|
|
/* All charging modes use 4.200V for regulator */
|
||
|
|
#define BATTERY_VCHARGING MC13783_VCHRG_4_200V
|
||
|
|
/* Slow charging - MAIN - Still below 3.5V (avoid excessive reg. dissipation) */
|
||
|
|
/* #define BATTERY_ISLOW */
|
||
|
|
/* Fast charging - MAIN */
|
||
|
|
#define BATTERY_IFAST MC13783_ICHRG_1596MA /* 505mA */
|
||
|
|
/* Trickle charging low battery - MAIN (~10% Imax) */
|
||
|
|
#define BATTERY_ITRICKLE MC13783_ICHRG_177MA /* 56mA */
|
||
|
|
/* Slow charging - USB - Still below 3.5V (avoid excessive reg. dissipation) */
|
||
|
|
/* #define BATTERY_ISLOW_USB */
|
||
|
|
/* Fast charging - USB */
|
||
|
|
#define BATTERY_IFAST_USB MC13783_ICHRG_1152MA /* 365mA */
|
||
|
|
/* Trickle charging low battery - USB (Ibat = Icccv - Idevice) */
|
||
|
|
#define BATTERY_ITRICKLE_USB MC13783_ICHRG_532MA /* 168mA */
|
||
|
|
/* Maintain charge - USB 500mA */
|
||
|
|
#define BATTERY_IFLOAT_USB MC13783_ICHRG_1152MA /* 365mA */
|
||
|
|
#define BATTERY_VFLOAT_USB MC13783_VCHRG_4_150V
|
||
|
|
/* Maintain charge - USB 100mA */
|
||
|
|
#define BATTERY_IMAINTAIN_USB MC13783_ICHRG_266MA /* 84mA */
|
||
|
|
#define BATTERY_VMAINTAIN_USB MC13783_VCHRG_4_150V
|
||
|
|
|
||
|
|
/* Battery filter lengths in samples */
|
||
|
|
#define BATT_AVE_SAMPLES 32
|
||
|
|
#define ICHARGER_AVE_SAMPLES 32
|
||
|
|
|
||
|
|
/* Provide filtered charge current */
|
||
|
|
int battery_charge_current(void);
|
||
|
|
|
||
|
|
#ifndef SIMULATOR
|
||
|
|
/* Indicate various functions that require implementation at the target level.
|
||
|
|
* This is because the battery could be low or the battery switch is off but
|
||
|
|
* with the main charger attached which implies safe power for anything. The
|
||
|
|
* true battery reading is always reported for voltage readings and not the
|
||
|
|
* value at the application supply. */
|
||
|
|
#define TARGET_QUERY_FORCE_SHUTDOWN
|
||
|
|
|
||
|
|
/* For this the application supply is read out if the charger is attached or
|
||
|
|
* the battery read if not (completely hardware selected at BP). */
|
||
|
|
#define TARGET_BATTERY_LEVEL_SAFE
|
||
|
|
|
||
|
|
/* The state should be adjusted to CHARGING or DISCHARGING */
|
||
|
|
#define TARGET_POWERMGMT_FILTER_CHARGE_STATE
|
||
|
|
#endif /* SIMULATOR */
|
||
|
|
|
||
|
|
#endif /* POWERMGMT_TARGET_H */
|