f2f34881ec
Remove audiohw_mute from header as well, and make this function static to each driver (commented out when it was unused) git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25733 a1c6a512-1295-4272-9138-f99709370657
280 lines
6.9 KiB
C
280 lines
6.9 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (c) 2009 Mark Arigo
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#include "config.h"
|
|
#include "system.h"
|
|
#include "string.h"
|
|
|
|
/*#define LOGF_ENABLE*/
|
|
#include "logf.h"
|
|
|
|
#include "pcm_sampr.h"
|
|
#include "audio.h"
|
|
#include "akcodec.h"
|
|
#include "audiohw.h"
|
|
#include "sound.h"
|
|
|
|
const struct sound_settings_info audiohw_settings[] = {
|
|
[SOUND_VOLUME] = {"dB", 0, 1,-127, 0, -25},
|
|
/* HAVE_SW_TONE_CONTROLS */
|
|
[SOUND_BASS] = {"dB", 0, 1, -24, 24, 0},
|
|
[SOUND_TREBLE] = {"dB", 0, 1, -24, 24, 0},
|
|
[SOUND_BALANCE] = {"%", 0, 1,-100, 100, 0},
|
|
[SOUND_CHANNELS] = {"", 0, 1, 0, 5, 0},
|
|
[SOUND_STEREO_WIDTH] = {"%", 0, 5, 0, 250, 100},
|
|
#if defined(HAVE_RECORDING)
|
|
[SOUND_LEFT_GAIN] = {"dB", 1, 1, 0, 31, 23},
|
|
[SOUND_RIGHT_GAIN] = {"dB", 1, 1, 0, 31, 23},
|
|
[SOUND_MIC_GAIN] = {"dB", 1, 1, 0, 1, 0},
|
|
#endif
|
|
};
|
|
|
|
static unsigned char akc_regs[AKC_NUM_REGS];
|
|
|
|
static void akc_write(int reg, unsigned val)
|
|
{
|
|
if ((unsigned)reg >= AKC_NUM_REGS)
|
|
return;
|
|
|
|
akc_regs[reg] = (unsigned char)val;
|
|
akcodec_write(reg, val);
|
|
}
|
|
|
|
static void akc_set(int reg, unsigned bits)
|
|
{
|
|
akc_write(reg, akc_regs[reg] | bits);
|
|
}
|
|
|
|
static void akc_clear(int reg, unsigned bits)
|
|
{
|
|
akc_write(reg, akc_regs[reg] & ~bits);
|
|
}
|
|
|
|
static void akc_write_masked(int reg, unsigned bits, unsigned mask)
|
|
{
|
|
akc_write(reg, (akc_regs[reg] & ~mask) | (bits & mask));
|
|
}
|
|
|
|
#if 0
|
|
static void codec_set_active(int active)
|
|
{
|
|
(void)active;
|
|
}
|
|
#endif
|
|
|
|
/* convert tenth of dB volume (-1270..0) to master volume register value */
|
|
int tenthdb2master(int db)
|
|
{
|
|
if (db < VOLUME_MIN)
|
|
return 0xff; /* mute */
|
|
else if (db >= VOLUME_MAX)
|
|
return 0x00;
|
|
else
|
|
return ((-db)/5);
|
|
}
|
|
|
|
int sound_val2phys(int setting, int value)
|
|
{
|
|
int result;
|
|
|
|
switch(setting)
|
|
{
|
|
#ifdef HAVE_RECORDING
|
|
case SOUND_LEFT_GAIN:
|
|
case SOUND_RIGHT_GAIN:
|
|
result = (value - 23) * 15; /* fix */
|
|
break;
|
|
case SOUND_MIC_GAIN:
|
|
result = value * 200; /* fix */
|
|
break;
|
|
#endif
|
|
default:
|
|
result = value;
|
|
break;
|
|
}
|
|
|
|
return result;
|
|
}
|
|
|
|
/*static void audiohw_mute(bool mute)
|
|
{
|
|
if (mute)
|
|
{
|
|
akc_set(AK4537_DAC, SMUTE);
|
|
udelay(200000);
|
|
}
|
|
else
|
|
{
|
|
udelay(200000);
|
|
akc_clear(AK4537_DAC, SMUTE);
|
|
}
|
|
}*/
|
|
|
|
void audiohw_preinit(void)
|
|
{
|
|
int i;
|
|
for (i = 0; i < AKC_NUM_REGS; i++)
|
|
akc_regs[i] = akcodec_read(i);
|
|
|
|
/* POWER UP SEQUENCE (from the datasheet) */
|
|
/* Note: the delay length is what the OF uses, although the datasheet
|
|
suggests they can be shorter */
|
|
|
|
/* power up VCOM */
|
|
akc_set(AK4537_PM1, PMVCM);
|
|
udelay(100000);
|
|
|
|
/* setup AK4537_SIGSEL1 */
|
|
akc_set(AK4537_SIGSEL1, ALCS | MOUT2);
|
|
udelay(100000);
|
|
|
|
/* setup AK4537_SIGSEL2 */
|
|
akc_write_masked(AK4537_SIGSEL2, DAHS, (DAHS | HPL | HPR));
|
|
udelay(100000);
|
|
|
|
/* setup AK4537_MODE1 */
|
|
akc_write_masked(AK4537_MODE1, DIF_I2S | BICK_32FS | MCKI_PLL_12000KHZ,
|
|
(DIF_MASK | BICK_MASK | MCKI_MASK));
|
|
udelay(100000);
|
|
|
|
/* CLOCK SETUP - X'tal used in PLL mode (master mode) */
|
|
|
|
/* release the pull-down of the XTI pin and power-up the X'tal osc */
|
|
akc_write_masked(AK4537_PM2, PMXTL, (MCLKPD | PMXTL));
|
|
udelay(100000);
|
|
|
|
/* power-up the PLL */
|
|
akc_set(AK4537_PM2, PMPLL);
|
|
udelay(100000);
|
|
|
|
/* enable MCKO output and setup MCKO output freq */
|
|
akc_set(AK4537_MODE1, MCKO_EN);
|
|
udelay(100000);
|
|
|
|
/* ENABLE HEADPHONE AMP OUTPUT */
|
|
|
|
/* setup the sampling freq if PLL mode is used */
|
|
akc_write_masked(AK4537_MODE2, AKC_PLL_44100HZ, FS_MASK);
|
|
|
|
/* setup the low freq boost level */
|
|
akc_write_masked(AK4537_DAC, BST_OFF, BST_MASK);
|
|
|
|
/* setup the digital volume */
|
|
akc_write(AK4537_ATTL, 0x10);
|
|
akc_write(AK4537_ATTR, 0x10);
|
|
|
|
/* power up the DAC */
|
|
akc_set(AK4537_PM2, PMDAC);
|
|
udelay(100000);
|
|
|
|
/* power up the headphone amp */
|
|
akc_clear(AK4537_SIGSEL2, HPL | HPR);
|
|
udelay(100000);
|
|
|
|
/* power up the common voltage of headphone amp */
|
|
akc_set(AK4537_PM2, PMHPL | PMHPR);
|
|
udelay(100000);
|
|
}
|
|
|
|
void audiohw_postinit(void)
|
|
{
|
|
/* nothing */
|
|
}
|
|
|
|
void audiohw_close(void)
|
|
{
|
|
/* POWER DOWN SEQUENCE (from the datasheet) */
|
|
|
|
/* mute */
|
|
akc_write(AK4537_ATTL, 0xff);
|
|
akc_write(AK4537_ATTR, 0xff);
|
|
akc_set(AK4537_DAC, SMUTE);
|
|
udelay(100000);
|
|
|
|
/* power down the common voltage of headphone amp */
|
|
akc_clear(AK4537_PM2, PMHPL | PMHPR);
|
|
|
|
/* power down the DAC */
|
|
akc_clear(AK4537_PM2, PMDAC);
|
|
|
|
/* power down the headphone amp */
|
|
akc_set(AK4537_SIGSEL2, HPL | HPR);
|
|
|
|
/* disable MCKO */
|
|
akc_clear(AK4537_MODE1, MCKO_EN);
|
|
|
|
/* power down X'tal and PLL, pull down the XTI pin */
|
|
akc_write_masked(AK4537_PM2, MCLKPD, (MCLKPD | PMXTL | PMPLL));
|
|
|
|
/* power down VCOM */
|
|
akc_clear(AK4537_PM1, PMVCM);
|
|
udelay(100000);
|
|
|
|
akcodec_close(); /* target-specific */
|
|
}
|
|
|
|
void audiohw_set_master_vol(int vol_l, int vol_r)
|
|
{
|
|
akc_write(AK4537_ATTL, vol_l & 0xff);
|
|
akc_write(AK4537_ATTR, vol_r & 0xff);
|
|
}
|
|
|
|
void audiohw_set_frequency(int fsel)
|
|
{
|
|
static const unsigned char srctrl_table[HW_NUM_FREQ] =
|
|
{
|
|
HW_HAVE_8_([HW_FREQ_8] = AKC_PLL_8000HZ, )
|
|
HW_HAVE_11_([HW_FREQ_11] = AKC_PLL_11025HZ,)
|
|
HW_HAVE_16_([HW_FREQ_16] = AKC_PLL_16000HZ,)
|
|
HW_HAVE_22_([HW_FREQ_22] = AKC_PLL_22050HZ,)
|
|
HW_HAVE_24_([HW_FREQ_24] = AKC_PLL_24000HZ,)
|
|
HW_HAVE_32_([HW_FREQ_32] = AKC_PLL_32000HZ,)
|
|
HW_HAVE_44_([HW_FREQ_44] = AKC_PLL_44100HZ,)
|
|
HW_HAVE_48_([HW_FREQ_48] = AKC_PLL_48000HZ,)
|
|
};
|
|
|
|
if ((unsigned)fsel >= HW_NUM_FREQ)
|
|
fsel = HW_FREQ_DEFAULT;
|
|
|
|
akc_write_masked(AK4537_MODE2, srctrl_table[fsel], FS_MASK);
|
|
}
|
|
|
|
#if defined(HAVE_RECORDING)
|
|
void audiohw_enable_recording(bool source_mic)
|
|
{
|
|
(void)source_mic;
|
|
}
|
|
|
|
void audiohw_disable_recording(void)
|
|
{
|
|
}
|
|
|
|
void audiohw_set_recvol(int left, int right, int type)
|
|
{
|
|
(void)left;
|
|
(void)right;
|
|
(void)type;
|
|
}
|
|
|
|
void audiohw_set_monitor(bool enable)
|
|
{
|
|
(void)enable;
|
|
}
|
|
#endif /* HAVE_RECORDING */
|