12791d3714
information, and rewrite some sections to improve the English. git-svn-id: svn://svn.rockbox.org/rockbox/trunk@20352 a1c6a512-1295-4272-9138-f99709370657
63 lines
3 KiB
TeX
63 lines
3 KiB
TeX
\subsection{Battery Benchmark}
|
|
The \setting{Battery Benchmark} plugin enables you to test your battery's
|
|
performance whilst using your \dap\ normally. Results can be submitted
|
|
to the \wikilink{BatteryRuntime} wiki page.
|
|
|
|
\subsubsection{How it works}
|
|
Once loaded, \setting{Battery Benchmark} runs in the
|
|
background recording various information about your battery to memory.
|
|
A new point is written to memory every minute.
|
|
Every time the disk is accessed for any reason
|
|
(such as refilling the audio buffer, opening a directory or entering
|
|
USB mode etc.) then the information in memory is written to disk.
|
|
Once the memory becomes full (after many hours), then the data
|
|
are written to disk anyway. This is done so that the data are not biased by
|
|
excessive additional disk accesses. The file is written to the root
|
|
directory of your \dap\ and is called \fname{battery\_bench.txt}.
|
|
The plugin will continue to log info until:
|
|
|
|
\begin{itemize}
|
|
\item Another plugin is loaded.
|
|
\item The \dap\ is shut down.
|
|
\item The battery is empty.
|
|
\end{itemize}
|
|
|
|
Benchmarks can be resumed if
|
|
you accidentally load a plugin, or turn off your \dap, so long as the log
|
|
file \fname{battery\_bench.txt} is not deleted.
|
|
|
|
\subsubsection{Information explained}
|
|
At the top of the \fname{battery\_bench.txt} file is various
|
|
information on how to use the plugin, followed by the data themselves.
|
|
|
|
\begin{description}
|
|
\item[Time] This column reports the total time of operation of the \dap. It is
|
|
not the time that you started the plug-in. If you have your \dap\ on for 5
|
|
minutes and then start the plugin, it will start measuring from 5 minutes.
|
|
\item[Seconds] The same as \config{Time}, except measured in seconds.
|
|
\item[Level] The percent level of the battery estimated by Rockbox, and not the
|
|
actual battery level. The actual battery level can be seen from the
|
|
\config{Voltage} column
|
|
\item[Time Left] This shows the time remaining until the battery is empty,
|
|
again as estimated by Rockbox.
|
|
\item[Voltage] The battery voltage in mV at the moment the measurement
|
|
was taken.
|
|
\item[C] This stands for Charger. An "A" in that column shows if the power
|
|
adapter was attached to the unit at the time of the measurement.
|
|
\item[U] USB powered. Only for targets that support this. A "U" will indicate
|
|
if the unit was using the USB port for power at the time of the measurement.
|
|
\end{description}
|
|
|
|
\subsubsection{Usage}
|
|
The log file can be used to tell you how long the battery lasted (with some
|
|
limitations, see below), but it is most useful for graphing discharge curves
|
|
in order to improve Rockbox's estimation of battery level and time remaining.
|
|
The battery log (\fname{battery\_bench.txt}) is in CSV format
|
|
(comma separated variables) and thus can be easily imported into a spreadsheet
|
|
or similar program.
|
|
|
|
\subsubsection{Limitations}
|
|
As \setting{Battery Benchmark} needs to write the data held in memory to
|
|
disk in order to save them, it is possible that should Rockbox shut down
|
|
due to low battery then there will not be enough power remaining to write the
|
|
data to disk. Therefore all measurements since the previous save will be lost.
|